Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque) and a tensile force, the axial tensile stress is 30 MN m-2 and the shear stress 50 MNm (Figure ). Estimate the principal stresses and draw the inclined element with the principal stresses r= 6 mm d = 30 mm D = 40 mm. Y-face D 50 X-face 30MN m-2 30 50 MN m-

Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque) and a tensile force, the axial tensile stress is 30 MN m-2 and the shear stress 50 MNm (Figure ). Estimate the principal stresses and draw the inclined element with the principal stresses r= 6 mm d = 30 mm D = 40 mm. Y-face D 50 X-face 30MN m-2 30 50 MN m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer to the question in engineering resistance
A solid 0.66-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 Ib-ft 50 lb-ft 70 Ib-ft 30 lb-ft 1594psi 2126psi 1981psi 1786psi 2936psi
9 MPa 7 MPa 5 MP 1. Draw the appropriate Mohr's circle. 2. Get from the circle oi and o2, Umax and its corresponding normal stress (Oevg). Show these points on the circle. 3. Show on the circle the angles 20p and 20s that correspond to the orientation of principal planes and the planes of maximum shearing. 4. Solve point (1c) above graphically using the circle ik. show that your graphical solution is giving the same results as obtained by the analytical equations in point (1c) above.
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of the shear stress at point a of the n-n section |τ| Specify in MPa units. Take the P value of 34 kN and the D value of 17 mm in the question.
A beam has the cross section shown (thin-walled profile). The shear center is at a distance, e = 32.7 mm from the web, IEN = 1134000 mm4. If a force V = 30 kN is applied, passing through the shear center as shown, determine the nearest value of the shear stress in the web at C. |5 mm 3 mm 3 mm 30 mm D 80 mm 30 mm mm E F 55 mm а. 117 МPа O b. 70 MPa Ос. 138 МРа O d. 94 MPa
Given data: L1= 220mm L2= 180mm L3= 370 mm d1= 32mm d2= 12mm
In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm². The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. D 1.7m 1.7m -P B 3.5m7 Find the location x of the largest additional vertical force that can be applied to the bar. meters in 2 decimal places
Subject:
-2.4m- 8 mm 200 mq 8 mm 250 mm 8mm The steel beam has the cross-sectional area shown. The beam is loaded as shown with the intensity of the distributed loading w=70 kN/m. Determine the absolute maximum bending stress in the beam in MPa.
WHICH OF THE FOLLOWING GIVES SHERARING STRESS IF a=3inches Which of the following gives the minimum permissible dimension if the shearing stress is limited to 6000 psi
lute flexural stress. For the beam shown in Figure (3), given INA = 1.+ 10 mm", calculate the transverse shearing stress at points A, C and G on the section at the left support of the beam.