Applied Physics (11th Edition)
11th Edition
ISBN: 9780134159386
Author: Dale Ewen, Neill Schurter, Erik Gundersen
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 7.2, Problem 28P
The crane shown in Fig. 7.27 is supporting a load of 11,500 N. Find the tension in the supporting cable and the compression in the boom.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The 4.00 m boom is uniform and weighs 2550 N. Find the tension in the guy wire and the force exerted on the boom at its lower end.
A uniform plank of length 2.00 m and mass 26.0 kg is supported by three ropes, as indicated by the blue vectors in the figure below. Find the tension in each rope when a 710–N person is d = 0.500 m from the left end. Answer the 3 boxes below:
The horizontal boom supporting a lamp is of uniform construction and weighs 50 N. If the lamp weighs 150 N, what is the tension in the supporting cable?
Chapter 7 Solutions
Applied Physics (11th Edition)
Ch. 7.1 - Find the sum of each set of forces acting at the...Ch. 7.1 - 703 N (right); 829 N (left); 125 N (left); 484 N...Ch. 7.1 - Forces of 225 N and 175 N act at the same point....Ch. 7.1 - Three forces with magnitudes of 225 N, 175 N, and...Ch. 7.1 - Prob. 5PCh. 7.1 - Find the sum of each set of vectors. Give angles...Ch. 7.1 - If forces of 1000N acting in a northerly direction...Ch. 7.1 - If two forces of 100N and 50.0 N, respectively,...Ch. 7.1 - Find the sum of each set of vectors. Give angles...Ch. 7.1 - Prob. 10P
Ch. 7.1 - Prob. 11PCh. 7.1 - Find the sum of each set of vectors. Give angles...Ch. 7.1 - Forces of F1 = 1150 N, F2 = 875 N, and F3 = 1450 N...Ch. 7.1 - Four forces, each of magnitude 2750 lb, act at the...Ch. 7.2 - Find the force F that will produce equilibrium in...Ch. 7.2 - Find the force F that will produce equilibrium in...Ch. 7.2 - Find the force F that will produce equilibrium in...Ch. 7.2 - Find the force F that will produce equilibrium in...Ch. 7.2 - Find the force F that will produce equilibrium in...Ch. 7.2 - Find the force F that will produce equilibrium in...Ch. 7.2 - Five persons are having a tug-of-war. Kurt and...Ch. 7.2 - A certain wire can support 6450 lb before it...Ch. 7.2 - The frictional force of a loaded pallet in a...Ch. 7.2 - A bridge has a weight limit of 7.0 tons. How heavy...Ch. 7.2 - A tractor transmission weighing 260N and a...Ch. 7.2 - A skid loader lifts a compressor weighing 672 N...Ch. 7.2 - Find the forces F1 and F2 that produce equilibrium...Ch. 7.2 - Find the forces F1 and F2 that produce equilibrium...Ch. 7.2 - Find the forces F1 and F2 that produce equilibrium...Ch. 7.2 - Find the forces F1 and F2 that produce equilibrium...Ch. 7.2 - Find the forces F1 and F2 that produce equilibrium...Ch. 7.2 - Find the forces F1 and F2 that produce equilibrium...Ch. 7.2 - A rope is attached to two buildings and supports a...Ch. 7.2 - A rope is attached to two buildings and supports a...Ch. 7.2 - If the angles between the horizontal and the ropes...Ch. 7.2 - Find the tension in the horizontal supporting...Ch. 7.2 - Find the tension in the horizontal supporting...Ch. 7.2 - An automobile of mass 1550 kg is towed at a steady...Ch. 7.2 - A vehicle that weighs 16,200 N is parked on a 20.0...Ch. 7.2 - Find the tension in the cable and the compression...Ch. 7.2 - The crane shown in Fig. 7.26 is supporting a load...Ch. 7.2 - The crane shown in Fig. 7.27 is supporting a load...Ch. 7.3 - Given:F=16.0lbr=6.00ft=?Ch. 7.3 - Given:F=100Nr=0.420m=?Ch. 7.3 - Prob. 3PCh. 7.3 - Prob. 4PCh. 7.3 - Given:=65.4Nmr=35.0cmF=?Ch. 7.3 - Given:F=630Nr=74.0cm=?Ch. 7.3 - If the torque on a shaft of radius 2.37 cm is 38.0...Ch. 7.3 - If a force of 56.2 lb is applied to a torque...Ch. 7.3 - A motorcycle head bolt is torqued to 25.0 N m....Ch. 7.3 - A force of 112 N is applied to a shaft of radius...Ch. 7.3 - A torque of 175 lb ft is needed to free a large...Ch. 7.3 - A torque wrench reads 14.5 N m. If its length is...Ch. 7.3 - The torque on a shaft of radius 3.00 cm is 12.0 N...Ch. 7.3 - An engine bolt is torqued to 30.0 N m. If the...Ch. 7.3 - A mower bolt is torqued to 65.0 N m. If the length...Ch. 7.3 - An automobile bolt is torqued to 27.0 N m. If the...Ch. 7.3 - A torque wrench reads 25 lb ft. (a) If its length...Ch. 7.3 - If 13 N m of torque is applied to a bolt with an...Ch. 7.3 - If the torque required to loosen a nut on the...Ch. 7.3 - If the torque required to loosen a nut on the...Ch. 7.3 - A truck mechanic must loosen a rusted lug nut. If...Ch. 7.3 - An agricultural mechanic tries to loosen a nut on...Ch. 7.4 - Find the force F that will produce equilibrium for...Ch. 7.4 - Find the force F that will produce equilibrium for...Ch. 7.4 - Find the force F that will produce equilibrium for...Ch. 7.4 - Find the force F that will produce equilibrium for...Ch. 7.4 - Find the force F that will produce equilibrium for...Ch. 7.4 - Find the force F that will produce equilibrium for...Ch. 7.4 - Find the force F that will produce equilibrium for...Ch. 7.4 - Find the force F that will produce equilibrium for...Ch. 7.4 - Prob. 9PCh. 7.4 - A 5000-lb truck is 20.0 ft from one end of a...Ch. 7.4 - Prob. 11PCh. 7.4 - An auto transmission of mass 165 kg is located...Ch. 7.4 - A bar 8.00 m long supports masses of 20.0 kg on...Ch. 7.4 - Two painters, each of mass 75.0 kg, stand on a...Ch. 7.4 - Two painters, one of mass 75.0 kg and the other...Ch. 7.4 - Two painters stand on a 10.00-m scaffold. One, of...Ch. 7.4 - An auto differential with a mass of 76.0 kg is...Ch. 7.4 - Prob. 18PCh. 7.5 - Solve for F1 : 30.0F1 = (14.0)(18.0) +...Ch. 7.5 - Solve for Fw : (12.0)(15.0) + 45.0Fw =...Ch. 7.5 - Two workers carry a uniform 15.0-ft plank that...Ch. 7.5 - Juan and Pablo carry a load weighing 720 N on a...Ch. 7.5 - A wooden beam is 3.30 m long and has its center of...Ch. 7.5 - An auto engine weighs 650lb and is located 4.00 ft...Ch. 7.5 - A bridge across a country stream weighs 89,200 N....Ch. 7.5 - A window washers scaffold 12.0 ft long and...Ch. 7.5 - A porch swing weighs 29.0 lb. It is 4.40 ft long...Ch. 7.5 - Prob. 10PCh. 7.5 - A bridge has a mass of 1.60 104 kg, is 21.0 m...Ch. 7.5 - A uniform steel beam is 5.00 m long and weighs 360...Ch. 7.5 - A wooden pole is 4.00 m long, weighs 315 N, and...Ch. 7.5 - A bridge has a mass of 2.60 104 kg, is 32.0 m...Ch. 7.5 - An auto engine of mass 295 kg is located 1.00 m...Ch. 7.5 - A 125-kg horizontal beam is supported at each end....Ch. 7.5 - Prob. 17PCh. 7.5 - The uniform bar in Fig. 7.49 is 5.00 m long and...Ch. 7.5 - Find the magnitude, direction, and placement (from...Ch. 7.5 - Find the magnitude, direction, and placement (from...Ch. 7 - Concurrent forces act at a. two or more different...Ch. 7 - The resultant force is a. the last force applied....Ch. 7 - A moving object a. can be in equilibrium. b. is...Ch. 7 - The study of an object in equilibrium is called a....Ch. 7 - Torque is a. applied force in rotational motion....Ch. 7 - The first condition of equilibrium states that a....Ch. 7 - In the second condition of equilibrium. a....Ch. 7 - The center of gravity of an object a. is always at...Ch. 7 - Is motion produced every time a force is applied...Ch. 7 - Prob. 10RQCh. 7 - Define equilibrium.Ch. 7 - In what direction does the force due to gravity...Ch. 7 - What may be said about concurrent forces whose sum...Ch. 7 - What is a force diagram?Ch. 7 - Is the length of the pedal necessarily the true...Ch. 7 - In your own words, explain the second condition of...Ch. 7 - What is the primary consideration in the selection...Ch. 7 - List three examples from daily life in which you...Ch. 7 - Is the center of gravity of an object always at...Ch. 7 - Prob. 20RQCh. 7 - Find the sum of the following forces acting at the...Ch. 7 - Forces of 275 lb and 225 lb act at the same point....Ch. 7 - Prob. 3RPCh. 7 - Prob. 4RPCh. 7 - Prob. 5RPCh. 7 - Forces of F1 = 1250 N, F2 = 625 N, and F3 = 1850 N...Ch. 7 - Eight people are involved in a tug-of-war. The...Ch. 7 - A bridge has a weight limit of 14.0 tons. What is...Ch. 7 - The x-components of three vectors are Fx, 375...Ch. 7 - If Wy=600N and Wx=900N, what are the magnitude and...Ch. 7 - Find forces F1 and F2 that produce equilibrium in...Ch. 7 - Prob. 12RPCh. 7 - Find the tension in the cable and the compression...Ch. 7 - Find the tension in each cable in Fig. 7.51.Ch. 7 - Find the tension in each cable in Fig. 7.52.Ch. 7 - Find the tension and the compression in Fig. 7.53.Ch. 7 - A man is changing a flat tire using a tire iron...Ch. 7 - A torque of 81.0 lb ft is produced by a torque arm...Ch. 7 - A hanging sign has mass 200kg. If the tension in...Ch. 7 - A scaffold supports a bricklayer and bricks...Ch. 7 - Two ladders at the ends of a scaffold support a...Ch. 7 - How far from the light end of a 68.0-cm bat would...Ch. 7 - A bridge has mass 8000kg. If a 3200-kg truck stops...Ch. 7 - If the truck in Problem 23 stops 7.00 m from one...Ch. 7 - A uniform 2.20-kg steel bar with length 2.70 m is...Ch. 7 - Find the vertical force needed to support the...Ch. 7 - A horizontal cable supports the boom of a crane....Ch. 7 - Archeologists in Egypt are attempting to open a...Ch. 7 - Sean and Greg are on a job site standing on two...Ch. 7 - Maria has severe arthritis and can apply a maximum...Ch. 7 - Kristas flagpole bracket is mounted at an angle of...Ch. 7 - Prob. 5AC
Additional Science Textbook Solutions
Find more solutions based on key concepts
* Evaluation question You find the following in a report about blackouts: "The acceleration that causes blackou...
College Physics
Questions 25 through 27 concern a classic figure-skating jump called the axel. A skater starts the jump moving ...
College Physics: A Strategic Approach (4th Edition)
Rooms A and B are the same size, and are connected by an open door. Room A, however, is warmer (perhaps because...
An Introduction to Thermal Physics
21. Two -diameter aluminum electrodes are spaced apart.
The electrodes are connected to a battery.
...
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
3. What is free-fall, and why does it make you weightless? Briefly describe why astronauts are weightless in th...
The Cosmic Perspective
A pair of sound waves of different wavelengths reaches the listeners ear as shown. Which has the highest pitch:...
