3 digits behind comma From the given figure, F = 100 N. • Draw the FBD 1000 mm • Draw the action line of all forces that intersect in one point directly in the figure. Determine: 60° a) Force at smooth roll B b) Force at pin A Analytical solution. B 125 mm

Q: the top view of a door that is 2.4m from the hinges.two equal forces with equal magnitude are…

A: Write the given data with suitable variables. r=2.4 m

Q: 70 400N 300N Figure (1)

A: Force is a vector quantity that has both magnitude and vector to signify its value. So, to get the…

Q: The tension is 850 lb in cable AB and 950 lb in cable AC. y B 45 in. Wood Floor 40 in. C 60 in. 65…

A:

Q: Problem 6: Values: A = 13 lb 0₁ = 20° 0₂ = 60° Use the figure shown on the right to complete the…

A:

Q: A 300 mm C 200 mm- B 0 D E 225 mm e perpendicular distance from point Eto the line of action

A: The Given information :The magnitude of the force Distance : To find :Perpendicular distance from…

Q: The resultant couple moment acting on the triangular block is to be zero. (Figure 1) Take F₁ = 15…

A:

Q: Consider the cable system shown in FIGURE P3-18 of the textbook. If: • e - 45° then, what is the…

A:

Q: 4- Find fx if fy is 1KHZ and number or horizontal tangencies is 2 and the vertical is 3.

A:

Q: Q1/ Find the resultant (R) and the direction (N) of the two forces shown in Figure below ? The angle…

A:

Q: 3-27-3-31. The forces shown form a couple. Replace the shown couple with an equivalent couple acting…

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute…

A: The answer is given in the below

Q: F = 100 lb F = 18 kips %3D 65 30° 750 70°

A: For solution refer below images.

Q: Need help with all four questions please. Include units all steps. Thanks.

A:

Q: Find the moment (Nm) caused by the force F = 934 N about point C if a = 25 mm and b = 37 mm. Round…

A: The clockwise moment is taken negative and the anticlockwise moment is taken positive. The…

Q: A bent tube is attached to a wall with brackets as shown.. A force of F = 450 lb is applied to the…

A: The force is The dimension are

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: FY F= 150 N a= 40 FX

A:

Q: Determine the angle θ (degrees).

A:

Q: Three forces are acting on the problem. List all of the simplifications that can be used in the…

A:

Q: 1. You are tasked to design a shaft for power transmission through a belt and pully at its right…

A: Given:To find:

Q: Looking for a handwritten solution. Include diagram and explanation. No gpt

A:

Q: oblem I. In a high-rise building construction, a boom is being used to efficiently transport…

A:

Q: 2. The crate weighs 450 kg and is supported by three cables as shown in the figure 2m below. 1m a.…

A:

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: Horizontal Component of the force at B: Vertical Component of the force at B: Horizontal Component…

A:

Q: For the following figure, draw a kinematic diagram for each identifying the point of interest. From…

A:

Q: Q// Determine the resultant force in figure bellow, and specify where it acts measured from point B.…

A:

Q: The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55…

A:

Q: Determine the magnitude and sense of the forces in bars A and B in the figure shown below. Show all…

A: Given data, A 80 k downward force is acting in a junction of bar A and B. To determine:- The…

Q: A wheel rest at the corner of the block as the figure. It F is a minimum force required to raise the…

A:

Q: The figure below shows a steel structure made up of two pre-assembled segments that are hoisted by a…

A:

Q: Determine the magnitude of the forces. In the given figure, V = 300 N, V2 = 1.6 m, and V3 = 11 m.…

A: V1=300NV2=1.6 mV3=11mconsidering FBD of joint Cconsidering force qulibirium along x dirction…

Q: The crane arm in the figure lifts the 95 kg mass at the end. When the angle BC piston makes with the…

A:

Q: The forces acting on a 1-ft length of a dam are shown in Figure 1-62. The upward ground reaction…

A: Given data as per the question Horizontal force at A side =12500 lb Vertical force =30000 lb The…

Q: 12. Draw the SFD and BMD for Figure 7 on the axes provided. Be sure to label the coordinates for the…

A:

Q: In the drawing, arm A is being driven back and forth in the direction of the arrows. It is connected…

A: Solution: Given Data: Screw B is lowered towards the end of arm A.   To Find: What happens to the…

Q: Q1: Find the result of the system of converging forces in Figure (1).

A:

Q: In earlier days, horses pulled barges down canals in the manner shown in the figure. Suppose the…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.