Plate A, PL 16mm x 375mm, is connected to another plate B with 10- 22 mm o bolts as shown. The steel is A36 steel with Fy= 250 MPa and F,= 400 MPa. Assume that plate B has adequate strength. Use ASD. Plate B ... 375a 75 m 2 75mm Plate A 75 mm 75mm 150 50150 Compute the nominal strength based on yielding in KN.O Determine the allowable tensile strength of Plate A in KN.0 Compute the allowable tensile strength at section a-1-2-2-4-c in KN.0

Plate A, PL 16mm x 375mm, is connected to another plate B with 10- 22 mm o bolts as shown. The steel is A36 steel with Fy= 250 MPa and F,= 400 MPa. Assume that plate B has adequate strength. Use ASD. Plate B ... 375a 75 m 2 75mm Plate A 75 mm 75mm 150 50150 Compute the nominal strength based on yielding in KN.O Determine the allowable tensile strength of Plate A in KN.0 Compute the allowable tensile strength at section a-1-2-2-4-c in KN.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

.
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
Please correct answer otherwise dislike
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld