Thinking Like an Engineer: An Active Learning Approach (4th Edition)
4th Edition
ISBN: 9780134639673
Author: Elizabeth A. Stephan, David R. Bowman, William J. Park, Benjamin L. Sill, Matthew W. Ohland
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 8, Problem 72RQ
A 250-kilo-ohm [kΩ] resistor and a 0.2-microfarad [µF] capacitor rated at 250 volts [V] are connected in series, meaning that all of the current through the resistor enters the capacitor.
- a. Assuming that the capacitor is initially fully discharged and that a constant voltage of 5 volts [V] is maintained across the resistor, how long, in units of seconds [s], can this circuit operate before the voltage rating of the capacitor is exceeded?
- b. If the capacitor remains fixed at 0.2 microfarads [µF], to what value must the resistor be changed so that the rated capacitor voltage will not be exceeded for one minute [min]? Express your answer in ohms [Ω] using an appropriate SI prefix such that there are only one, two, or three digits shown to the left of the decimal.
- c. If the resistor remains fixed at 250 kilo-ohms [kΩ], to what value must the capacitor be changed so that the rated capacitor voltage will not be exceeded for one minute [min]? Express your answer in farad [F] using an appropriate SI prefix such that there are only one, two, or three digits shown to the left of the decimal.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A freezer of dimensions 4 m wide, 6 m long and 3 m high is under construction. The walls and ceiling are composed of 1.7 mm stainless steel (k = 15 W / [m ° C]), 10 cm thick foam insulation (k = 0.036 W / [m ° C]), certain thickness of corkboard (k = 0.043 W / [m ° C]), and 1.27 cm thick wood (k = 0.104 W / [m ° C]). The inside of the freezer is maintained at -30 ° C. The ambient air outside the freezer is 32 ° C. The convective heat transfer coefficient is 5 W / (m K) on wooden walls and 2 W / (m² K) on stainless steel surfaces. If the outside air has a dew point of 29 ° C, calculate the thickness of the corkboard insulation that will prevent moisture condensation on the outer walls of the freezer. Calculate the rate of heat transfer through the walls and ceiling of this freezer. Ignore heat transfer from floors and corners of buildings.
a. Thickness of corkboard insulation = Answercm.
b. Heat transfer rate through walls and ceilings = Answerwatt.
Air
A
Water
Calculate the gauge pressure, in kPa, at A, B, C, D in the reservoirs shown above.
(Note that the reservoirs between A and B are connected.)
Problem parameters:
h1 = 1.1 [m]
h2 = 0.3 [m]
h3 = 0.4 [m]
h4 = 0.5 [m]
Density of water is 1000 [kg/m³]; Density of air is 1.225 [kg/m³]; g = 9.81 [m/s²]
S.G. of oil is 0.89
h4 [m]
h3 [m]
h2 [m]
Air
B
h1 [m]
Oil
A freezer with dimensions of 4 m wide, 6 m long and 3 m high is under construction. The walls and ceiling are composed of 1.7 mm stainless steel (k = 15 W / [m ° C]), 10 cm thick foam insulation (k = 0.036 W / [m ° C]), a specific thickness of corkboard (k = 0.043 W / [m ° C]), and 1.8 cm thickness of wood (k = 0.104 W / [m ° C]). The inside of the freezer is maintained at -40 ° C. The ambient air outside the freezer is 32 ° C. The convective heat transfer coefficient is 5 W / (m K) on wooden walls and 2 W / (m² K) on stainless steel surfaces. If the outside air has a dew point of 29 ° C, calculate the thickness of the corkboard insulation that will prevent moisture condensation on the outer walls of the freezer. Calculate the heat transfer rate through the walls and ceiling of this freezer. Ignore heat transfer from floors and corners of buildings. a. Thickness of corkboard insulation = cm.
b. Heat transfer rate through walls and ceilings = watt.
Chapter 8 Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Ch. 8.1 - The engine on a spacecraft nearing Mars can...Ch. 8.2 - The mass of the human brain is 1360 grams [g]....Ch. 8.2 - The mass of the human brain is 1360 grams [g]....Ch. 8.3 - Convert 50 grams per cubic centimeter [g/cm3] into...Ch. 8.3 - A 75-gram [g] cylindrical rod is measured to be 10...Ch. 8.4 - Determine the mass in units of grams of 0.025...Ch. 8.4 - Determine the amount in units of moles [mol] of 5...Ch. 8.5 - The temperature of dry ice is 109.3 degrees...Ch. 8.5 - The specific heat capacity of copper is 0.09...Ch. 8.6 - If the pressure is 250 feet of water [ft H2O],...
