Answered: Compute the maximum tensile and…

Compute the maximum tensile and comprsive stresses devloped in the beam that is loaded and has the cross-sectional properties shown in fig 8 KN 10 KN/m L A 4m 1=20 x10 6 mm4 B с 1m NA 120 mm 50 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
A
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm