For the frame shown in Fig. 6-24a, draw the free-body diagrams of(a) the entire frame including the pulleys and cords, (b) the framewithout the pulleys and cords, and (c) each of the pulleys.3E Fx=0 +9 E fy=o1. FIMD RXAS AT A$DFing FoRLE componeAB2.Ge Pits oF POLLEYSEM=0Cx CByEAyT.AyAauLE OF RESOUTATAT B, C&A75 lbSKETCH RESULTALT(a)Fueo Manat AT BASEア(y7516OF CULUneCEradius of the pulley at B linchYadius of the Pulley at c a7s inch75 lbs7516()Distance BE 7inchDistance EA 4.5 inchDistance AV : 3.sinchAy6)7516マへ

Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Answered: 1 1. FIMD RXAS AT A D 2. ou Pids oF…

Engineering

Mechanical Engineering

1 1. FIMD RXAS AT A D 2. ou Pids oF POLLETS Bx By C- C. C. ALE OF RESUTAT AT B,C &A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

E T-50" 60 C Force ? Suppose rod AB is hinged to a fixed wall. Rope CDE is attached to the rod at C, 4 from the hinge. The rope passes over a pulley D. which is mounted on another fixed wall. The angle ACD is 60 degree. The other end of the rope is connected to a mechanism (not shown), which requires 50 lb. force to be actuated. How much downward hand force will be required at point B. 5' from the hinge, to actuate the mechanism? When the hand force is applied, what reaction force will be developed in hinge A? Assume the rod is weightless, rigid and amply strong and the rope is flexible and amply strong.
Provide step-by-step solution with complete given and formula to this problem. Draw sketch also. A mine hoist is to carry a cage loaded with ore at a total load of 8 tons. The depthof mine shaft is 328 ft. A 6 x 19 IPS wire rope with rope diameter of 1.75 in is to beuse with sheave diameter of 39 in. The cage loaded is to start from rest and will attaina maximum velocity of 525 fpm in 10 seconds. Find the total load of the rope. A. 12,086 lbs B. 14,086 lbs C. 16,086 D. 18, 086 lbs
2. The "dry" plate clutch is often used in automobile drivetrain applications to transmit power from the engine to the driving wheels. An illustration of the clutch is shown in Figure P2-12. Crankshaft spring constant, K Tin, Gin Tout, Oout Drivetrain inertia, Clutch friction, B Flywheel + Engine inertia, J, FIGURE P2-12 The input to the clutch is torque, Tins and the output is speed, 6 out- The impedances are based on torque as the flow variable and angle as potential variable. Speed is found by differentiating the poten- tial variable. a. Construct the impedance diagram and label all signals. b. Compute the transfer function Oout /e in 11-d D o
3 digits behind comma From the given figure, F = 100 N. • Draw the FBD 1000 mm F • Draw the action line of all forces that intersect in one point directly in the figure. Determine: 60° a) Force at smooth roll B b) Force at pin A Analytical solution. B. A 125 mm
or the spring system given in Figure 1, create the clement matrices as well as the global stiffness and force matrix, note that k-1. -ww- Figure 1
For the following problem please show intermediate steps including free body diagrams, equation used, problem setup etc. so that your approach can be followed. Finally please put the answer in a box with the appropriate unit.
QUESTION 6 Select the type of this mechanism below: L2 02 L3 А L1 C L4 O Crank-rocker O Triple rocker O Crank-crank O Slider-crank
Quantity Trial 1 Trial 2 F1 (dynes) 93100 dyn 102900 dyn F2 (dynes) 68600 dyn 107800 dyn F3 (dynes) 102900 dyn 117600 dyn F4 (dynes) 34300 dyn 78400 dyn On a separate sheet of paper or graphing paper, using polygon method (one for each trial), connect all the forces F1, F2, F3 and F4. What is the resultant force? What do you observe?
The forces shown in the following figure act on a specific screwed part. It can be noted that none of them acts directly on the known x and y axes. With this, what should be the force component acting on these axes? Options: a) The force on the x-axis is 20.54 N; and on the y-axis, it is 250.22 N. B) The force on the x-axis is -20.54 N; and on the y-axis, it is 230.22 N. c) The force on the x-axis is -22.54 N; and on the y-axis, it is 190.98 N. d) The force on the x-axis is 21.20 N; and on the y-axis, it is -234.89 N. e) The force on the x-axis is -20.54 N; and on the y-axis, it is 250.22 N.
The front landing gear for a mobile crane is shown in the above figure with the indicated main dimensions. Study it carefully, THEN: a) Make the product concept of fixing the hard rubber tire to its supporting Axle to ensure free running fit with its supporting axle. b) determine the limiting dimensions for the supporting axle with its tire's bore d) Design the L-Shaped supporting STEEL crank; according to "The von mises" failure criteria, if the resisting force p=42KN
The front landing gear for a mobile crane is shown in the above figure with the indicated main dimensions. Study it carefully, THEN: a) Make the product concept of fixing the hard rubber tire to its supporting Axle to ensure free running fit with its supporting axle. b) determine the limiting dimensions for the supporting axle with its tire's bore d) Design the L-Shaped supporting STEEL crank; according to "The von mises" failure criteria, if the resisting force p=42KN Please solve it ASAP not graphically by soildworks
1) Given the figure below, answer the following questions: a) What are the x and y components offorce F? (use Fx and Fy)b) What are the x and y components offorce P? (use Px and Py)(Hint: The x-y plane is differentfrom the true horizontal and verticalaxes)c) What are the vertical and horizontalcomponents of force F? (use Fh & Fv)d) What are the vertical and horizontalcomponents of force P? (use Ph & Pv)e) What is the magnitude of the resultant?f) What angle does the resultant make withthe horizontal axisg) What angle does the resultant makewith the inclined x-axis.