A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P- 92 kNand torques Tg- 17 kN-m and Te- 6 kN-m, which act in the directions shown. Determine the horizontal shear stress Tyat point H.(1)TcO 38.09 MPaO 45.57 MPaO 23.45 MPaO 35.46 MPaO 48.30 MPa

Answered: Image /qna-images/answer/da803926-e7a6-4274-8132-b6b36494e0de.jpg

A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P - 92 k and torques Tg - 17 kN-m and Tc- 6 kN-m, which act in the directions shown. Determine the horizontal shear stress Ty at point H. (2) O 38.09 MPa O 45.57 MPa O 23.45 MPa O 35.46 MPa O 48.30 MPa

A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P - 92 k and torques Tg - 17 kN-m and Tc- 6 kN-m, which act in the directions shown. Determine the horizontal shear stress Ty at point H. (2) O 38.09 MPa O 45.57 MPa O 23.45 MPa O 35.46 MPa O 48.30 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). a.)3.86 ksi b.) 3.51 ksi c.) 3.15 ksi d.) 5.38 ksi e.) 4.85 ksi
A solid 1.250-in-diameter steel shaft is subjected to torques Tg- 190 Ib-ft and Tp- 115 Ib-ft, acting in the directions shown. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque Tethat can be applied to the shaft. Te Tp Ib-ft Answer: Te= i
View Policies Current Attempt in Progress A solid circular steel shaft having an outside diameter of D = 1.25 in. is subjected to a pure torque of T = 2390 Ib-in. Determine the maximum shear stress in the shaft. O 5.25 ksi O 5.64 ksi O 4.37 ksi O 8.67 ksi O 6.23 ksi
Equation of Torsion Question 5: A solid steel shaft is to transmit a torque of 10 kN-m. If the shearing stress is not exceed 45 MPa, find the minimum diameter of the shaft - 1. 104 mm 2. 01 mm 3. 1040 mm 4. 10 mm
-2 m 2 m Problem 3: The frame supports the loading shown. The pin at A has a diameter of 50 mm. If it is subjected to double shear, determine the average shear stress in the pin. (8 pts) E 60 kN 3 m
A solid shaft has diameter of 80 mm. it is subjected to a torque of 4 kN-m. The maximum shear stress induced in the shaft would be A 75/π N/mm 2 B 125/π N/mm² C 150/π N/mm D 250/π N/mm²
Current Attempt in Progress The horizontal shaft with a diameter of d- 43 mm is supported by a thrust collar that rests on a 29-mm-thick plate. The thrust collar is 20-mm thick. The thrust collar has an outer diameter of Dcollar - 63 mm. Determine the load P that causes an average shear stress of 69 MPa on the cylindrical surface of contact between the shaft and the thrust collar. Thrust collar area Plate d Thrust collar Dcollar Answer: P- kN
Determine the maximum shear stress in the A992 steel shaft below. Also, determine the angle of twist of point B with respect to point A. The shaft has a diameter of 50 mm. 500 N m А 1000 N m/m 0.5 m 0.5 m B
Q3/ For the beam and loading shown, determine the maximum normal stress due to bending. 150 kN 150 kN S0 mm 90 kN/m D VE B. 300 mm 24 m b.5 m osm -05m
P7-L In cach case,calculate the value of Q and i that are used in the shear formula for finding the shear stress at A. Alsa, show how the shcar stress acts on a differential volume element located at point A. fa2m 02m tazm al aim (d) al m 03m 03 m taim Fozm le) a5m falm 402m 0.3m talm 01m (c)
A shaft 100mm in diameter and 3m long, with bult-in ends, is subjected to a clockwise torque of 4KN-m applied 1m from the left end, and to another clockwise torque of 16 KN-m applied 2m fromthe left end. 16. Compute for the shearing stress at segment AB. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 17. Compute for the shearing stress at segment BC. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 18. Compute for the shearing stress at segment CD. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa
350mmi The simply supported beam has an I-shaped cross section. (1) Determine the values and locations of the maximum tensile and compressive bending stresses. (2) Sketch the bending stress distribution over the cross section on which the maximum bending stress occurs. No credits if free body diagram is not present. 0 35m 11mm 8 kN/m 100 kN 7.5mm 11mm 0.8 m 2 m 54 1.0m 175mm 1100KN