A lap joint, consisting of 250 mm × 75 mm wooden plates, is fastened with two(2) rows of 20 mm diameter rivets . There are three(3) rivets in a row. The working stresses are 70MPa for rivets in shear and 140 MPa for plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. 2. A lap joint, consisting of 250 mm x 75 mm wooden plates, is fastened with two(2) rows of 2omm diameter rivets. There arethree (3) rivets in row. The workingstresses are 70 MPa for rivets in shear and 140 MPa for plates in bearing. Findthe maximum safe axial load P that can be applied to the joint. Assume that theload is equally distributed among the rivets.Pb=250mm75 mm20 mm ø bolts1

Width = 250 mm Thickness = 75 mm Diameter of rivet = 20 mm No. of rivets = 6 Shear stress = 70 MPa…

A lap joint, consisting of 250 mm × 75 mm wooden plates, is fastened with two(2) rows of 20 mm diameter rivets . There are three(3) rivets in a row. The working stresses are 70MPa for rivets in shear and 140 MPa for plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.

A lap joint, consisting of 250 mm × 75 mm wooden plates, is fastened with two(2) rows of 20 mm diameter rivets . There are three(3) rivets in a row. The working stresses are 70MPa for rivets in shear and 140 MPa for plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.14P: Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a...

See similar textbooks

Similar questions

Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
The lap joint is fastened with four 0.83-in.-diameter rivets. The working stress is 14.55 ksi for the rivets in shear. Find the axial load P (in lb) that can be applied to the joint. Assume that the load is equally distributed among the rivets.
The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70 MPa for shear and 120 MPa for bearing. How many 20-mm diameter rivets are required to fasten member IG to the gusset plate? What is the required area for member AI if the allowable axial stress is 180 MPa.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
The lap joint is fastened with four 3/5 in-diameter rivets. The allowable normal stress in the plates is 30 ksi, allowable shearing stress is 24 ksi for the rivets and 28 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. Include the necessary FBDs showing the involved internal forces in the exploratory sections. Your solutions are invalidated without the required FBDs.
The lap joint carries an P axial load of P - 50 kN. It is connected by 3-18 mm 150 mm 20 mm 20 mm dia. rivets. 38. What is the bearing stress between a plate and a rivet? 39. What is the shear stress in rivet? 40. What is the maximum average tensile stress in each plate?
The figure shows a flat hanger bar for supporting shop equipment in a factory. The bar is fixed to a support by means of a bolted connection. The main part of the hanging bar is 1.5 inches wide. This width varies up to 3.0 inches. A 1.0-inch diameter bolt transfers the hanger bar load to the two top bracket plates. Determine the allowable stress of the tension load P in the hanger in the following two instances: to. The allowable tensile stress in the main part of the hanger is 16,000 psi. b. The allowable stress load between the hanger bar and the bolt is 26,000 lb/pu.
The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below. Pins at A, C, and D are smooth. Determine (a)The load P.(b)The minimum diameter for pin C if it is in single shear and the cross-shearing stress is limited to 70 MPa.(c)The minimum diameter for pin D if it is in double shear and the cross-shearing stress is limited to 70 MPa.
The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be applied if the working stress are 14000 psi for shear in the rivet and 18000 psi for bearing in the plate. Assume that the applied load is distributed evenly in the 4 rivets. The plate is 7/8 in. thick and 4 in wide.