Concept explainers
The unknown parameters using Kirchhoff’s Laws.
Answer to Problem 1PP
ES1= 12 V | E1= 0.89 V | E2= 20.89 V | E3= 11.1 V |
ES2= 32 V | I1= 1.31 mA | I2= 20.89 mA | I3= 22.2 mA |
R1= 680 Ω | R2=1000 Ω | R3=500 Ω |
Explanation of Solution
We will use Kirchhoff’s Voltage law to solve for the unknown parameters.
Consider two loops LOOP 1 and LOOP 2 with their respective loop currents I1 and I2
Using KVL in loop 1,
Using KVL in loop 2,
From equation (1), we can write I2as ,
Substitute this expression for I2in equation (2),
Substitute the value of I1 in equation (3).
CurrentI3 is the sum of currents I1 and I2
The voltage drops are obtained by using Ohm’s Law,
The results are summarized in the figure below,
Want to see more full solutions like this?
Chapter 9 Solutions
EBK DELMAR'S STANDARD TEXTBOOK OF ELECT
- What is the relation between length of span and sag?: a. sag is directly proportional to square of span b. sag is inversely proportional to squareroot of span C. sag is inversely proportional to square of span d. sag is directly proportional to squareroot of spanarrow_forwardThe active component of line current in figure 1 is______. a. 12A b. 20A c. 12A d. 4Aarrow_forwardQ4arrow_forward
- Calculate element and welding currents with mesh analysis.arrow_forwardPlease answer in typing formatarrow_forward17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…arrow_forward
- A Moving to another question will save this response. Question 4 What is the approximate value of surge impedance of a power cable ? 400 100 40 1600 A Moving to another question will save this response.arrow_forwardThe following are the correct sign conventions for analyzing circuits using Kirchhoff's Laws EXCEPT: For travel direction from negative to positive terminal, the emf should be positive. For travel direction from positive to negative terminal, the emf should be negative. For travel direction opposite to current direction, the voltage drop across the resistor should be negative. For travel direction same as the current direction, the voltage drop across the resistor should be negative.arrow_forwardMechanical connections are shown with ____. a straight broken lines b a connection dot c a connection node d lines crossing each otherarrow_forward
- EBK ELECTRICAL WIRING RESIDENTIALElectrical EngineeringISBN:9781337516549Author:SimmonsPublisher:CENGAGE LEARNING - CONSIGNMENTElectricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage LearningPower System Analysis and Design (MindTap Course ...Electrical EngineeringISBN:9781305632134Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. SarmaPublisher:Cengage Learning