The homogenous material wire ABCD is bent as shown and is attached to a hinge at C. <10> Determine the length L in mm in which portion BCD of the wire is horizontal in position. <10> Determine the length L in mm in which portion AB of the wire is horizontal in position (meaning portion BCD is inclined) - 80mm B IC 60 mm

The homogenous material wire ABCD is bent as shown and is attached to a hinge at C. <10> Determine the length L in mm in which portion BCD of the wire is horizontal in position. <10> Determine the length L in mm in which portion AB of the wire is horizontal in position (meaning portion BCD is inclined) - 80mm B IC 60 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter8: Engineering Materials

Section: Chapter Questions

Problem 85CQ

See similar textbooks

Similar questions

3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
The thin uniform plate shown has a mass of 100kg and is subjected to a force and couple momentalong its edges. If it is supported in the horizontalplane by a roller at A, a ball-and-socket joint at B,and a cord at C, determine the components ofreaction at these supports to maintain equilibrium. Please provide all written work and show FBD. Thank you!
2m 2m 12₂ 2m y 2N/m ✓ 2N/m 2m $ بلا
The double - riveted joint connects two plates which are each 3.0 mm thick, and the rivets have a diameter of 4 mm., if the failure strength of the rivets in shear is 370 N/mm2 and the ultimate tensile strength of the plate is 465 N/mm?, determine the necessary rivet pitch b (mm) if the joint is to be designed so that failure due to shear in the rivets and failure due to tension in the plate occur simultaneously. Calculate also the joint efficiency n (%). 3 mm 4 mm diameter
(c) The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. ----|--²--| A 9 DAB T L P Fig. Q1(c) PL Hint: S = note that ABC is a rigid bar. EA C
The wire AB is unstrentched when tetha = 45 degrees. If a load is applied to the bar AC, which causes tetha to become 46.7 degrees. Determine the normal strain in the wire.
Use the subsne member to make a compieneanlyss of e comples uss shown 25kN d 3m 25KN 4 m e1.5 m 2 at 4 m = 8 m
(2) 4 0 5 211 5 4 #9 4 "1 16 #3" ft-k fé = 3 ksi, M = 90 NWC. The section is cracked. Computer the bending stresses in the beam by using transformed-area metho
9 Determine the shearing stress, In MPa, on the fiber 30mm above NA at distance 1m from A 10 Determine the spacing, in mm, of rivets on the steel plate
Learning Goal: To determine an l-beam's maximum bending moment, moment of inertia using the paralel-axis theorem, and the maximum stress at a given location using the flexure formula As shown, I-beam ABC supports a sign having a mass of S= 11 kg The l-beam is 740 mm long and is further supported by a rod that is attached 420 mm from the wall. Assume that all forces acting on the l-beam act along its centroid and that the l-beam's weight is negligible. Let the dimensions of the l-beam be w = 90 mm g= 25 mm, h = 70 mm j= 25 mm, c= 110 mm B Part A - Free-body diagram of beam ABC Before the problem can be analyzed, a free-body diagram must be drawn to understand the forces and reactions that act on the -bam. Drew the free-bady diagram of beam ABC. A free-body diagram includes the forces acting on the object, in this case the beam. Start your vectors at the black dots. You will not be graded on vector length. Ignore all reaction forces in the x direction, and assume all vertical reaction…
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
4.Calculate and determine the nature of the forces in the bar EF,FC ,and BC with ritter cut method 30 B - 2 m - -2 m- -2 m- A = Sendi D- Rol 30 kN 30 kN A=Sendi (Joints) D=Rol (Rollers)