Fluid Mechanics
8th Edition
ISBN: 9780073398273
Author: Frank M. White
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 9, Problem 9.22P
Given the pitot stagnation temperature and pressure and the static pressure measurements in Fig. P9.22, estimate the air velocity V. assuming (a) incompressible flow and (b) compressible flow.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Air, at stagnation conditions of 450 K and 250 kPa, flows through a nozzle. At section 1, where the area is 15 cm², there is a normal shock wave. If the mass flow is 0.4 kg/s, estimate (a) the Mach number and (b) the stagnation pres sure just downstream of the shock.
Compressible laminar fl ow, f≈ 64/Re, may occur in capillarytubes. Consider air, at stagnation conditions of 100°Cand 200 kPa, entering a tube 3 cm long and 0.1 mm indiameter. If the receiver pressure is near-vacuum, estimate(a) the average Reynolds number, (b) the Mach number atthe entrance, and (c) the mass flow in kg/h.
Consider the venturi nozzle of Fig. , with D = 5 cmand d = 3 cm. Stagnation temperature is 300 K, and theupstream velocity V1 = 72 m/s. If the throat pressure is124 kPa, estimate, with isentropic flow theory, (a) p1,(b) Ma2, and (c) the mass flow.
Chapter 9 Solutions
Fluid Mechanics
Ch. 9 - Prob. 9.1PCh. 9 - Prob. 9.2PCh. 9 - If 8 kg of oxygen in a closed tank at 200°C and...Ch. 9 - P9.4 Consider steady adiabatic airflow in a duct....Ch. 9 - Prob. 9.5PCh. 9 - Prob. 9.6PCh. 9 - Prob. 9.7PCh. 9 - Prob. 9.8PCh. 9 - P9.9 Liquid hydrogen and oxygen are burned in a...Ch. 9 - P9.10 A certain aircraft flics at 609 mi/h at...
Ch. 9 - Prob. 9.11PCh. 9 - Prob. 9.12PCh. 9 - Consider steam at 500 K and 200 kPa. Estimate its...Ch. 9 - Prob. 9.14PCh. 9 - Prob. 9.15PCh. 9 - Prob. 9.16PCh. 9 - Prob. 9.17PCh. 9 - Prob. 9.18PCh. 9 - Prob. 9.19PCh. 9 - Prob. 9.20PCh. 9 - P9.21 N?O expands isentropically through a duct...Ch. 9 - Given the pitot stagnation temperature and...Ch. 9 - Prob. 9.23PCh. 9 - Prob. 9.24PCh. 9 - Prob. 9.25PCh. 9 - Prob. 9.26PCh. 9 - P9.27 A pitot tube, mounted on an airplane flying...Ch. 9 - Prob. 9.28PCh. 9 - Prob. 9.29PCh. 9 - Prob. 9.30PCh. 9 - Prob. 9.31PCh. 9 - Prob. 9.32PCh. 9 - Prob. 9.33PCh. 9 - Prob. 9.34PCh. 9 - Prob. 9.35PCh. 9 - P9.36 An air tank of volume 1.5 m3 is initially at...Ch. 9 - Make an exact control volume analysis of the...Ch. 9 - Prob. 9.38PCh. 9 - Prob. 9.39PCh. 9 - Prob. 9.40PCh. 9 - Prob. 9.41PCh. 9 - Prob. 9.42PCh. 9 - Prob. 9.43PCh. 9 - Prob. 9.44PCh. 9 - It is desired to have an isentropic airflow...Ch. 9 - Prob. 9.46PCh. 9 - Prob. 9.47PCh. 9 - Prob. 9.48PCh. 9 - Prob. 9.49PCh. 9 - Prob. 9.50PCh. 9 - Prob. 9.51PCh. 9 - Prob. 9.52PCh. 9 - Prob. 9.53PCh. 9 - Prob. 9.54PCh. 9 - Prob. 9.55PCh. 9 - Prob. 9.56PCh. 9 - Prob. 9.57PCh. 9 - Prob. 9.58PCh. 9 - Prob. 9.59PCh. 9 - Prob. 9.60PCh. 9 - Prob. 9.61PCh. 9 - Prob. 9.62PCh. 9 - Prob. 9.63PCh. 9 - Prob. 9.64PCh. 9 - Prob. 9.65PCh. 9 - Prob. 9.66PCh. 9 - Prob. 9.67PCh. 9 - Prob. 9.68PCh. 9 - Prob. 9.69PCh. 9 - Prob. 9.70PCh. 9 - A converging-diverging nozzle has a throat area of...Ch. 9 - Prob. 9.72PCh. 9 - Prob. 9.73PCh. 9 - Prob. 9.74PCh. 9 - Prob. 9.75PCh. 9 - Prob. 9.76PCh. 9 - P9.77 A perfect gas (not air) expands...Ch. 9 - Prob. 9.78PCh. 9 - P9.79 A large tank, at 400 kPa and 450 K, supplies...Ch. 9 - Prob. 9.80PCh. 9 - Prob. 9.81PCh. 9 - Prob. 9.82PCh. 9 - 1*9.83 When operating at design conditions (smooth...Ch. 9 - Prob. 9.84PCh. 9 - A typical carbon dioxide tank for a paintball gun...Ch. 9 - Prob. 9.86PCh. 9 - Prob. 9.87PCh. 9 - Prob. 9.88PCh. 9 - Prob. 9.89PCh. 9 - Prob. 9.90PCh. 9 - Prob. 9.91PCh. 9 - Prob. 9.92PCh. 9 - Prob. 9.93PCh. 9 - Prob. 9.94PCh. 9 - Prob. 9.95PCh. 9 - Prob. 9.96PCh. 9 - Prob. 9.97PCh. 9 - Prob. 9.98PCh. 9 - Prob. 9.99PCh. 9 - Prob. 9.100PCh. 9 - Prob. 9.101PCh. 9 - Prob. 9.102PCh. 9 - Prob. 9.103PCh. 9 - Prob. 9.104PCh. 9 - Prob. 9.105PCh. 9 - Prob. 9.106PCh. 9 - Prob. 9.107PCh. 9 - Prob. 9.108PCh. 9 - P9.109 A jet engine at 7000-m altitude takes in 45...Ch. 9 - Prob. 9.110PCh. 9 - Prob. 9.111PCh. 9 - Prob. 9.112PCh. 9 - Prob. 9.113PCh. 9 - Prob. 9.114PCh. 9 - Prob. 9.115PCh. 9 - Prob. 9.116PCh. 9 - P9.117 A tiny scratch in the side of a supersonic...Ch. 9 - Prob. 9.118PCh. 9 - Prob. 9.119PCh. 9 - Prob. 9.120PCh. 9 - Prob. 9.121PCh. 9 - Prob. 9.122PCh. 9 - Prob. 9.123PCh. 9 - Prob. 9.124PCh. 9 - Prob. 9.125PCh. 9 - Prob. 9.126PCh. 9 - Prob. 9.127PCh. 9 - Prob. 9.128PCh. 9 - Prob. 9.129PCh. 9 - Prob. 9.130PCh. 9 - Prob. 9.131PCh. 9 - Prob. 9.132PCh. 9 - Prob. 9.133PCh. 9 - P9.134 When an oblique shock strikes a solid wall,...Ch. 9 - Prob. 9.135PCh. 9 - Prob. 9.136PCh. 9 - Prob. 9.137PCh. 9 - Prob. 9.138PCh. 9 - Prob. 9.139PCh. 9 - Prob. 9.140PCh. 9 - Prob. 9.141PCh. 9 - Prob. 9.142PCh. 9 - Prob. 9.143PCh. 9 - Prob. 9.144PCh. 9 - Prob. 9.145PCh. 9 - Prob. 9.146PCh. 9 - Prob. 9.147PCh. 9 - Prob. 9.148PCh. 9 - Prob. 9.149PCh. 9 - Prob. 9.150PCh. 9 - Prob. 9.151PCh. 9 - Prob. 9.152PCh. 9 - Prob. 9.153PCh. 9 - Prob. 9.154PCh. 9 - Prob. 9.155PCh. 9 - Prob. 9.156PCh. 9 - The Ackeret airfoil theory of Eq. (9.104) is meant...Ch. 9 - Prob. 9.1WPCh. 9 - Prob. 9.2WPCh. 9 - Prob. 9.3WPCh. 9 - Prob. 9.4WPCh. 9 - Prob. 9.5WPCh. 9 - Prob. 9.6WPCh. 9 - Prob. 9.7WPCh. 9 - Prob. 9.8WPCh. 9 - FE9.1 For steady isentropic flow, if the absolute...Ch. 9 - FE9.2 For steady isentropic flow, if the density...Ch. 9 - Prob. 9.3FEEPCh. 9 - Prob. 9.4FEEPCh. 9 - Prob. 9.5FEEPCh. 9 - Prob. 9.6FEEPCh. 9 - Prob. 9.7FEEPCh. 9 - Prob. 9.8FEEPCh. 9 - Prob. 9.9FEEPCh. 9 - Prob. 9.10FEEPCh. 9 - Prob. 9.1CPCh. 9 - Prob. 9.2CPCh. 9 - Prob. 9.3CPCh. 9 - Prob. 9.4CPCh. 9 - Prob. 9.5CPCh. 9 - Prob. 9.6CPCh. 9 - Professor Gordon Holloway and his student, Jason...Ch. 9 - Prob. 9.8CPCh. 9 - Prob. 9.1DPCh. 9 - Prob. 9.2DP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q2: Helium, at T. = 400 K, enters a nozzle isentropically. At section 1, where Aj = 0.1 m, a pitot-static arrangement (see Fig. Q2) measures stagnation pressure of 150 kPa and static pressure of 123 kPa. Estimate (a) M1; (b) T;; (c) mass flow; and (d) A*. Take y = 1.66 and R = 2077 J/(kg K). Air at 100 K Mercury Ans. (a) 0.5; (b) 370 K; (c) 9.03 kg/s; and (d) 0.0756 m2.arrow_forwardCompute stagnation enthalpy of air at normal conditions (P=1atm, T=300K) moving with velocity of 1398 m/s. What temperature of air we will observe?arrow_forwardHelium, at T0 = 400 K, enters a nozzle isentropically. Atsection 1, where A1 = 0.1 m2, a pitot-static arrangement(see Fig. P9.25) measures stagnation pressure of 150 kPaand static pressure of 123 kPa. Estimate (a) Ma1, (b) massfl ow m # , (c) T1, and (d ) A*.arrow_forward
