Steel Design (Activate Learning with these NEW titles from Engineering!)
6th Edition
ISBN: 9781337094740
Author: Segui, William T.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 8, Problem 8.5.1P
To determine
The maximum load on the weld in kips per inch of length.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Determine the lengths of the side fillet welds required at the heel and toe of the angle shown.
Allowable shearing stress through the throat of each weld is 124 MPa.
L 150 x 150 x 13
L1
P1
108
T= 250 kN
42
13
150 mm
P2+
L2
gusset plate
150
Plate is connected to the column using fillet welds as shown. The size of weld is 12 mm.
Determine the following:
Locate the center of gravity of the weld group from the vertical part of the weld.
Stress due to moment.
Max stress due to combined moment and load.
100KN
4
100mm
55mm
150mm
55mm
110mm
3
Determine the size of the weld using E60 electrode. Dead Load = 38 kip and LL = 95 kips (Service Loads)
10 in-
10 in-
-10 in
W = ?
Chapter 8 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
Ch. 8 - Prob. 8.2.1PCh. 8 - Prob. 8.2.2PCh. 8 - A plate is used as a bracket and is attached to a...Ch. 8 - Prob. 8.2.4PCh. 8 - Prob. 8.2.5PCh. 8 - Prob. 8.2.6PCh. 8 - Prob. 8.2.7PCh. 8 - Prob. 8.2.8PCh. 8 - Prob. 8.2.9PCh. 8 - Prob. 8.2.10P
Ch. 8 - Prob. 8.2.11PCh. 8 - Prob. 8.2.12PCh. 8 - Prob. 8.2.13PCh. 8 - Prob. 8.3.1PCh. 8 - Prob. 8.3.2PCh. 8 - Prob. 8.3.3PCh. 8 - Prob. 8.3.4PCh. 8 - Prob. 8.3.5PCh. 8 - Prob. 8.3.6PCh. 8 - Prob. 8.3.7PCh. 8 - Prob. 8.3.8PCh. 8 - Prob. 8.3.9PCh. 8 - Prob. 8.3.10PCh. 8 - Use an elastic analysis and determine the maximum...Ch. 8 - Use an elastic analysis and determine the maximum...Ch. 8 - Use an elastic analysis and determine the maximum...Ch. 8 - Prob. 8.4.4PCh. 8 - Prob. 8.4.5PCh. 8 - Prob. 8.4.6PCh. 8 - Use an elastic analysis and compute the extra load...Ch. 8 - Use an elastic analysis and compute the extra load...Ch. 8 - Prob. 8.4.9PCh. 8 - Prob. 8.4.10PCh. 8 - Prob. 8.4.11PCh. 8 - Prob. 8.4.12PCh. 8 - Prob. 8.4.13PCh. 8 - Prob. 8.4.14PCh. 8 - Prob. 8.4.15PCh. 8 - Prob. 8.4.16PCh. 8 - Prob. 8.4.17PCh. 8 - Prob. 8.4.18PCh. 8 - a. Use LRFD and design a welded connection for the...Ch. 8 - Prob. 8.4.20PCh. 8 - Prob. 8.5.1PCh. 8 - Prob. 8.5.2PCh. 8 - Prob. 8.5.3PCh. 8 - Prob. 8.5.4PCh. 8 - Prob. 8.5.5PCh. 8 - Prob. 8.6.1PCh. 8 - Prob. 8.6.2PCh. 8 - Prob. 8.6.3PCh. 8 - Prob. 8.6.4PCh. 8 - Prob. 8.7.1PCh. 8 - Prob. 8.7.2PCh. 8 - Prob. 8.7.3PCh. 8 - Prob. 8.8.1PCh. 8 - Prob. 8.8.2PCh. 8 - Prob. 8.8.3PCh. 8 - Prob. 8.8.4P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).arrow_forwardUse an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.arrow_forwardUse an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.arrow_forward
- 3.2 A load is applied 100 kN inclined at 30 to vertical in clockwise direction, check whether the weld is safe. Fillet weld of size 6 mm used in shop welding. 320 X y 140 140 X 240 mm 309 Parrow_forwardSolve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of 185 kN applied along its centroidal axis. The maximum size of fillet weld that can be used in 8mm and the allowable shear stress of 94 MPa. Determine the lengths of the side fillet welds if a transverse fillet weld is added at the end of the angle. 71 mm 185 KN 29 mmarrow_forwardA 4 x 4 x ½ - in. angle of A36 steel is to be welded to a plate with E70XX electrodes to develop the full tensile strength of the angle. Using 3/8-in. fillet welds, compute the design lengths for the welds on the two sides of angle, assuming development of tension on the full cross section of the angles. GIVEN: A = 3.75 in2 L1 = 10.94” L2 = 5.09” IF only connected leg, L = 7.7”; 4.75 each sidearrow_forward
- A welded bracket connection is shown in figure. It supports a factored load of 150 kN at a distance of 120 mm from the face of column. Design the fillet weld on two sides. Grade of steel = Fe410, f. = 250 MPa. y 120 mm P₁ = 150 kN Fillet weld t = 12 mmarrow_forwardCalculate the maximum shear force in the welds in the given figure. P=160kN X = 150mm y= 125mm z=70mm 4 Y Narrow_forwardIf the structural frame is replaced to structural steel and the connections is to be designed, determine the following Determine the centroid of the weld measured from the given origin A. Determine the direct shear load in the welds. Determine the required size of the fillet weld(E60xx) if the maximum resultant load is 750,000 N/mmarrow_forward
- A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back of the channel. All steel is A36 with Fy=250 MPa and Fu=400 MPa. Use E70electrodes having and Fu=485 MPa (SMAW) process. The maximum length of lap is 250mm. The size of fillet weld is 8mm. Assume the width of slot weld is 22 mm. Size of slot weld is 13mm Properties of C250x37 A = 4750 mm2 tw = 13.0 mm2 d = 254 mm a. Determine the force resisted by the slot weld in kN, when the full tensile capacity is 712.5 KN (from the gross yielding capacity using ASD) Hint: Full tensile Capacity = Force Resisted by Fillet and Slot Weld Round your answer to 3 decimal places.arrow_forwardThe connection is shown in Fig. 3. Two cover plates are applied to connect the steel plates by fillet welds. The dimensions of connection are presented in Fig. 3. The leg size of fillet weld hr is 10 mm. Q235 steel, f-215 N/mm2, E43 electrode, fav=160N/mm?. Calculate the load-carrying capacity of the fillet weld connection wwww. (Note: the strength of steel plate should be calcualted. (Unit: mm) 220 ス20 091arrow_forwardA hanger is suspended from a plate that is welded to a wide flange beam as shown. The plate requires a 1”x1” chamfer in the inside corners to clear the fillet radius of the beam. A ¼ inch double sided fillet weld is used with no welds placed at 1”x1” from the inside corners as shown in the weld configuration. Determine the maximum load the hanger can carry using ASD and the Elastic method if the eccentricityof the load from beam centerline is 7”.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning