Electronics Fundamentals: Circuits, Devices & Applications
8th Edition
ISBN: 9780135072950
Author: Thomas L. Floyd, David Buchla
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Question
Chapter 7, Problem 13P
To determine
The cause of the pointer in the given motor to deflect when the current is present in the coil.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Explain Coriols meter in detail.
Horizontal Controls
Autoset
Vertical Controls
Trigger Controls
Describe what does the following controls of the oscilloscope do.
lo lo jo
What are the two necessary conditions for a thyristor to begin conduction?and Once a thyristor begins to conduct, what condition(s) is necessary to cease conduction? Also, why is the conduction angle greater with an inductive load than with a purely resistive load?
Chapter 7 Solutions
Electronics Fundamentals: Circuits, Devices & Applications
Ch. 7 - The tesla (T) and the gauss (G) are both units for...Ch. 7 - The unit for measuring magnetomotive force (mmf)...Ch. 7 - Ohm’s law for a magnetic circuit gives the...Ch. 7 - A solenoid is a form of electromagnetic switch...Ch. 7 - A hysteresis curve is a plot of flux density (B)...Ch. 7 - To produce an induced voltage in a coil, the...Ch. 7 - Prob. 7TFQCh. 7 - Prob. 8TFQCh. 7 - Prob. 9TFQCh. 7 - Prob. 10TFQ
Ch. 7 - Prob. 1STCh. 7 - Prob. 2STCh. 7 - Prob. 3STCh. 7 - Prob. 4STCh. 7 - Prob. 5STCh. 7 - Prob. 6STCh. 7 - Prob. 7STCh. 7 - The electromagnetic activation of a movable shaft...Ch. 7 - When there is current through a wire placed in a...Ch. 7 - Prob. 10STCh. 7 - Prob. 11STCh. 7 - Prob. 12STCh. 7 - Prob. 13STCh. 7 - Prob. 14STCh. 7 - Prob. 15STCh. 7 - The cross-sectional area of a magnetic field is...Ch. 7 - In a certain magnetic field the cross-sectional...Ch. 7 - Wha is the flux in a magnetic material when the...Ch. 7 - At a given location, the earth’s magnetic field...Ch. 7 - A very strong permanent magnet has a field of...Ch. 7 - Prob. 6PCh. 7 - What is the relative permeablility of a...Ch. 7 - Determine the reluctance of a material with a...Ch. 7 - What is the magnetomotive force in a 500 turn coil...Ch. 7 - Typically, when a solenoid is activated, is the...Ch. 7 - Prob. 11PCh. 7 - Explain the sequence of events in the circuit of...Ch. 7 - Prob. 13PCh. 7 - What is the magnetizing force in Problem 9 if the...Ch. 7 - How can the flux density in Figure 7-51 be changed...Ch. 7 - In Figure 7-51, determine the following if the...Ch. 7 - Determine from the hysteresis curves in Figure...Ch. 7 - According to Faraday’s law, what happens to the...Ch. 7 - The voltage induced across a certain coil is...Ch. 7 - Prob. 20PCh. 7 - A 20 cm long conductor is moving upward between...Ch. 7 - Prob. 22PCh. 7 - If a generator is 80% efficient and delivers 45 W...Ch. 7 - Prob. 24PCh. 7 - If the output voltage in Problem 24 is 14 V, what...Ch. 7 - Prob. 26PCh. 7 - Prob. 27PCh. 7 - A basic one-loop de generator is rotated at 60...Ch. 7 - Assume that another loop of wire. 90 from the...
Knowledge Booster
Similar questions
- For the figure shown below if the current is moving clockwise around the coil. Which direction does the coil rotate? S O The whole coil moves down. The whole coil moves up. The right side goes down, and the left side goes up. The right side goes up, and the left side goes down.arrow_forwardElectromagnetcsarrow_forwardPre-Laboratory Assignment 1-) What are the basic purposes of using an oscilloscope and a multimeter? 2-) What is the difference between AC and DC coupling? 3-) What is the purpose of the trigger systemin the oscilloscope? 4-) Draw the following signals: a-) 5 sin 2n1000t b-) 3cos2n500t +3arrow_forward
- V₁ 12 In the figure shown, what is the peak to peak voltage of V1 if the vertical sensitivity of the oscilloscope is 0.25 V/Div* HIPNHHHH ALLarrow_forwardWith the aid of diagrams, discuss the procedure to detect zero error and cyclic error in fieldwork.arrow_forwardWhy is it desirable to wait 1 s after a potential pulse before recording the current in voltammetry?arrow_forward
- TECNO OO SPARKarrow_forwardDraw the charging and discharging waveform if the switch changed position precisely when the capacitor reached 5 time constants when charging and discharging.arrow_forwardGiven the context of the inductive stroke method.Can the polarity of the voltage be the same the moment the switch is closed and then open? Why?arrow_forward
- 1. What are the two necessary conditions for a thyristor to begin conduction? 2. Once a thyristor begins to conduct, what condition(s) is necessary to cease conduction? 3. Why is the conduction angle greater with an inductive load than with a purely resistive load?arrow_forwardFill in the blanks: Given the model for position control system, find the value for K1 and K2 so that the peak time is equal to 0.5 s and the %OS is equal to 3%. K1= 93.2070 K2= 0.129 I 446 23arrow_forwardThe wavelorm displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 50 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (1) amplitude of waveform Q, (ii) peak to peak value of waveform P, (111) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. 主 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P (iii) Frequency of waveform P =arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