- A large tank, at 500 K and 200 kPa, supplies isentropicairfl ow to a nozzle. At section 1, the pressure is only 120kPa. What is the Mach number at this section?(a) 0.63, (b) 0.78, (c) 0.89, (d ) 1.00, (e) 1.83 assume one-dimensional fl ow of ideal air, R 5287 J/(kg ? K) and k 5 1.4.arrow_forwardA gas, assumed ideal, flows isentropically from point 1,where the velocity is negligible, the pressure is 200 kPa,and the temperature is 300°C, to point 2, where the pressureis 40 kPa. What is the Mach number Ma2 if the gas is(a) air, (b) argon, or (c) CH4? (d ) Can you tell, withoutcalculating, which gas will be the coldest at point 2?arrow_forwardAir at P1 = 1 MPa, T1 = 600 °C and V1 = 150 m/s enters a converging nozzle. The exit area is A2 = 50 cm2 and the back pressure is P2 = 0.7 MPa. What is the mass flow rate (kg/s) through the nozzle? What the is Mach number at the nozzle exit? What would be the flow rate you calculate if you assumed isothermal flow?arrow_forward
- a) A convergent nozzle with a given area ratio is supplied with air at a constant stagnation pressure Poand a constant stagnation temperature To. With the aid of a sketch plot the nozzle mass flow rate as a function of pressure ratio () across P the nozzle. In your answer indicate the critical value of the pressure ratio. For air you may assume y = 1.4 and R = 287J/kg K. b) The engine of a supersonic aircraft is equipped with a convergent-divergent nozzle. A A, A -4.0).Determine the design subsonic and supersonic Mach numbers for this area ratio. You may assume the combustion products have the same properties as air and the expansion process through the nozzle is isentropic. The nozzle's area ratio is ( c) Determine at what pressure ratios ( ) a normal shock wave appears in the P divergent part of the nozzle at a location where -3.0) Aheck A₁arrow_forwardAir, at stagnation conditions of 500 K and 200 kPa, flows through a nozzle. At section 1, where the area is 12 cm², the density is 0.32 kg/m³. Assuming isentropic flow, (a) find the mass flow. (b) Is the flow choked? If so, estimate A*. Also estimate (c) p₁ and (d) Ma₁.arrow_forwardhe reservoir pressure and temperature for a Laval nozzle are 5 atm [abs] and 520 K,respectively. The flow is isentropically expanded to supersonic speed at the nozzle exitwith area Ae = 4in2. If the exit-to-throat area ratio is 2.295, calculate the followingexit properties: d) ρe; e) p0,e; f) T0,e; gamma = 1.4, R = 287 Please show all work!!arrow_forward
- Air, at stagnation conditions of 450 K and 250 kPa, fl owsthrough a nozzle. At section 1, where the area is 15 cm2,there is a normal shock wave. If the mass fl ow is 0.4 kg/s,estimate (a) the Mach number and (b) the stagnation pressurejust downstream of the shock.arrow_forwardAir flows at high speed through a Herschel venturi monitoredby a mercury manometer, as shown in Fig. .The upstream conditions are 150 kPa and 80°C. Ifh = 37 cm, estimate the mass flow in kg/s. (Hint: The flowis compressible.)arrow_forwardFor given air flow with Mach number in test section (i.e. at CD nozzle exit), Me = 8, T01 = 300 K, pressure in test section = 4000 Pa. (1) What is the value of static temperature, stagnation temperature and stagnation pressure in the test section? (2) What is the value of stagnation pressure in the storage thank? (3) What do you conclude about state of air? (4) What is the solution to rectify this problem. i.e. (5)What is the minimum temperature of air should you take in reservoir tank? At this condition, what is mass flow rate in test section? Low pressure air chamber High pressure air storage Storage tank T01 = 300K P01 = ? Settling chamber Pressure regulator Nozzle Screens Test-section Pe = 4000 Pa Me = 8 Te = ? K Sonic throat P0e =? T0e = ? Blow down wind Tunnel (Open circuit type) Diffuser Second throat vacuum tankarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License