A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 25 kN/m, L= 12.6 m and El = 5.7 x 104 kN-m² is constant for the beam.

A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 25 kN/m, L= 12.6 m and El = 5.7 x 104 kN-m² is constant for the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE THE PROBLEM USING DOUBLE INTEGRATION METHOD Problem IV. Determine the support reactions of the beam shown. El is constant for the entire beam. 20kN/m A 4m B 4m 40kN/m -X
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
for the beam and loading shown (a)use discontinnuity functions to write the expression for w(x). include the beam reactions in this expression. (B) intergrate w(x) twice to determine v(x) and m(x). (C) Use v(x) and m(x) to plot the shear- force and bending- moment diagrams.
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN.b. Moment Reaction at C in kN-m.c. Deflection at point B in mm.d. Maximum deflection on the beam in m Valuea = 4.8b = 28c = 11 Thank you very much!
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0 m and El = 5.5 x 104 kN-m² is constant for the beam. B L/2 L/2 Part 1 Cut a cross-section through the beam between points A and B, and drawa free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x - 3.5 m. M(x) A Answer: kN-m + i m A, M(x) = i eTextbook and Media
A beam is loaded and supported as shown.(a) Use the double-integration method to determine the reactions at supports A and C. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated.(b) Draw the shear-force and bending-moment diagrams for the beam.Assume w = 29 kN/m, L = 11.2 m and EI = 6.3 x 104 kN·m2 is constant for the beam.
A two-span continuous beam is loaded with a concentrated force at point C and a uniformly distributed load at span AB. The support at point A settles 12 mm. Young's modulus is E = 200 GPa, and the moment of inertia of the beam is I = 500x106 mm 4. (1) Prove that the beam is statically indeterminate to 1st degree. (2) Use the Force Method to determine support reactions at A, B and D. (3) Draw the shear force and bending moment diagrams for the beam. 12 mm settlement 3 kN/m OB 2m 4 kN 2m
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and B. (b) Draw the shear-force and bending-moment diagrams for the beam. (c) Determine the deflection in the middle of the span. Assume w = 11 kN, L = 7.4 m and El = 6.9 x 10 kN-m2 is constant for the beam. B Part 1 Draw a free body diagram of the beam. Use symmetry to determine support reactions A, and Cy. MA MB В L. By Answer: Ay kN i By = kN
Please solve using 3 kip instead of 2 kip for the downward force 2 kip at P a 60° 1 kip The end of a cantilever I beam supports forces from three cables. a) If P = 0, determine the resultant force applied by the two cables to the I beam and report your result using polar vector representation. b) Repeat Part (a) if P = 1.5 kip and ? = 30?. c) With ? = 30?, what value of P will produce a resultant force that is horizontal? d) If the resultant force is to be horizontal and Pis to be as small as possible, determine the value ? should have and the corresponding value of P.
3. A T-shaped structure is acted in by a distributed load that varies from 100 N/m to 0 N/m and by a force P. Attached at A and C are two cables. Each of the cables is attached to a ring at E. A 600 N weight is suspended from the ring. The structure can rotate about B but is held in the position shown by the force P. a. From the geometry of the problem, determine the distance d, b. If the total moment about B is equal to zero, what is the magnitude of force P, and c. Determine the tensions in cables EA and EC. B 100 N/m 0.825 A 1.50- P 78° -0.625 260 E 600 N
.. The continuous beam is loaded as shown in the figure. A is a fixed support, while B and C are roller. Assume that supports do notsettle, and El is constant. Using the consistent deformation method determine the following: a. Reactions at the supports. b. Sketch the shear and moment diagram of the beam. c. Determine the value and location of maximum shear and bending moment of the beam. A Sm 50 kN 5m 15 kN/m B 10m 60 kN Im D
A beam is loaded and supported as shown. Use the double-integration method to determine the reactions at supports A and B. Assume wo = 10 kN/m and L = 9 m. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. Cut a cross-section through the beam and draw a free body diagram to the left of the cut. Determine the internal bending moment in terms of Ay. Check your equation by solving for M(x) at x = 4.5 m. Answer:Mx=4.5m = kN·m + m Ay