The one end of a hollow square bar whose side is 10 in with 2 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and Oll 243 ksi for pin material.

The one end of a hollow square bar whose side is 10 in with 2 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and Oll 243 ksi for pin material.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A prismatic wing box is constructed of two cylindrical tubes (each of thickness 2t) welded to top and bottom plates (of thickness t), resulting in the thin-walled (t < a) cross-section shown below. It is subjected to an axial torque T. (a) Find the torsion constant, J, of the cross-section. (b) Find the location and value of the maximum shear stress, Tmax- 2t -2t 10a
The lap joint carries an P axial load of P - 50 kN. It is connected by 3-18 mm 150 mm 20 mm 20 mm dia. rivets. 38. What is the bearing stress between a plate and a rivet? 39. What is the shear stress in rivet? 40. What is the maximum average tensile stress in each plate?
6. A circular bar is to carry a fluctuating torque from 25 to 55 N-m. Use AISI C1144 OQT 1000for the bar and compute for the required diameter for a design factor of 2. Attachmentsproduce a stress concentration of 2.5 near the ends of the bar. please also give the FBD, thank you
A 25 mm diameter steel bar is loaded in double shear until failure, the ultimate load is found to be 446 KN. If the allowable stress is to be based on a factor of safety 3, what must be the diameter of a pin designed for an allowable load of 26 KN in single shear be?
The one end of a hollow square bar whose side is (10.13) in with (1.13) in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ_all=243 ksi for pin material.
10 rivets are fastened on a lap joint of 1.25 inch in diameter the thickness of the lap join were measured at 0.85 inch. find the maximum load that can be applied if the allowable stresses were 24 ksi for bearing in the plate and 18 ksi for the shear in each rivet. Friction between plates 1/3 the applied. What is the Illustration?
Please give the given, required, and the solution. Draw the free body diagram and label properly.
The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and Oallowable = 243 ksi for pin material.
The lap joint shown is fasted by 20mm diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 96MPa and the bearing stress is limited to 124 MPa. Assume the Applied load is uniformly distributed among the four rivets.
A cast aluminum cylinder of a portable hydraulic riveter is d 210mm in diameter. The pressure of the fluid is p 16N/mm2 by gauge. Determine suitable thickness of the cylinder wall assuming that the yield point stress is A 444MPA and factor of safety of B 6.Calculate the tangential and radial stresses at the inner, middle radius and outer surfaces.
The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ_all=243 ksi for pin material.
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?