Conceptual Integrated Science
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- One end of a uniform beam that weighs 3.50 ✕ 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in the figure below. Find the tension in the cable. (Assume ?1 = 20° and ?2 = 37°.) Note: The answer is 244 N but I have no idea how to get there. Any help would be appreciated. Thanks.arrow_forwardIn the wheelbarrrow, the load has a perpendicular lever arm of 7.5 cm, while the hands have a perpendicular lever arm of 1.02m. (a) what upward force must you exert to support the whellbarrow and its load if their combined mass is 45kg? (b) what force does the wheelbarrow exert on the ground?arrow_forward20° 60° 2. A 10,000 N weight is supported by a cable attached to a massless beam, 4 m long, that can pivot at its base. The beam is stabilized by a second cable attached to a wall. It settles in the position shown on the left, where the weighted cable is vertical, the second cable is 20⁰ from horizontal, and the beam is 60° from horizontal. Find the tension in the second cable and the horizontal and vertical reaction forces at the W base of the beam.arrow_forward
- In the wheelbarrow, the load has a perpendicular lever arm of 7.50 cm, while the hands have a perpendicular lever arm of 1.02 m. (a) What upward force must you exert to support the wheelbarrow and its load if their combined mass is 45.0 kg? (b) What force does the wheelbarrow exert on the ground?arrow_forwardA rod extends horizontally from a wall. It’s attached to the wall by a bolt at one end, and a wire at the other, as shown. A “SALE” sign hangs from the center of the rod. The rod has W(rod) = 200.0 N and length 3.00 m. The sign has W(sign) = 100.0 N. Find the tension in the wire reported in Newtons.arrow_forwardA 1,100-N uniform boom at y = 56.5° to the horizontal is supported by a cable at an angle 0 = 33.5° to the horizontal as shown in the figure below. The boom is pivoted at the bottom, and an object of weight w = 2,150 N hangs from its top. 0 e Pivot W (a) Find the tension in the support cable. KN (b) Find the components of the reaction force exerted by the pivot on the boom. (Assume the positive x-direction is to the right and the positive y-direction is upward. Include the sign of the value in your answer.) horizontal component kN vertical component KNarrow_forward
- The 4.00 m boom is uniform and weighs 2550 N. Find the tension in the guy wire and the force exerted on the boom at its lower end. 30° 1.75m 2225 N 55°arrow_forwardA uniform drawbridge must be held at a 37° angle abovethe horizontal to allow ships to pass underneath. The drawbridge weighs45,000 N and is 14.0 m long. A cable is connected 3.5 m from thehinge where the bridge pivots (measured along the bridge) and pullshorizontally on the bridge to hold it in place. What is the tension in the cable?arrow_forwardFind the horizontal and vertical components of the reaction force of the support (the connection at the wall) and the tension in the cable. The beam has a mass of 200 kg and a length of 6 m. The support wire is connected to the middle of the beam and is fastened to the wall 3m above the support. The weight hanging at the end of the beam has a mass of 300 kg.arrow_forward
- Two steel balls, A and B, are balanced on a beam with negligible mass as shown below. Compute for length x if the mass of ball B is 28 kg and the vertical force exerted by the pin support to the beam is 578 N. Express the answers in meter.arrow_forwardA shelf bracket is mounted on a vertical wall by a single screw. S S2 S1 Neglecting the weight of the bracket, and if s = 6.4 cm, s1 the horizontal force component exerted on the bracket by the screw when a 95.2 N vertical force is applied as shown. Imagine that the bracket is slightly loose. 5.4 cm and s2 = 2.2 cm, find =arrow_forwardConsider a horizontal forearm. On one end of the forearm is the elbow, and on the other end is the hand. The forearm has a mass of 2.08 kg. The distance from the elbow to the hand is 39.7 cm. If the biceps muscle connects to the forearm a distance of 4.73 cm from the elbow, and the biceps muscle can supply a maximum force of 1.417E+3 N (with the forearm in a horizontal position), what is the maximum mass (in kg) that the person can hold?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON
College Physics
Physics
ISBN:9781305952300
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
University Physics (14th Edition)
Physics
ISBN:9780133969290
Author:Hugh D. Young, Roger A. Freedman
Publisher:PEARSON
Introduction To Quantum Mechanics
Physics
ISBN:9781107189638
Author:Griffiths, David J., Schroeter, Darrell F.
Publisher:Cambridge University Press
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Lecture- Tutorials for Introductory Astronomy
Physics
ISBN:9780321820464
Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina Brissenden
Publisher:Addison-Wesley
College Physics: A Strategic Approach (4th Editio...
Physics
ISBN:9780134609034
Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart Field
Publisher:PEARSON
What Is Circular Motion? | Physics in Motion; Author: GPB Education;https://www.youtube.com/watch?v=1cL6pHmbQ2c;License: Standard YouTube License, CC-BY