Ch. 8.6 - A car tire is inflated to a gauge pressure of 35...Ch. 8.6 - An object is completely submerged in a liquid with...Ch. 8.7 - A 5-gallon [gal] container holds 35 grams [g] of...Ch. 8.7 - An 8-liter [L] container holds nitrogen (formula:...Ch. 8.8 - You push an automobile with a constant force of 20...Ch. 8.8 - One gram of material A is heated until the...Ch. 8.9 - A motor with a power of 100 watts [W] is connected...Ch. 8.10 - A motor with an input power of 100 watts [W] is...Ch. 8.10 - If a 50-kilogram [kg] load was raised 5 meters [m]...Ch. 8.11 - The current through a 12 kilo-ohms [k] resistor is...Ch. 8.11 - A device contains a 1000-ohm [] resistor with 120...Ch. 8.11 - A constant current transfers 12 1014 electrons...Ch. 8.11 - A 100-millihenry [mH] inductor has a current...Ch. 8.11 - Express 1LC in terms of base SI units, where L is...Ch. 8 - The space shuttle fleet was designed with two...Ch. 8 - Complete the following table assuming the object...Ch. 8 - Rank the following from largest mass to smallest...Ch. 8 - A typical American football weighs 14.5 ounces...Ch. 8 - The weight of the Hubble Space Telescope (HST) on...Ch. 8 - The value of gravitational acceleration on Earth,...Ch. 8 - Complete the following table: Density Compound...Ch. 8 - If the density of sodium is 98 kilograms per cubic...Ch. 8 - The specific gravity of iodine is 4.927. State the...Ch. 8 - Complete the following table. Assume you have a...Ch. 8 - Complete the following table. Assume you have a...Ch. 8 - Fluid A fills a one-gallon [gal] container and...Ch. 8 - A golden bar of metal (5 centimeters [cm] by 18...Ch. 8 - A lab reports the density of a new element is X...Ch. 8 - You have been hired as an intern for a plastics...Ch. 8 - A submersible robot is exploring one of the...Ch. 8 - Several students calculate the density of a gas,...Ch. 8 - You have been working to develop a new fictitious...Ch. 8 - Determine the mass in units of grams [g] of 0.35...Ch. 8 - A eutectic alloy of two metals contains the...Ch. 8 - Which of the following plastic has the highest...Ch. 8 - The outside air temperature of an airplane...Ch. 8 - The inside of an airplane is kept at 75 degrees...Ch. 8 - The Newton [N] temperature scale was devised by...Ch. 8 - In the Spring of 2004, NASA discovered a new...Ch. 8 - Is there a physical condition at which a...Ch. 8 - Complete the table: atmosphere pascal Inches of...Ch. 8 - If the pressure is 250 feet of water [ft H2O],...Ch. 8 - A normal blood pressure has a gauge pressure of...Ch. 8 - Prob. 30ICACh. 8 - If a force of 15 newtons [N] is applied to a...Ch. 8 - You wish to submerge an object in a liquid at sea...Ch. 8 - (a) Determine the maximum volume in gallons [gal]...Ch. 8 - A sensor is submerged in a silo to detect any...Ch. 8 - Complete the table, using the ideal gas law:...Ch. 8 - A 10-liter [L] flask contains 1.3 moles [mol] of...Ch. 8 - An ideal gas in a 1.25-gailon [gal] container is...Ch. 8 - An ideal gas is kept in a 10-liter [L] container...Ch. 8 - Football A is filled with 50 grams [g] of Gas X,...Ch. 8 - Determine the specific gravity of chlorine (Cl2)...Ch. 8 - Complete the table for specific heat conversions:...Ch. 8 - Which of the following requires the expenditure of...Ch. 8 - Which objectA, B, or Chas the most potential...Ch. 8 - Measurements indicate that boat A has twice the...Ch. 8 - A 10-gram [g] rubber ball is released from a...Ch. 8 - If a ball is dropped from a height (H) its...Ch. 8 - Eight hundred kilograms [kg] of paint solvent will...Ch. 8 - We go out to sunbathe on a warm summer day. If we...Ch. 8 - The specific heats of aluminum and iron are 0.214...Ch. 8 - Complete the table for thermal conductivity...Ch. 8 - The thermal conductivity of a plastic is 0.325...Ch. 8 - The heat transfer coefficient of steel is 25 watts...Ch. 8 - Complete the table. This problem involves the...Ch. 8 - When we drive our car at 100 feet per second...Ch. 8 - The power required by an airplane is given by P =...Ch. 8 - Complete the table. This problem involves the...Ch. 8 - A 100-watt [W] motor (60% efficient) is available...Ch. 8 - When boiling water, a hot plate takes an average...Ch. 8 - One problem with solar energy is that any given...Ch. 8 - Prob. 60ICACh. 