Fluid Mechanics
8th Edition
ISBN: 9780073398273
Author: Frank M. White
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.4P
When tested in water at 20°C flowing at 2 m/s, an 8-cm- diameter sphere has a measured drag of 5 N. What will be the velocity and drag force on a 1.5-m-diameter weather balloon moored in sea-level standard air under dynamically similar conditions?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
b) When tested in water at 20°C flowing at 2_m'sAlan 8 cm diameter sphere has a measured
drag force of 5 N. Determine the velacity and drag force ony l,5 n diåmeter weather balloon
moored in sea-level standard air under dyhamidally 'similar conditions? For sea-level
standard air, take p = 1.2255 kg/m² ànd u» 1.78 x 10-5kg/m·s
A wind tunnel is being used to study the aerodynamics of a full-scale model rocket that is 30 cm long. Scaling for drag calculations are based on the Reynolds number. The rocket hasan expected maximum velocity of 190 km/h. What is the Reynolds number at this speed? Assume ambient air is at 20°C. The wind tunnel is capable of speeds up to 160 km/h; so an attempt is made to improve this top speed by varying the air temperature. Calculate the equivalent speed for the wind tunnel using air at 5°C and 65°C. Would replacing air with carbon dioxide provide higher equivalent speeds?
Fluid Mechanics Problem:
A ship is 150 m long and has a wetted area of 5000 m2.If it is encrusted with barnacles, the ship requires 7000 hp to overcome friction drag when moving in seawater at 15 kn and 20oC. What is the average roughness of the barnacles? How fast would the ship move with the same power if the surface were smooth? Neglect wave drag.
Note:
Treat the ship hull as a flat plate. Use eq. 7.48b to find effective barnacle roughness height.Use equation (7.45) White for the drag coefficient CD = D/.5pV2A , where A is the hull (plate) area, to find the ship velocity for smooth plate.
Chapter 5 Solutions
Fluid Mechanics
Ch. 5 - Prob. 5.1PCh. 5 - A prototype automobile is designed for cold...Ch. 5 - P5.3 The transfer of energy by viscous dissipation...Ch. 5 - When tested in water at 20°C flowing at 2 m/s, an...Ch. 5 - P5.5 An automobile has a characteristic length and...Ch. 5 - P5.6 The disk-gap-band parachute in the...Ch. 5 - Prob. 5.7PCh. 5 - Prob. 5.8PCh. 5 - The Richardson number, Ri, which correlates the...Ch. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - The Stokes number, St, used in particle dynamics...Ch. 5 - Prob. 5.13PCh. 5 - Flow in a pipe is often measured with an orifice...Ch. 5 - The wall shear stress T in a boundary layer is...Ch. 5 - P5.16 Convection heat transfer data are often...Ch. 5 - If you disturb a tank of length L and water depth...Ch. 5 - Prob. 5.18PCh. 5 - Prob. 5.19PCh. 5 - Prob. 5.20PCh. 5 - Prob. 5.21PCh. 5 - As will be discussed in Chap. 11, the power P...Ch. 5 - The period T of vibration of a beam is a function...Ch. 5 - Prob. 5.24PCh. 5 - The thrust F of a propeller is generally thought...Ch. 5 - A pendulum has an oscillation period T which is...Ch. 5 - Prob. 5.27PCh. 5 - Prob. 5.28PCh. 5 - P5.29 When fluid in a pipe is accelerated linearly...Ch. 5 - Prob. 5.30PCh. 5 - P5.31 The pressure drop per unit length in...Ch. 5 - A weir is an obstruction in a channel flow that...Ch. 5 - Prob. 5.33PCh. 5 - Prob. 5.34PCh. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - Prob. 5.40PCh. 5 - A certain axial flow turbine has an output torque...Ch. 5 - When disturbed, a floating buoy will bob up and...Ch. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - P5.45 A model differential equation, for chemical...Ch. 5 - P5.46 If a vertical wall at temperature Tw is...Ch. 5 - The differential equation for small-amplitude...Ch. 5 - Prob. 5.48PCh. 5 - P5.48 A smooth steel (SG = 7.86) sphere is...Ch. 5 - Prob. 5.50PCh. 5 - Prob. 5.51PCh. 5 - Prob. 5.52PCh. 5 - Prob. 5.53PCh. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - P5.56 Flow past a long cylinder of square...Ch. 5 - Prob. 5.57PCh. 5 - Prob. 5.58PCh. 5 - Prob. 5.59PCh. 5 - Prob. 5.60PCh. 5 - Prob. 5.61PCh. 5 - Prob. 5.62PCh. 5 - The Keystone Pipeline in the Chapter 6 opener...Ch. 5 - Prob. 5.64PCh. 5 - Prob. 5.65PCh. 5 - Prob. 5.66PCh. 5 - Prob. 5.67PCh. 5 - For the rotating-cylinder function of Prob. P5.20,...Ch. 5 - Prob. 5.69PCh. 5 - Prob. 5.70PCh. 5 - The pressure drop in a venturi meter (Fig. P3.128)...Ch. 5 - Prob. 5.72PCh. 5 - Prob. 5.73PCh. 5 - Prob. 5.74PCh. 5 - Prob. 5.75PCh. 5 - Prob. 5.76PCh. 5 - Prob. 5.77PCh. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - A one-fiftieth-scale model of a military airplane...Ch. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - *P5.85 As shown in Example 5.3, pump performance...Ch. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - P5.89 Wall friction Tw, for turbulent flow at...Ch. 5 - Prob. 5.90PCh. 5 - Prob. 5.91PCh. 5 - Prob. 5.1WPCh. 5 - Prob. 5.2WPCh. 5 - Prob. 5.3WPCh. 5 - Prob. 5.4WPCh. 5 - Prob. 5.5WPCh. 5 - Prob. 5.6WPCh. 5 - Prob. 5.7WPCh. 5 - Prob. 5.8WPCh. 5 - Prob. 5.9WPCh. 5 - Prob. 5.10WPCh. 5 - Given the parameters U,L,g,, that affect a certain...Ch. 5 - Prob. 5.2FEEPCh. 5 - Prob. 5.3FEEPCh. 5 - Prob. 5.4FEEPCh. 5 - Prob. 5.5FEEPCh. 5 - Prob. 5.6FEEPCh. 5 - Prob. 5.7FEEPCh. 5 - Prob. 5.8FEEPCh. 5 - In supersonic wind tunnel testing, if different...Ch. 5 - Prob. 5.10FEEPCh. 5 - Prob. 5.11FEEPCh. 5 - Prob. 5.12FEEPCh. 5 - Prob. 5.1CPCh. 5 - Prob. 5.2CPCh. 5 - Prob. 5.3CPCh. 5 - Prob. 5.4CPCh. 5 - Does an automobile radio antenna vibrate in...Ch. 5 - Prob. 5.1DPCh. 5 - Prob. 5.2DP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 1:20 scale down model of a hydrofoil is tested in a water channel, at velocity of 0.179 m/s. At this velocity, a drag force of 2.2 N is measured. Determine the drag force of the original hydrofoil, at velocity of 0.8 m/s.arrow_forwardThe drag polar equation of a light airplane in clean configuration can be written as Cp = 0.358 + 0.0405 C₁². It has a weight of 18,681 N. The wing area is 14.41 m². Calculate the minimum power required in watts. (Round off answer with no decimal places, No units, No commas) Answer given: 1461792 A 5,000 lbs. aircraft has an excess power of 75 hp at sea level. If the service ceiling is 3,657.6 m, determine the time to climb from sea level to absolute ceiling in minutes. (Round off answer with no decimal places. No units, No commas) Answer given: 17arrow_forwardA 1:20 scaled-down model of a hydrofoil is tested in a water channel, at a velocity of 0.179 m/s. At this velocity, a drag force of 2.2 N is measured. Determine the drag force of the original hydrofoil, at a velocity of 0.8 m/s.arrow_forward
- A 5,000 lb airplane with wing area of 250 sq. ft and power available of 450 hp is at sea level flight standard condition. The airplane drag-to-lift relation is close to Co = 0.025 + 0.048 CL². What is the rate of climb (in feet per minute) at a flight speed of 180 miles per hour?arrow_forwardHow do we use the Buckingham pi theorem to prove that drag coefficient is dimensionless?arrow_forwardA 30-cm-diameter smooth ball of density Phall = 210 kg/m³ is tied to an object on the bottom of a river as shown on the right. Determine the angle 0 when the speed of the river current is a. U = 1.66 m/s b. U = 0.13 m/s c. For which velocity, the drag coefficient is lower? Explain why? 30° Take the density and viscosity of water in the river Pwater = 1000 kg/m², µwater = 0.001 kg/m's. Neglect the weight of the cable and the drag on it. 400 200 100 80 60 40 20 10 0.8 0.6 0.4 0.2 0.08 0.06 2 4 68 10- 2 4 68 2 4 68 2 4 68 102 2 4 68 103 pvd 2 4 68 10 2 4 68 10 100 10 105 Reynolds number, Drag coefficient, Cparrow_forward
- A ship is 125 m long and has a wetted area of 3500 m2.Its propellers can deliver a maximum power of 1.1 MWto seawater at 20°C. If all drag is due to friction, estimatethe maximum ship speed, in kn.arrow_forwardSome engineers want a good estimate of drag and boundary-layerthickness at the trailing edge of a miniature wing. The chord and span ofthe wing are 6 mm and 30 mm, respectively and a typical flight speed is5 m/s in air (kinematic viscosity = 15 × 10−6 m2/s; density = 1.2kg/m3). An engineer may decide to make a superseding model withchord and span of 150 mm and 750 mm, respectively. Measurements onthe model in a water channel flowing at 0.5 m/s (kinematic viscosity = 1× 10−6 m2/s, density = 1000 kg/m3) give a drag of 0.19 N and aboundary-layer thickness of 3 mm. Estimate the corresponding values forthe prototypearrow_forwardThe net drag of a moving body is produced by both pressure and shear stress effects. In most instance these two effects are considered together and an overall drag coefficient CD, defined as CD = D/(1/2 rU2A)。The drag coefficient are depend on what physical effects or dimensionless number.arrow_forward
- The drag coefficient for a car with a frontal area of 26 ft? is being measured in an 8 ft x 8 ft wind tunnel. The density of air under the test conditions is 2.4 x 10 3 slugs/ft, When the air flow rate is, 500,000 ft/min, the drag force on the car was measured to be 170 lb. The drag coefficient under the test conditions is most nearly O 0.30 O 0.32 O 0.28 O 0.34arrow_forwardConsider again a semi truck traveling at 55 mph on the freeway. The ambient air is at 1 atm and 80F. The trailer of the truck can be considered as a 8-ft-wide, 10-ft-high, 48-ft-long rectangular box. Assuming flat plate boundary layer behavior and no flow separation, estimate the drag force acting on the top and side surfaces and the power [hp] required to overcome this drag. Does the analysis seem reasonable for the actual drag force for the truck? Explain.arrow_forwardAn airplane has a mass of 50,000 kg (without load), a wing area of 360 m2 , a maximum lift coefficient of 3.25, and a cruising drag coefficient of 0.03 at an altitude of 12,000 m. Taking the density of standard air as ρ1 = 1.225 kg/m3 at sea level and ρ2 = 0.312 kg/m3 at 12,000 m altitude. (a) Generate a plot on computer software ( excel, matlab, etc.) of the safe takeoff speed at sea level Vs the load carried by the airplane (ranging from 0 kg to 20,000 kg of load). (b) Determine the power that must be delivered by the engines for a cruising speed of 800 km/hr.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License