1.1 A beam ABC 12 m long is simply supported at A and B where AB = 8 m. Point loads of 15 kN and 6 kN are applied at the mid-point of AB and at C respectively. A uniformly distributed load of 4 kN/m extends for 6 m from A. Determine the values of the reactions by resolving and taking moments. Check your results by using virtual work. Sketch the shear-force and bending-moment %3D

1.1 A beam ABC 12 m long is simply supported at A and B where AB = 8 m. Point loads of 15 kN and 6 kN are applied at the mid-point of AB and at C respectively. A uniformly distributed load of 4 kN/m extends for 6 m from A. Determine the values of the reactions by resolving and taking moments. Check your results by using virtual work. Sketch the shear-force and bending-moment %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
a) Find the displacements at point C of the frame using Finite Element Method. b) Draw the stress resultant diagrams (M, N, T). 70[kN]| 50 kN / m 30 (cm) B 60(cm) 1.5 m) E=28 GPa. 1.5(m) 9 (m)
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young’s modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work.
The overhanging beam is supported at A and B and has a uniformly distributed loading w = 15.8 kN/m as shown in the figure. Determine the max shear force in the beam. Input your answer as a value only in KN to one decimal place without +/-sign. W 2m 4 m B
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 25 kN/m, L = 12.6 m and El = 5.7 x 104 kN-m² is constant for the beam. A Answer: (a) Ay = i Cy= i Mc = i (b) Vmax Mmax = i i W L/2 B L/2- ! kN ! kN kN•m KN kN.m
.. The continuous beam is loaded as shown in the figure. A is a fixed support, while B and C are roller. Assume that supports do notsettle, and El is constant. Using the consistent deformation method determine the following: a. Reactions at the supports. b. Sketch the shear and moment diagram of the beam. c. Determine the value and location of maximum shear and bending moment of the beam. A Sm 50 kN 5m 15 kN/m B 10m 60 kN Im D
Using the Method of Consistent Deformations and Beam Deflection Formula. A two-span continuous beam is loaded by a 20 and 40 kilopound (kip) force as shown in the figure. Assuming flexural rigidity as constant, determine the reactions at each support. Determine the vertical reaction at A. B & C (kips) and put a negative sign if the reaction is downward.
a) Find the rotation at point B of the beam using Finite Element Method. b) Find the stress resultants (M and T) at point D. 40 [kN / m] 12[kNm / m] 30 (ст) 60(cm) B E=28 GPa. 2 (т) + 4 (m) 2 (т) +
Use either the Virtual Work Method or the Method of Consistent Deformation. Please state what you use and please show the complete solution Considering the beam shown in Figure 1, E = 200 GPa and I = 2x10 ^9 mm^4 Determine the vertical reaction at support A. Determine the horizontal reaction at support A. Determine the Moment reaction at support A. Determine the vertical reaction at support C. Determine the vertical deflection of point B due to the loads Determine the horizontal deflection of point B due to the loads Determine the total deflection of point B due to the loads with respect to its original location.
3 Decimal Places 15. Use Method of Consistent of Consistent Deformation to solve the horizontal reaction at D in kN of the truss system below. Assume A = 1200 mm2, E = 200 GPa. Use a and b from the previous problem. Enter absolute value only. Thank you!
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0 m and El = 5.5 x 104 kN-m² is constant for the beam. B L/2 L/2 Part 1 Cut a cross-section through the beam between points A and B, and drawa free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x - 3.5 m. M(x) A Answer: kN-m + i m A, M(x) = i eTextbook and Media