8 - A resistor is dissipating 125 milliwatts [mW] of...Ch. 8 - An average cloud-to-ground lightning strike...Ch. 8 - Most electric stoves in the United States operate...Ch. 8 - A 3-volt [V] battery delivers a constant current...Ch. 8 - Prob. 65ICACh. 8 - A constant current charges a 20-nanofarad [nF]...Ch. 8 - Prob. 67ICACh. 8 - a. What is the average power, in units of watts...Ch. 8 - The National Football League specifies that all...Ch. 8 - A space probe is built with a mass of 1700...Ch. 8 - A person who has a weight of 165 pound-force [lbf]...Ch. 8 - A person who has a weight of 165 pound-force [lbf]...Ch. 8 - A person who has a weight of 165 pound-force [lbf]...Ch. 8 - The European Space Agency launched a probe called...Ch. 8 - The European Space Agency launched a probe called...Ch. 8 - The European Space Agency launched a probe called...Ch. 8 - The European Space Agency launched a probe called...Ch. 8 - A basketball has a mass of approximately 624 grams...Ch. 8 - A website you discover lists the density of a...Ch. 8 - Consider the following strange, but true, units: 1...Ch. 8 - Consider the following strange, but true, units: 1...Ch. 8 - A cube of material X, 1 inch [in] on all sides,...Ch. 8 - The density of gasoline is 0.72 grams per cubic...Ch. 8 - The Eco-Marathon is an annual competition...Ch. 8 - Prob. 17RQCh. 8 - Soccer is also called association football. A...Ch. 8 - A rod on the surface of Jupiters moon Callisto has...Ch. 8 - Prob. 20RQCh. 8 - Prob. 21RQCh. 8 - When an object is made of the plastic polyester...Ch. 8 - If we increase the temperature in a reactor by 90...Ch. 8 - If we increase the temperature in a reactor by 90...Ch. 8 - We are making a cup of coffee and want the...Ch. 8 - We want to construct a thermometer using mercury....Ch. 8 - A normal blood pressure has a gauge pressure of...Ch. 8 - The force on the inside of a cork in a champagne...Ch. 8 - One of the National Academy of Engineering Grand...Ch. 8 - A new gel is being developed to use inside padding...Ch. 8 - A 2-liter [L] soda bottle, made of PET, will fail...Ch. 8 - A storage tank is being designed for iodine. The...Ch. 8 - The specific gravity of honey is 1.43. A...Ch. 8 - NASA is designing a mission to explore Titan, the...Ch. 8 - Airspeed (v) is related to dynamic pressure using...Ch. 8 - When a flowing fluid is stopped, its pressure...Ch. 8 - A 10-liter [L] flask contains 5 moles [mol] of gas...Ch. 8 - A company that produces footballs uses a...Ch. 8 - A 5-liter [L] container holds nitrogen (formula:...Ch. 8 - A typical hot air balloon has a volume of 100,000...Ch. 8 - An ideal gas, kept in a 5-liter [L] container at...Ch. 8 - A container holding 1.5 moles [mol] of oxygen...Ch. 8 - A spacecraft is equipped with nine sensors,...Ch. 8 - A robotic rover on Mars finds a spherical rock...Ch. 8 - On February 15, 2013, Asteroid 2012 DA14 passed...Ch. 8 - If a 10-kilogram [kg] rotating solid cylinder...Ch. 8 - If a ball is dropped from a height its velocity...Ch. 8 - A bail is thrown vertically into the air with an...Ch. 8 - The maximum radius (R) a falling liquid drop can...Ch. 8 - A heat recovery system (HRS) is used to conserve...Ch. 8 - At noon on a clear day in midsummer, a cylindrical...Ch. 8 - In a factory, various metal cylinders are forged...Ch. 8 - A 3-kilogram [kg] projectile traveling at 100...Ch. 8 - Plutonium isotopes undergo decay, producing heat....Ch. 8 - The power required by an airplane is given by P =...Ch. 8 - When gasoline is burned in the cylinder of an...Ch. 8 - A spacecraft utilized Earths gravity and...Ch. 8 - A spacecraft is fueled using hydrazine (N2H4;...Ch. 8 - A 100-watt [W] motor (60% efficient) is used to...Ch. 8 - You need to purchase a motor to supply 400 joules...Ch. 8 - The Curiosity rover landed oil Mars on August 6,...Ch. 8 - A robotic rover on Mars finds a spherical rock...Ch. 8 - Consider the following strange, but true, unit: 1...Ch. 8 - When boiling water a hot plate takes an average of...Ch. 8 - Prob. 65RQCh. 8 - The power available from a wind turbine is...Ch. 8 - The computer system on the Indian Mars Orbiter...Ch. 8 - Prob. 68RQCh. 8 - Prob. 69RQCh. 8 - A 10,000-microfarad [F] capacitor is charged to 25...Ch. 8 - A 250,000-microfarad [F] capacitor is used to keep...Ch. 8 - A 250-kilo-ohm [k] resistor and a 0.2-microfarad...Ch. 8 - A 0.05-microfarad [F] capacitor discharges through...Ch. 8 - A variable capacitor has a range from 100...Ch. 8 - A constant voltage of 5 volts [V] is applied...Ch. 8 - A 20-millihenry [mH] inductor, a 0.5-mtcrofarad...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A freezer with dimensions of 4 m wide, 6 m long and 3 m high is under construction. The walls and ceiling are composed of 1.7 mm stainless steel (k = 15 W / [m ° C]), 15 cm thick foam insulation (k = 0.036 W / [m ° C]), specific thickness of corkboard (k = 0.043 W / [m ° C]), and 1.27 cm thick wood (k = 0.104 W / [m ° C]). The inside of the freezer is maintained at -40 ° C. The ambient air outside the freezer is 32 ° C. The convective heat transfer coefficient is 5 W / (m K) on wooden walls and 2 W / (m² K) on stainless steel surfaces. If the outside air has a dew point of 29 ° C, calculate the thickness of the corkboard insulation that will prevent moisture condensation on the outer walls of the freezer. Calculate the heat transfer rate through the walls and ceiling of this freezer. Ignore heat transfer from floors and corners of buildings. a. Thickness of corkboard insulation = Answer cm. b. Heat transfer rate through walls and ceiling = Answer watts.arrow_forward5. A building needs 30 [MWh] electricity annually for appliances, and its annual heating demand is 40 [MWh]. The building is connected to a heating grid (neglect the losses in the grid), where the heat comes from the waste heat from the power plant delivering the electricity to the building. What is the amount of primary energy used annually by the building? The power plant is combustion engine based, and has an electrical efficiency of 0.35 and a thermal efficiency of 0.55. (multiple choice, one answer) 25 [MWh] 57 [MWh] 63 [MWh] 86 [MWh] 177 [MWh]arrow_forwardA freezer of dimensions 4 m wide, 6 m long and 3 m high is under construction. The walls and ceiling are composed of 1.7 mm stainless steel (k = 15 W / [m ° C]), 10 cm thick foam insulation (k = 0.036 W / [m ° C]), a specific thickness of corkboard (k = 0.043 W / [m ° C]), and 1.27 cm thick wood (k = 0.104 W / [m ° C]). The inside of the freezer is maintained at -30 ° C. The ambient air outside the freezer is 32 ° C. The convective heat transfer coefficient is 5 W / (m K) on wooden walls and 2 W / (m² K) on stainless steel surfaces. If the outside air has a dew point of 29 ° C, calculate the thickness of the corkboard insulation that will prevent moisture condensation on the outside walls of the freezer. Calculate the heat transfer rate through the walls and ceiling of this freezer. Ignore heat transfer from floors and corners of buildings. a. Thickness of corkboard insulation = cm. b. Heat transfer rate through walls and ceiling = watts.arrow_forward
- A freezer with dimensions of 4 m wide, 6 m long and 3 m high is under construction. The walls and ceiling are composed of 1.7 mm stainless steel (k = 15 W / [m ° C]), 10 cm thick foam insulation (k = 0.036 W / [m ° C]), a specific thickness of corkboard (k = 0.043 W / [m ° C]), and 1.27 cm thick wood (k = 0.104 W / [m ° C]). The inside of the freezer is maintained at -30 ° C. The ambient air outside the freezer is 32 ° C. The convective heat transfer coefficient is 5 W / (m K) on wooden walls and 2 W / (m² K) on stainless steel surfaces. If the outside air has a dew point of 29 ° C, calculate the thickness of the corkboard insulation that will prevent moisture condensation on the outer walls of the freezer. Calculate the heat transfer rate through the walls and ceiling of this freezer. Ignore heat transfer from floors and corners of buildings. a. Thickness of corkboard insulation = cm. b. Heat transfer rate through walls and ceilings = watts.arrow_forwardA freezer with dimensions of 4 m wide, 5 m long and 3 m high is under construction. The walls and ceiling are composed of 1.7 mm stainless steel (k = 15 W / [m ° C]), 10 cm thick foam insulation (k = 0.036 W / [m ° C]), a specific thickness of corkboard (k = 0.043 W / [m ° C]), and 1.27 cm thick wood (k = 0.104 W / [m ° C]). The inside of the freezer is maintained at -35 ° C. The ambient air outside the freezer is 32 ° C. The convective heat transfer coefficient is 5 W / (m K) on wooden walls and 2 W / (m² K) on stainless steel surfaces. If the outside air has a dew point of 29 ° C, calculate the thickness of the corkboard insulation that will prevent moisture condensation on the outer walls of the freezer. Calculate the heat transfer rate through the walls and ceiling of this freezer. Ignore heat transfer from floors and corners of buildings. a. Thickness of corkboard insulation = Answer cm b. Heat transfer rate through walls and ceiling = Answer wattarrow_forwardThe tube, shown below, is supported by two cables (AB) and (AC). A force F = 600 lb is applied in cable AB. The component of the force F acting along cable (AC) is: |3 ft, E 8 ft В 12 ft 8 ft F 15 ft A Select one: a. 49.509 [lb] b. 495.708 [lb] c. 600 [lb] d. 459.708 [lb]arrow_forward
- A 3 kg particle is traveling at 7i+3j+4k [m/s]. An impulse acts on the particle via a force of 11i+-17j+13k [N] which acts for 0.4 seconds. 1. What is the speed of the particle in the i-direction after the impact? [m/s] 2. What is the speed of the particle in the j-direction after the impact? [m/s] 3. What is the speed of the particle in the k-direction after the impact? [m/s]arrow_forwardThis is part one of a two-part problem. Water flows through the turbine, condenser, pump and heat exchanger in the steam power cycle shown below. Hot air flows through the heat exchanger from state 5 to state 6 to heat the water before it enters the turbine. Using the values given in the figure below, determine the power output of the turbine, WT, in [kW]. Air = 1.004 kJ/kgK CPo,air %3D T6 = 400 K (6 (5 Heat Exchanger m = 5 kg/s T; = 1000 K 'air (1) w, Steam Power Cycle Turbine Wel= 50 kW %3D (3 2) Condenser =500 kW dundarrow_forwardThe force F (in newtons) of a hydraulic cylinder in a press is proportional to the square of sec x, where x is the distance (in meters) that the cylinder is extended in its cycle. The domain of F is [0, /3], and F(0) = 500. (a) Find F as a function of x. (b) Find the average force exerted by the press over the interval [0, /3]arrow_forward
- The walls of the refrigerated storage room are 10 m long and 3 m high and constructed with 90 mm concrete blocks (k = 0.935 W / [m ° C]) and 8 cm fiber insulation board (k = 0.048 W). / [m ° C]). The cold room temperature is -10 ° C and the convective heat transfer coefficient is 40 W / (m² K); the outside air temperature is 30 ° C with the outer wall surface convection heat transfer coefficient of 10 W / (m² K). Calculate the overall heat transfer coefficient. Overall heat transfer coefficient = Answer W / (m² K).arrow_forwardA cylindrical pipe with a cross-sectional radius r = 1.40[cm] is plunged into a l = 2.30[m] tall open water drum that is initially completely filled with water (pwater = 1000 [kg/m3]). The pipe goes h1 = 0.35 [m] above the drum before dropping down h2 = 3.50 [m] below the base of the drum as shown. The cross-sectional radius of the top side of the pipe is R = 2.20 [cm].A. How fast is the water going out of this pipe?B. What's the liquid's pressure at the top of the pipe? Assume that the system is exposed to 1.00 [atm] of air pressure.C. What's the maximum height the pipe can go above the drum before the water stops flowing out of the pipe? For liquid flow to be continuous, the liquid’s pressure must not fall before its vapor pressure. Assume that vapor pressure, in this case, is 2.30 [kPa].arrow_forwardA pendulum that is powered via a series elastic actuator can be modelled as follows (simplified): Jy (double dot) + By (dot) + K(y-u) + mglsin (y) where y is output and u is input = = 0 j = 0.2 [kgm^2] (Inertia) to XL. K = 60 [N.m/rad] (Spring stiffness) B 0.05 [N.m.s/rad] (damping coefficient) g 9.81 [m/s^2] (gravitational acceleration) m = 2.5 [kg] (mass) 1 0.5 [m] (pendulum length) = = yo = 0.25 [rad] y0 (dot) = -0.2 [rad/s] Simulate mechanical system using Matlab/Simulink when the input is a unit step Using a scope, plot the input and output.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY