*12 48. The beam is made from three polystyrene stripsthat are glued together as shown. If the glue has a shearstrength of 80 kPa, determine the maximum load P that canbe applied without causing the glue to kise its bond.30 mm40 mm-20 mm60 mmtimtinfe-08m-

Given:- Shear strength = 80kPa=80* 103Pa To find:- P

Answered: *12 48. The beam is made from three…

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.15P: Estimate the elastic and plastic strain at the ultimate tensile strength in the low-carbon steel...

See similar textbooks

Similar questions

PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
Two polymer bars are connected to a rigid plate at 8, as shown. Bar (1) has a cross-sectional area of 1.42 in.and an elastic modulus of 2180 ksi. Bar (2) hasa cross-sactional area of 1139 in.and anelastic modulus of 4150 ksi. Assume l-23 in., L-41 in, Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Datermine the horizontal deflection of end Crelative to end A P R (1) (2) Answer: uga in.
A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m Figure P-211 Aluminum A = 320 mm² 1.5 m 2P
A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1200 psi for the plywood and 700 psi for the boards. The working shear stress for the glue is 50 psi. Determine the dimensions band so that thejoint is as strong as the boards.
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m 10KN 0.8m 0.4m 5KN 0.6m What is the deformation 8Rc in mm? Al 20KN A=800 mm? A=1,200 mm²
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.71 in and an elastic modulus of 2050 ksi. Bar (2) has a cross-sectional area of 1.019 in? and an elastic modulus of 3910 ksi. Assume L-20 in. Lyn47 in. Q-6 kips. P-3.6 kips, and R-13.2 kips. Determine the horizontal deflection of end Crelative to end A. (1) (2) Answer: UCIA - in.
A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1200 psi for the plywood and 700 psi for the boards. The working shear stress for the glue is 50 psi. Determine the dimensions b and t so that the joint is as strong as the boards.
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the steel. Steel Brass Copper Est = 200 GPa Ebr = 100 GPa Ecu = 120 GPa %3D ast = 12(10-6)/°C abr = 21(10¬6)/°C acu = 17(10-)/°C %3D Acu = 515 mm² |Ast = 200 mm? Abr = 450 mm² %3D 300 mm- 200 mm 100 mm O -0.0058mm O 0.0165mm O -0.0165mm O 0.0058mm
Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze 480 mm² 650 mm² 3P 1.0 m 4P 2.0 m Aluminum 320 mm² 1.5 m 2P
A beam is made of four planks glued together. Knowing that the vertical shear in the beam is V = 500 N, determine the minimum required shear strength Tg for the glue. 50 mm 50 mm 50 mm V D B 150 mm 50 mm 150 mm 50 mm
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²

SEE MORE QUESTIONS

Recommended textbooks for you

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

*12 48. The beam is made from three polystyrene strips that are glued together as shown. If the glue has a shear strength of 80 kPa, determine the maximum load P that can be applied without causing the glue to kise its bond. 30 mm 40 mm -20 mm 60 mm timtinfe -08m-