The desirable static characteristics of a measurement are precision O accuracy sensitivity all of these O O O O

Q: QUESTION 10 With reference to the instruction below, what will be the value of each of the bits in…

A: First we should select the correct option for given instructions Value of each bit in word B3:3 will…

Q: Do the following binary subtraction: 111001110.11111- 010000000.01111 (The final answer must be…

A:

Q: "Implement the yellow highlighted table using multiplexers considering the digits used above (88 72…

A: According to the question, for the given table as shown belowWe need to implement the yellow…

Q: Quèstion 6 In order to avoid the indeterminate state of the SR latch, the JK latch was designed the…

A: In SR latch when we give S=1 and R=1 it shows the indeterminate state.  truth table of SR flip flop…

Q: Q6- Assume a delay of zero for the latch in this part. Complete the timing diagram for the gated D…

A:

Q: What is the maximum number of digits that may be used in the Octal System?

A:

Q: (NEED A NEAT HAND WRITING SOLUTION ONLY OTHERWISE WILL LEAVE A DOWNVOTE)

A: Given: A binary channel,  with  λ=0.5,Px=0=1-p, Px=1=p,  To find: The value of p that achieves the…

Q: . Determine the truth table of the digital çircuit shown in the figure below and explain its…

A:

Q: During the execution of an OUT instruction, the /0/M signal will Go low. Tristate. Not be used. Go…

A: Io/M is an active low signal means it can be activated by providing thr low input

Q: What is the maximum number of digits that may be used in the Octal System

A: We need to find out the number of digits in octal system .

Q: estion 4 ruction for each group of fallowing instructions Assuming no forwarding or hazard…

A: Assuming no forwarding or hazard detection, add the suitable number of NOP instructions for each…

Q: Quèstion 20 Consider a binary code 8,4,-2,-1, The decimal equivalent to the 8,4,-2,-1, coded number…

A:

Q: 11. What is the count range of the Asynchronous counter shown below? T 12. CLK 30 30 SCLE 74LS76N…

A: Given counter is Asynchronous Counter because clk is given first flipflop and then output of first…

Q: What is the maximum number that we can count up to using 14 bits?

A: The smallest storage unit is referred to as a Bit. Bit stands for Binary Digit. A bit stores any one…

Q: 6. A digital signal is sent using a Hamming code for error detection and correction. The signal…

A: The parity code is checked as shown below.

Q: PAL consists of O a. a programmable array of AND gates followed by a fixed array of OR gates O b. a…

A: PAL is programmable Array logic in which AND gates are programmable and OR gates are fixed…

Q: can you explain in detail what is random errors and how to limit it

A: A coincidental discrepancy between the observed and true values of anything is known as a random…

Q: odd parity is selected on a tow bit parity generator and data A= LOW , B= HIGH the parity bit will…

A: This is based on the odd parity If the odd parity is selected on a two bit parity generator and data…

Q: 3 Given the following AHDL code, explain how this code "debounces" a pushbutton. If a key is…

A: Given  AHDL program ro debounce a pushbutton. We need to explain how debouncing occur. Please find…

Q: Assume that carry flag is 1 at the beginning, and execute the following code: mov al, OE8H rcl al, 1…

A:

Q: QUESTION 19 To perform the operation (76425 – 28321) using 10's complement, we should first find the…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Add the following BINARY NUMBERS 101110111.10111 + 10100000 1.110 10 (Note: The problem should be…

A: The binary number system is a base-2 number system. So the numbers are represented using 1's and…

Q: BINARY NUMBERS

A: Given- Binary digit- B1 = 10001.0001 B2 = 101.11

Q: Can I get a version of this that can be read?  Maybe a space between equations could help.  Better…

A: It is given that:

Q: The information signal is always an analog signal. an analog signal in case of an analog carrier…

A: A signal can be in form of analog or digital signal.

Q: * Question Completion Status: - A Moving to another question will save this response. estion 15 The…

A: In this we will find binary of 37 decimal..

Q: Hamming codes have a minimum distance of 3. What are the error-correction and error-detection…

A: Hamming codes have a minimum distance of 3, which means that the decoder can detect and correct a…

Q: Add the following BINARY NUMBERS 111000001+ 110010110 (Unused boxes in the answer must be filled…

A: In this question we will perform binary addition...

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: Add the following BINARY NUMBERS 101100111.11011 + 100010111.00010 (Note : The problem should be…

A:

Q: 12.OR AX, 0300H a. Clears bits 8 and 9 b. Set bits 8 and 9 c. Invert bits 8 and 9

A: The given instruction is: OR AX, 0300H

Q: QUESTION 10 With reference to the instruction below, what will be the value of each of the bits in…

A: The destination of the CLR (clear) instruction has a value of bits. All of the bits in the…

Q: Assembly language: O is easier to program in than high-level languages. O All of these are correct.…

A:

Q: Do the following binary subtraction: 110011010.00011- 001001011.00110 (The final answer must be…

A:

Q: this is incorrect. please resolve and answer should be 0.5

A:

Q: Which one is the true statement a. Open loop systems are less affected by noise b. Open loop systems…

A: For option (a): Open loop control System. This type of control system does not have any feedback and…

Q: November - 27 November > Midterm exam 8/3/2021 morning Nhat is the addition of the binary number…

A:

Q: 1) Convert the 8,4,-2,-1 sequence (01101011)84-2-1 to decimal

A: As per company guidelines we are supposed to answer only one question. Kindly repost other questions…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.