EYA98B/sdocs.google.com/forms100PapertineJ MAPapertinePapertine45 - ls-das #2: For the Simply supa ted beam having the SechinShown and londed partially, Find:1. Draw the bending moment diagram ?2. Find the value of the maximum bendig moment Mmak3. Find the value f the maximum bending stress Vmaxال لعة البطم رات المطع الو ضع المكل والحملة۱. أسم الر البان لعن اوكماو: Mmax sls! e de i ană ficأوجه تعة أ على إ دإما کےļ UmaxKN/m- 20 Cm41 m.2 m.1 m.Neutral40 cmAxisBeam (AB)Beam Cross- Sectionت إضافة ملف

UDl of 4kN/m for 2m lies at the center of the beam Total load on the beam = 4x2 =8KN Apply…

1. Draw the bending moment diagram ? 2. Find the value of the maximum bendig 3. Find the value of the maximum bending stress Vmax? g moment Mmait ال لعة البطم رات المتطح مز ثا أُوصد ١. أ الرم البمان لحز اوحماء ؟ Mmax أرص قمة أعا عرم انار Vmax أوج قعة أعلن إم دإا کے 4 KN/m 20 Cn B Neutral Axis 1 m 2 m. 1 m. 40 cm Beam (A B) Beam Cross- section

1. Draw the bending moment diagram ? 2. Find the value of the maximum bendig 3. Find the value of the maximum bending stress Vmax? g moment Mmait ال لعة البطم رات المتطح مز ثا أُوصد ١. أ الرم البمان لحز اوحماء ؟ Mmax أرص قمة أعا عرم انار Vmax أوج قعة أعلن إم دإا کے 4 KN/m 20 Cn B Neutral Axis 1 m 2 m. 1 m. 40 cm Beam (A B) Beam Cross- section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute the maximum tensile and comprsive stresses devloped in the beam that is loaded and has the cross-sectional properties shown in fig 8 KN 120 mm 10 KN/m ΝΑ A 1=20 x10 6 mm4 4m B C 1m 50 mm
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
Plz solve within 30min I vill give definitely upvote and vill give positive feedback
Jertical beam of the applied to a shown. Determine forces are cross section compressive BC of the the maximum Stresses bRam. tensile and portion. 9,25 kN in 45mm I10mm 30 mm 30mm 400mm 500mm
Calculate the magnitude of FFB in the truss. E 2000 N 1000 N D 4 m B в 4 m
A steel rod composed of two parts (AD and DB), which have different cross-sectional area, is fixed at A. 80KN 20KN 30сm 30cm 60cm This rod is subjected to loads 80kN at C and 20kN at D. (Area)AD=20cm? -(Area) DB=10cm cross-section of D-B cross-section of A-D Determine the elongation of the rod shown in the figure. Take the elasticity modulus for steel E=200GP..
The rope ABexerts a 46 - N force T on the collar at A Let rCA be the position vector from point C to point A. (Figure 1) Figure K 1 of 1 > 0.15 m 0.4 m 0.2 m 03m 05 m 0.25 m 0.2 m
The cord passing over the two small pegs A and B of the board is subjected to a tension of T = 100 N. The resultant couple moment produced by the two cords is 20 Nm, clockwise. Part A Determine the minimum tension P of the cord passing over pegs C and D. P = 16.35 N T 30° Part B Determine the corresponding orientation angle of the cord passing over pegs C and D. 0 45 A 300 mm D B 30⁰ -T 300 mm
150 mm 60 mn 300 nm 000 m 50 mm 5 m B 25 kNm 5 m 10 KN A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis
The steel truss with E=200GPais loaded as shown in the figure. Determine the following: the following a) the deformation of member AB if the cross-sectional area is 2500mmb) the deformation of member AD if the cross-sectional area is 1800mm A 4.0m 200 KN B D 4.0m 1² 2.5m
Static of Rigid Bodies Prob 03: Locate the centroid of the plane area shown: y 4 in. -8 in.-
13-0v represented of .a) resistance friction) b) Safety factor for shear) c) resistance factor for shear) .d) Non all these) 14.is safety factor for shear (a) Ων (b) b (C) Ω d) Øv 15-.the Values of Øv and 2v far will depend on. .a) the flange width to thickness ratio) b) the web width to thickners ratio) c) Lp and Lr) (d) (b) and (C)