Sustainable Energy
2nd Edition
ISBN: 9781337551663
Author: DUNLAP, Richard A.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 8, Problem 12P
a.
To determine
Find the power transferred through a iron rod.
b.
To determine
Find the diameter of the rod after reducing from 10 cm towards reducing the power transferred to the rod is 4 W.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A certain parallel-plate capacitor is filled with a dielectric for which K = 6.50. The area of each plate is 0.0524 m², and the plates are
separated by 2.97 mm. The capacitor will fail (short out and burn up) if the electric field between the plates exceeds 179 KN/C. What is
the maximum energy that can be stored in the capacitor?
Number i
!
Units
J
PROBLEM 6.12 The cross-sectional areas of solid shaft of diameter
400 mm and hollow shaft of internal diameter 300 mm of same material are
equal. Find the ratio of power transmitted by the two shafts at the same
speed.
509% Part (b) Consider a 5.0om long wire of mass 10.0 g. The wire is suspended between the poles of a magnet as shown (end view of wire). When a 0.7 A current in the wire is turned on,
the wire and magnet are attracted to each other.
wire
What can you learn about the magnet and the direction of the current through the wire with this information?
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A flat sheet is in the shape of a rectangle with sides of lengths 0.400 m and 0.600 m. The sheet is immersed in a uniform electric field of magnitude 60.0 N/C that is directed at 20° from the plane of the sheet (Figure 1). Figure 20% 0.400 m * -0.600 m- 1 of 1 Part A Find the magnitude of the electric flux through the sheet. Express your answer with the appropriate units. O Þ= 4.9 μA 4 m² N с ? The compound unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again.arrow_forwardMotor unit A is used to elevate the 300-kg, cylinder at a constant rate of 2 m/s. If the power meter B registers an electrical input of 2.10 kW, calculate the combined electrical and mechanical efficiency e of the system. 1 B 100 kg A lee 300 kg 2 m/sarrow_forwardThe propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 6 MW when the shaft rotates at 26 rad/sec. Determine the angle of twist in the shaft radian. G = 75 GPa. Note round off your answer in three decimal placesarrow_forward
- A storage tank is connected to a piping system as illustrated in Figure P1. Water at temperature of 20°C in the storage tank flows through a piping system with the pipe's diameter of 5 cm and discharges from a nozzle to the atmospheric at velocity of 3.5 m/s. The diameter of the nozzle is 3cm. Galvanized pipe is used and installed in this piping system. All the fitting components installed in this system such as regular 90° and tees are flanged type. The Water at 20°C 21 m D= 5 cm d- 3 cm After 5 years of operation, the accumulation of the dirt and other micro particles stained on the pipe's wall surface have significantly reduced the water discharge from the nozzle. Please explain this phenomenon.arrow_forwardA well-insulated turbine operating at steady state is shown on the right. Steam enters at 3 MPa, 400°C, with a volumetric flow rate of 85 m³/min. Some steam is extracted from the turbine at a pressure of 0.5 MPa and a temperature of 180°C. The rest expands to a pressure of 6 kPa and a quality of 90%. The total power developed by the turbine is 11,400 kW. Kinetic and potential energy effects can be neglected. Determine (a) the mass flow rate (in kg/s) at each exit, and (b) the diameter of the duct, d₂ (in cm) where steam is extracted P₁ = 3MPa T₁=400°C (AV)₁ = 85 m³/min Turbine P2 = 0.5 MPa T₂ = 180°C V₂= 20 m/s Power out ¹3 P3= 6 kPa x3 = 90%arrow_forwardThe horizontal pump in Fig.1 discharges water at 57 m3/h. Neglecting Losses,What power in KW is delivered to the water by the pump? A-836 watt B-8360 watt C-8362 watt D-83600 wattarrow_forward
- Use an steel tape of length 20 m and a cross-section area of 5 mm 2 and weighing 1.5 kg in , Use the tape by placing it suspended under a tension of 5 kg to measure a distance of 506 m at a temperature of 40 degrees Celsius. the coefficient of linear expansion (a) 0.000018 meters / degree Celsius and it has been placed at a temperature of 20 degrees Celsius under a standard tension of 2.5 kg. Calculate the real distance using the elastic modulus of steel 106 kg / cm?. Q4/arrow_forwardQ- If the energy present in a jet of water of 20 cm diameter and having a velocity of 25 m/s could be extracted by a device with 90% efficiency. Find the power extracted. (Assume 1/2g=0.051 sec²/m)arrow_forwardQuestion 36 2 Points Cells are connected in series to increase the voltage output. Blank 1 v is the total voltage if the three (3) cells below are connected in series. Tisv Tisv Tisv 1.5 V 1.5 V 1.5 V Blank 1 Add your answerarrow_forward
- 2. A parallel-plate capacitor initially has a capacitance of 100 F. What will be the capacitance if the distance between the plates is doubled?arrow_forwardA 150-mm-diameter jet of water is discharging from a nozzle into the air at a velocity of 45 m/s. Find the power in the jet with respect to a datum at the jet.arrow_forward(a) A storage tank is connected to a piping system as illustrated in Figure P1. Water at temperature of 20°C in the storage tank flows through a piping system with the pipe's diameter of 5 cm and discharges from a nozzle to the atmospherie at velocity of 3.5 m/s. The diameter of the nozzle is 3cm. Galvanized pipe is used and installed in this piping system. All the fitting components installed in this system such as regular 90° and tees are flanged type. The Water at 20°C 21 m D= 5 cm d = 3 cm Figure P1 i. By using suitable assumptions, predict the friction factor of this piping system (Including the Moody Chart is necessary).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
