Sustainable Energy
2nd Edition
ISBN: 9781337551663
Author: DUNLAP, Richard A.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 7P
To determine
Find the maximum wavelength of the light that produces voltage in a CdS photovoltaic device
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A beam of light passes from glass with refractive index 1.58 into water with a refractive index 1.33. The
angle of the refracted ray in water is 58.0°.
a) Draw a sketch of the situation showing the interface between the media, the normal line, the incident
ray, the reflected ray, the refracted ray, and the angles of these rays relative to the normal line.
b) Calculate the angle of incidence in the glass.
A 2 x 2 m flat plate solar collector for domestic hot water heating is shown in the figure. The incident solar radiation on the glass cover, which transmits 90% of the incident flux, is 750 W/m2. Water flows through the tubes soldered to the backside of the absorber plate, entering at a temperature of 25°C. The temperature of the glass cover is 27°C, and it radiates heat with an emissivity of 0.92 to the sky at –50°C. Additionally, the glass cover losses heat by convection to air at 20°C flowing over its surface at 30 km/h. Assume that the radiation heat transfer between the absorber plate and glass cover and the heat transfer through the back and sides of the collector is negligible.
An optical source has a spectral width of 1 nm. What type of optical source is it
likely to be?
Coherent source
Wideband source
Incoherent source
Incandescent lamp
All of these
None of these
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- enumerate 5 examples of sound- reflecting materials (solid materials)arrow_forwardMass = Density*volumearrow_forwardA micrometer is connected to the movable mirror of an interferometer. When the micrometer is tightened down on a thin metal foil, the net number of bright fringes that move, compared to closing the empty micrometer, is 296. What is the thickness of the foil? The wavelength of light used is 589 nm.arrow_forward
- In the figure is shown:arrow_forwardi) What is a photovoltaic cell? ii) A certain solar cell type has an output capability of 0.5 A at 0.4Volts. A series / parallel solar array has been designed of such cells with 80 parallel strings and each string has 1500 cells in series. Calculate: (i) Voltage capability (ii) Current capability and (iii) Power output capability of the array.arrow_forward51 Material Science and Engineeringarrow_forward
- 13.arrow_forwardA laser (light amplification by stimulated emission ofradiation) provides a coherent (in-phase) nearly monochromaticsource of high-intensity light. Lasers are used in eye surgery,CD/DVD players, basic research, etc. Some modern dye laserscan be “tuned” to emit a desired wavelength. Fill in the blanks inthe following table of the properties of some common lasersarrow_forwardA poorly designed electronic device has two bolts attached to different parts of the device that almost touch each other in its interior as in the figure. The steel and brass bolts are at different electric potentials, and if they touch, a short circuit will develop, damaging the device. The initial gap between the ends of the bolts is d = 5.0 mm at 27°C. At what temperature will the bolts touch? Assume the distance between the walls of the device is not affected by the temperature change. Steel 0000000 0.010 m 0.030 m Brass 5.0 μmarrow_forward
- 3.) A classroom is 30 ft by 30 ft with a 12 ft ceiling. You want to determine the average illuminance on the floor from recessed luminaires. What is the RCR value that you will use to determine the appropriate luminaire CU? RCR =arrow_forward1. An unknown lamp placed 6m from a photometer screen provides the same illuminance as a 90 cd lamp placed 4 m from the screen. What is the candlepower of the unknown lamp? 2. The illuminance of a room 20 ft x 15 ft is being designed. The illuminance required is 50 footcandles. What is the total required lumens output of the lamp assuming room and luminaire efficiency of 42%?arrow_forwardWhat is the effect of temperature on surface conduction of any material?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage LearningResidential Construction Academy: House Wiring (M...Civil EngineeringISBN:9781285852225Author:Gregory W FletcherPublisher:Cengage Learning
- Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning
Residential Construction Academy: House Wiring (M...
Civil Engineering
ISBN:9781285852225
Author:Gregory W Fletcher
Publisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning