Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 14MC
Technician A says that jack stands should always be used with portable floor jacks. Technician B says lifting capacity and operation should be checked before using a floor jack. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
What is the best way to lift a vehicle when preparingto remove an engine?a. Frame contact hoistb. Drive on liftc. Hydraulic jack and safety standsd. Engine hoist
Differentiate between a fast and loose pulley.
Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches?
a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds
While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation.
a. True b. False
Rusted-through brake lines are uncommon.
a. True b. False
A technician is diagnosing a vehicle with…
Chapter 5 Solutions
Automotive Technology
Ch. 5 - Explain how to properly use and care for a...Ch. 5 - List some common uses ot the dial indicator.Ch. 5 - Wrenches are available in several styles. List and...Ch. 5 - How do manufacturers inform technicians about...Ch. 5 - Prob. 5SACh. 5 - Describe three sources of service information...Ch. 5 - Prob. 1MCCh. 5 - Which of the following wrenches is the best choice...Ch. 5 - Technician A says that a micrometer can be used to...Ch. 5 - Prob. 4MC
Ch. 5 - Which of the following screwdrivers is like a...Ch. 5 - Technician A says most US bolts have a thread...Ch. 5 - Technician A uses a punch to align holes in parts...Ch. 5 - An extractor is used for removing broken. seals...Ch. 5 - Prob. 9MCCh. 5 - Technician A uses a blowgun to blow off parts...Ch. 5 - Technician A says that flare nut or line wrenches...Ch. 5 - Technician A uses a dial indicator to take inside...Ch. 5 - For a measurement that must be made within one...Ch. 5 - Technician A says that jack stands should always...Ch. 5 - When using an air impact wrench. Technician A uses...Ch. 5 - While discussing thread sealants and lubricants:...Ch. 5 - The metric equivalent to 10 miles is. 0.06895 bar...Ch. 5 - Which of the following thread designs typically...Ch. 5 - Which of the following is not measured with a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. Falsearrow_forwardWhen reviewing the procedure for replacing an axle boot, Technician A says that the position of the old boot should be marked on the shaft before removing it. Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardWhile discussing the different types of pressureplates: Technician A says that coil spring types arecommonly used because they have strong springs.Technician B says that Belleville-type pressure platesare not commonly used because they require excessivespace in the bell housing. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forward
- Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is released. Technician B says that a return spring is used to retract a caliper piston. Who is correct?arrow_forward14.A. What type of seal system is constructed of a hard brittle material and is often used in a pump to sealbetween the pump and the motor?A. SteelB. CeramicC. Glass 14.B. When a pneumatic solenoid fails, the failure is normally due to aA. weak pilot.B. bad spool.C. ripped seal. 14.C. When you're dealing with a PM task for a drive-belt form of conveyor, and you must make trackingadjustments to the belt, you shouldA. pull the belt back with pliers or a belt puller and see if it returns to the previous tracking marks. B. perform tracking adjustments at both ends of the belt.C. make a small adjustment, then continue with small adjustments as needed.arrow_forwardTechnician A says that load-carrying ball jointsshould always have some play in them. Technician Bsays that follower ball joints should never have someplay in them. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forward
- B.1. A chain-drive system can be aligned easier than a belt-drive system since the chain-drive systemA. can have a string left on the sprockets after the alignment is complete.B. can have the chain removed while the final alignment is taking place.C. has better areas to locate a straightedge.D. is less critical to misalignment.B.2. If there's no adjusting valve at the outlet of a large pump, there should be a(n)A. aerator in the pump.B. orifice plate at the inlet.C. orifice plate in the outlet.D. flow valve at the inlet.B.3. The best way to gauge the quality of the oil in a gearbox is by performing oilA. filtration.B. analysis.C. separation.D. titration.arrow_forwardInjuries in a workshop are often caused by incorrect lifting or moving of heavy loads. Name and briefly explained two (2) precautions that should be taken when removing a gearbox from a vehicle on a hoist.arrow_forwardFor the pulley system below, which equation is true about the length of the cord marked as green? If L1 is the length of the cord, while C1 is a constant. Hint: there are 2 cords, thus 2 equations on cord lengths. A. B. C. None of the above. D.arrow_forward
- A vehicle to be liftedarrow_forwardTechnician A says a sticking inboard joint can cause the car to shimmy during acceleration. Technician B says a worn inboard joint can cause a clunking during acceleration and deceleration. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardTechnician A uses a micrometer to measure the connectingrod journal for taper. Technician B uses amicrometer to measure the connecting rod journalfor out-of-roundness. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License