Steel Design (Activate Learning with these NEW titles from Engineering!)
6th Edition
ISBN: 9781337094740
Author: Segui, William T.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 7, Problem 7.4.3P
To determine
(a)
The number of bolts using Load and Resistance Factor Design (LRFD).
To determine
(b)
The number of bolts using Allowable Strength Design (ASD).
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Determine the design tensile strength of the 12
in. x 1/2 in. steel plate shown in the figure. The
bolts are 3/4 in. diameter. The steel is A572 Gr.
50. Check yielding and fracture. Check Block
Shear.
T
3in.
73im 13in 1 3in t
A double-angle shape is shown in the figure. The steel is
A36, and the holes are for 2-inch-diameter bolts.
Assume that A₂ = 0.75An.
Ae
1
2
Determine the design tensile strength for LRFD.
Determine the allowable strength for ASD.
CIVIL ENGINEERING
- STEEL DESIGN
AL
Section
2L5 x 3 x 516 LLBB
3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates
of the same width with half the thickness by 24mm diameter bolts, as shown. The
rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36
steel with yield strength F,-248MPa and ultimate strength F,-400MPa.
a. Determine the design strength of the section.
b. Determine the allowable strength of the section
24mm
30mm
Chapter 7 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
Ch. 7 - Prob. 7.3.1PCh. 7 - Prob. 7.3.2PCh. 7 - Prob. 7.4.1PCh. 7 - Prob. 7.4.2PCh. 7 - Prob. 7.4.3PCh. 7 - Prob. 7.4.4PCh. 7 - Prob. 7.4.5PCh. 7 - Prob. 7.4.6PCh. 7 - Prob. 7.6.1PCh. 7 - Prob. 7.6.2P
Ch. 7 - Prob. 7.6.3PCh. 7 - Prob. 7.6.4PCh. 7 - Prob. 7.6.5PCh. 7 - Prob. 7.6.6PCh. 7 - Prob. 7.7.1PCh. 7 - Prob. 7.7.2PCh. 7 - Prob. 7.7.3PCh. 7 - Prob. 7.8.1PCh. 7 - Determine the adequacy of the hanger connection in...Ch. 7 - Prob. 7.9.1PCh. 7 - Prob. 7.9.2PCh. 7 - Prob. 7.9.3PCh. 7 - Prob. 7.9.4PCh. 7 - Prob. 7.9.5PCh. 7 - Prob. 7.11.1PCh. 7 - Prob. 7.11.2PCh. 7 - Prob. 7.11.3PCh. 7 - Prob. 7.11.4PCh. 7 - Prob. 7.11.5PCh. 7 - Prob. 7.11.6PCh. 7 - Prob. 7.11.7PCh. 7 - Prob. 7.11.8PCh. 7 - Prob. 7.11.9PCh. 7 - Prob. 7.11.10P
Knowledge Booster
Similar questions
- The plate with dimension 18 mm x 400 mm (thickness by width) is to be connected to a gusset plate using 6-Ø24 mm bolts in arrange in 3 row (2 each row) along the x-axis. The plate is to be design for tension. Using A36 steel and assuming A= An. Use NSCP 2015. a. Compute the design strength considering yielding and tensile rupture. (LRFD} b. Compute the allowable strength considering yielding and tensile rupture. (ASD)arrow_forwardThe splice plates shown in Figure 2 are 1/2-inch-thick. How many 7/8-inch-diameter, Group B bolts are required? The given load consists of 30% dead load and 70% live load. A36 steel is used. Threads are not excluded from the shear plane. 90 k Figure 2 a. Use LRFD. b. Use ASD. % in. 90 karrow_forwardThe plate with dimension 18 mm x 400 mm (thickness by width) is to be connected to a gusset plate using 6-Ø24 mm bolts in arrange in 3 row (2 each row) along the x-axis. The plate is to be design for tension. Using A36 steel and assuming Ae= An. Use NSCP 2015. a. Compute the design strength considering yielding and tensile rupture. (LRFD) b. Compute the allowable strength considering yielding and tensile rupture. (ASD)arrow_forward
- A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.arrow_forwardThe bolts in the lap joint shown are 22mm in diameter and 25mm diameter holes. The plates are A36 steel with Fy = 250MPa and Fu = 400Mpa. For this problem, x1 = 500mm, x2 = 160mm, x3 = 60mm and t = 12mm. The allowable stresses are: Bearing Stress on projected area of the plates Fp = 1.5Fu Tension on net area of plates, Ft = 0.5Fu Shear on plates, Fy= 0.3Fu Shear strength of bolt, Fv= 210 Mpa a.) Determine the value of P based on bolt shear b.) Determine the value of load P based on bearing on projected area on plate (area in contact with the plate and bolts) c.) Determine the value of P based on block shear (use net area for block shear and use the diameter of hole)arrow_forwardA 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.arrow_forward
- Five bolts are used in the connection between the axial member and the support. The ultimate shear strength of the bolts is 300 MPa, and a factor of safety of 4.2 is required with respect to fracture. Determine the minimum allowable bolt diameter required to support an applied load of P = 325 kN. Answer: dmin mmarrow_forwardTwo plates each with thickness t = 16 mm are bolted together with 6 – 22 mm diameter bolts forming a lap connection. Bolt spacing are as follows: S1 = 40 mm, S2 = 80 mm, S3 = 100 mm. Bolt hole diameter = 25 mm. Using A36 steel having Fy = 248 MPa and Fu = 400 MPa. P P S - P S2 S2 DETERMINE: 1. Determine the allowable load Pa based on bearing at bolt holes. (ASD) 2. Determine the ultimate load Pu based on block shear.arrow_forwardA L 3 x 2 x ¼ is connected to a gusset plate via six bolts. The nominal diameter of the bolt is 0.25 inches, the pitch spacing is 1.75 inches, the gage spacing is 2 inches, and the thickness of the connection is (¼) inch. The yield stress is 50 Ksi and the ultimate stress is 60 Ksi. Consider section line (a-a') for the analysis. . a. What is the effective net area (Ae) of the angle section in inches2 [a-a']?(The shear lag factor is "0.80") b. What is the design tensile yielding strength in Kips for the steel member? c. What is the design tensile rupture strength in Kips for the steel member? d. What is the minimum Factor of Safety if a tensile load of 23 Kips is applied to the angle section? please make sure the answer is correct 100% I only need the final answersarrow_forward
- Problem 2 A tension plate shown below is used to support suspended load "T. Gusset Plate F, = 248 MPa Fu = 400 MPa 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm, (Assume weld strength is satisfactory).-arrow_forwardA 10mm x 150 mm plate of A36 steel (Fy = 248 MPa & Fu = 400 MPa) is used as a tension member. It is connected using 20 mm Ø bolts. U=1.0 a. Determine the tensile capacity based on yielding (ASD & LRFD) b. Determine the tensile capacity based on rupture (ASD & LRFD) c. Determine the tensile capacity based on block shear strength (ASD & LRFD) 75mm 37.5 75 75 75 87.5arrow_forwardPlate A, PL 16mm x 375mm, is connected to another plate B with 10- 22 mm o bolts as shown. The steel is A36 steel with Fy= 250 MPa and F,= 400 MPa. Assume that plate B has adequate strength. Use ASD. Plate B 375a 75 m 2 75mm Plate A 75 mm 75mm 150 50150 Compute the nominal strength based on yielding in KN.O Determine the allowable tensile strength of Plate A in KN.O Compute the allowable tensile strength at section a-1-2-2-4-c in KN.0arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning