1. Find the transfer function Z(s)/F(s) for the following block diagram. Make sure that you simplify the final answer.

Q: Consider following assembly instructions: MOV A,#24 H MOV B,#6B H MUL AB What will be the final…

A: MOV A,#24 H this is known as immediate addressing mode because it transfer the 8-bit data into the…

Q: Q14: The arithmetic shifts right instruction ashr means divide the number by 2. Find the result of…

A: First 08 is loaded into the Acummulator in the form of binary. Given that ashr means divide the…

Q: Can tutor write the explanation more clearly as I don't understand the hand writting

A: A flip flop change it's output at active edge of clock.  Preset is used to set the output of flip…

Q: Question 1 You have a supply of 8K x 4 memory chips. The address bus on each chip will be. (Type out…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Which of the following is NOT included in MMDST kit? Small bell with 2 ½ inch diameter opening…

A: The solution is given below.

Q: The full form of PIPO is

A: Given, PIPO

Q: Choose the correct instruction that will read data in from an I/0 device. IN AL, 60 IN 60, AL OUT…

A: In an I/O device the command "IN" represents the input command Here IN AL,60 means that move a…

Q: Can you redo this again? I need step-by-step solution, like there should be Step 1, Step 2, Step 3,…

A:

Q: (input) A B C D Hex display What will be displayed on the Screen?

A:

Q: It's hard to read，  I need handwrite solution

A: Given: To find: For all circuits, i) Transfer function, ii) Magnitude response, iii) Phase…

Q: The number of possible values for signals is restricted. a. Analog b. Digital c. Either (a) or (b)…

A: A digital signal is a signal which is represented as s sequence of discrete values.  In digital…

Q: Add these hex numbers by converting each symbol to decimal and then converting the answers back to…

A: Addition and conversion to Hex

Q: When no key is pressed the input port (Port B) will read

A: in the given circuit the matrix connected two ports are given in which port A output is applied to…

Q: *13. Compute the missing values to complete the following table relating to analog to digital…

A: We know relationship between analog input and digital output .

Q: Enter the correct value (either 1 or 0) in each box; consider each row carefully before deciding on…

A:

Q: In N-channel JFET the Id is controlled by___ a. Vds O b. lg O c. Idss O d. Vgs

A: JFET is controlled by the Gate voltage and current equation in saturation region is given by , ID =…

Q: 27 In the following question a number series is given with one term missing. Choose the correct *…

A: The pattern is +2 and multiply 2 i.e. 4+2=6 6*2=12 12+2=14 14*2=28+28+2=30 So next will be 30*2=60

Q: Fill in the Blank: A is a Punch Down Block which has 25 rows of four metal pins.

A: The 66 block is the punch down block that is used for connecting the wire a telephone line system.…

Q: Need solution within 15 mins. Give 5 stars for correct solution

A: The solution is provided in the following section:

Q: Convert the OCTAL NUMBER 65 40.7 20 2 to decimal number. Answer = %3D

A:

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: N 5 3 a (ON) b. ..(.....). 3 coon 3 Hello expert, I need to convert the drawing from handwriting to…

A: A relay has two types of contacts. NO contact & NC contact Here, NO Contact: NO mean normally…

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: I can't clearly see the lines in the column of the equation.

A: De Morgan's theorems can be expressed as A+B=A.B--->(1)A.B=A+B--->(2)

Q: The type of error that is associated with measurement instruments or techniques is error.

A:

Q: Solve for ID in IMG 18 V 2kQ 1100 mA. round off your answer with 1 decimal value V-1.7 V 0.51 k

A: FET are voltage controlled device. BJT is current controlled device JFET is stand for Junction field…

Q: Draw a 4:1 multiplexer using 2:1 multiplexers

A: Designing 4:1 multiplexer using 2:1 multiplexers

Q: 1. Determine R- and IT. 302 2 362 20s2 10oV 252 $362 1o2

A: Determine equivalent resistance and total current for the given circuit.

Q: Choose the correct instruction that will send data to an 1/0 device. IN AL, 60 O IN 60, AL OUT 60,…

A: MOV instruction : Copies the data item referred to by its second operand (i.e. register contents,…

Q: It's hard to read, I need a clearly handwrite version

A:

Q: im still confused can you break it down more for me please

A:

Q: The given system has accuracy.

A: Accuracy

Q: Choose the correct instruction that will send data to an l/0 device IN AL, 60 IN 60, AL OUT 60, AL…

A:

Q: 6. What are the different types of oscillator?

A: Solution: Oscillators are mainly classified into two categories Linear oscillators Nonlinear…

Q: The desirable static characteristics of a measurement are precision O accuracy sensitivity all of…

A: In a measurement devices (for example any meter such as ammeter or voltmeter or any other meter) is…

Q: 15.0 V 500 Q Ο 165 mA 0 175 mA C 55 Α ο 1ος ΠΑ 2 ΚΩ

A:

Q: Q1/The Gray code ( 10110111101)= ( ) in decimal number 1753 931 869 None of them 1877 1750 1749 867

A: We need to convert the given gray code to Decimal number