Provide step-by-step solution with complete given and formula to this problem. Draw sketch also. A mine hoist is to carry a cage loaded with ore at a total load of 8 tons. The depth of mine shaft is 328 ft. A 6 x 19 IPS wire rope with rope diameter of 1.75 in is to be use with sheave diameter of 39 in. The cage loaded is to start from rest and will attain a maximum velocity of 525 fpm in 10 seconds. Find the total load of the rope. A. 12,086 lbs B. 14,086 lbs C. 16,086 D. 18, 086 lbs

Provide step-by-step solution with complete given and formula to this problem. Draw sketch also. A mine hoist is to carry a cage loaded with ore at a total load of 8 tons. The depth of mine shaft is 328 ft. A 6 x 19 IPS wire rope with rope diameter of 1.75 in is to be use with sheave diameter of 39 in. The cage loaded is to start from rest and will attain a maximum velocity of 525 fpm in 10 seconds. Find the total load of the rope. A. 12,086 lbs B. 14,086 lbs C. 16,086 D. 18, 086 lbs

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Similar questions

A vertical mine hoist is to carry a cage loaded with ore at a total load of 8 metric tons. The depth of the main shaft is 100 meters. A 6 x 19 IPS wire rope with diameter of 44.5 mm is to be used for hoisting on a sheave 1.0 m diameter. The cage with load is to start from rest ans will attain a maximum velocity of 160 meters/min in 10 seconds. Find the factor of safety.
The larger and smaller pulleys of a chain block has 31 and 29 recesses respectively. If the efficiency is 45% when raising a load of 8kN, calculate, 6.1 the effort required 6.2 the effective distance through which the effort must move in order to lift the load 350 mm.
4. A pick-up truck that has a masa of 2.5 metric tons pulla a trailer with a mass of 1 metric ton. The engine of the truck has a pulling capacity of 5kN. The horizontal drawbar used to pull the trailer has a capacity of 600N only. If exceeded will disengage. If the full power of the engine is used wiill the horizontal draw bar disengage or not? Specify you answer if Yes or No explain based on your computation
Required Information Problem 04.007 - Simply supported T-shaped bracket - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A hand truck is used to move a compressed-air cylinder. Assume that the combined weight of the truck and cylinder is 220 lb. 22 in. w Ih 18 in. 10 in. Problem 04.007.c - Determining support reactions of a T-shaped bracket with variable spacing Determine the corresponding reaction at each of the two wheels. The corresponding reaction at each of the two wheels is Ib ICick to select)
Calculate the length of two springs when 35kg of mass is removed.
Based on the standard requirement of a system, it is given that the diameter of the bore ofcylinders for clamping and drilling processes are 100 mm and 80 mm, respectively. It isexpected that the clamping process will take a load of 700N while 650N will be loaded fordrilling process. The speed movement for the clamping and drilling process is designed to be120cm/min and 180mm/min, respectively.i. Compute the required flowrate for the pump for both clamping and drillingprocesses. ii. Calculate the working pressure required for the system if only one cylinder is tobe choose for both clamping and drilling processes. iii. Which horse power of the motor is required?
If in problem 2, the counterweight 100kg slides down, compute the magnitude of block W using the same date
The level of a common steelyard without hook connections weights 7kg and acts at 5cm to the left of the fulcrum. The hook which carries the load,weights 4kg and is also attached on the left-hand side of the fulcrum at a distance of 12cm.if graduation mark 72cm from the fulcrum reads 50kg. Find (a).the weight of rider (b). How far is the zero graduation from fulcrum (c).What is the movement of riderper kg of graduation?
The total length of a first class lever is 9.0 ft. This is used to move a load of 390 Ibs, as pictured below. How much effort must be applied? 18 in Your Answer: Answer
Five movable pulleys are arranged as in the first system of pulleys. If the efficiency of the system is 80%. Find the effort required to raise a load of 1000kg.
Draw a free body diagram. Include the free body diagram and your calculations in your work that you submit after the quiz. R C A A pulley has a negligible mass (that means, the radius is not relevant). It is supported with a pin at the center (and is free to rotate). A rope goes over the pulley. Block A, which has a mass of 7.388 kg is connected to one side of the rope. On the other side, Block B, with a mass of 17.455 kg is connected. The system is released from rest. What is the speed of block B, after B has traveled 0.350 m? Please enter a positive value in m/s (but without units) regardless of the direction of the motion of B.
Please help. This statics problem involves finding internal support forces on a frame. Thank you.