Please answer in this format.Sketch:Given:Required:Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used)A torque To is transmitted between two flangedshafts by means of four 20-mm bolts.diameter of the bolt circle is 2=150mm. If theallowable shear stress in the bolts is 90 Mpa,what is the maximum permissible torque?Disregard friction between between flanges.TheTo

Schematic diagram of flanged shaft after considering the force F in the bo;t due to torque T

Answered: A torque To is transmitted between two…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

M P 1: Y A :s.google.com Q1 * Find the number of bolts M8 1 which made from SAE Grade 4 steel that should be used to provide a clamping force of 60 KN between two components of a machine. Also, specify the required tightening torque. (Hint: assume that cach bolt is limited to be stressed to 65% of its proof strength). 1 Add file Q2 * A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the figure below. Calculate the minimum thickness t of the plate. Given that the material of the plate can support maximum tensile stress of 75 N.mm, w = 10 cm and d = 3 cm. Thickness =t F 1 Add file Submit Clear form II
Q1: Design and draw a cast iron flange coupling for a mild steel shaft transmitting 80 kW at 220 rpm with the following specifications: Allowable shear stress in the shaft = 400 MPa Permissible angle of twist < 1° in a length of 20 diameters Allowable shear stress in the coupling bolts 30 MPa Rigidity modulus of shaft materials = 85 GPa Allowable shear stress for hub material = 15 MPa You may adopt, width of key = 25 mm, thickness of key = 14 mm You may also consider that the shaft and key are made of the same material. Four number of bolts are to be used in the coupling. Find out the diameter of the shaft required and main dimensions of the flanges and the key. Adopt suitable dimensions. Draw a neat sketch for the flange coupling with the designed dimensions.
! Required information A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R1and R2. The shaft is loaded with a transverse load of 13 kN as shown in the figure. The shaft is made from AISI 1060 hot-rolled steel. The surface has been machined. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 200 mm 50 mm 25 mm 13 kN R1 R2 Not to scale. Determine the minimum fatigue factor of safety based on achieving infinite life.
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter dp / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gp = 28 Gpa. R Rs Rb
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter d, / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, G, = 28 Gpa. %3D Rs Rp
Q2/ A 3/4in-16 UNF SAE grade 5 bolt is subjected to a load of 8 kip in a tension joint. The initial bolt tension is F 30 kip. The bolt and joint stiffness's are kb=8 & km=15Mlbf/in, respectively. a) Determine the preload and service load stresses in the bolt. Compare the to the SAE minimum proof strength of the bolt. b) Specify the torque necessary to develop the preload.
L21. Figure P4-21 shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is to be 500 lb, specify a suitable diameter for the steel pin if it is to be made from SAE 1040 WQT 900. 4-21
Read the question carefully and give me all right solutions. Internal torque at rod 1 (kip-ft) Magnitude of shear at rod 2 & 3(ksi) Rotation angle at rod 1 (deg) Rotation angle at flange C (deg)
Required information For a bolted assembly with six bolts, the stiffness of each bolt is kb 2 Mibf/in and the stiffness of the members is km = 13 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. It is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts once the load is applied. The maximum bolt preload that can be applied is Ibf.
topic: torsion in circular shafts The hollow shaft used in the system has the following conditions: Outer diameter (Ø): 150 mm Ø Allowable Shearing Stress: 85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.
Problem 2 For each of the structures shown in Fig.2, sketch the following: Free body diagrams showing the magnitudes of all applied loads, reaction forces/moments, and parts dimensions) Shear force and bending moment diagrams. Please indicate the critical location for failure of part. i. ii. {Hint: In some cases, you may have to draw FBD and BM diagrams in two different orthogonal planes} 196 ag 1.25-in dia. Gear A 20-in dia. 300 lbf 16 in 20⁰ A 14 in 100 Gear B 8-in dia. 9 in B 750 lb 20° b)

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A torque To is transmitted between two flanged shafts by means of four 20-mm bolts. diameter of the bolt circle is 2=150mm. If the allowable shear stress in the bolts is 90 Mpa, what is the maximum permissible torque? Disregard friction between between flanges. The To