While discussing the different types of pressureplates: Technician A says that coil spring types arecommonly used because they have strong springs.Technician B says that Belleville-type pressure platesare not commonly used because they require excessivespace in the bell housing. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B

While discussing the different types of pressureplates: Technician A says that coil spring types arecommonly used because they have strong springs.Technician B says that Belleville-type pressure platesare not commonly used because they require excessivespace in the bell housing. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter37: Clutches

Section: Chapter Questions

Problem 3ASRQ: While discussing the different types of pressure plates: Technician A says that coil spring types...

See similar textbooks

Similar questions

While discussing the different types of pressure plates: Technician A says that coil spring types are commonly used because they have strong springs. Technician B says that Belleville-type pressure plates are not commonly used because they require excessive space in the bell housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
While discussing types of coil springs: Technician A says that linear-rate coil springs have equal spacing between the coils. Technician B says that a variable-rate/progressive springs may have a cylindrical shape with unequally spaced coils. Who is correct?
Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is released. Technician B says that a return spring is used to retract a caliper piston. Who is correct?
A discussion concerning CV joint testing is being held. Technician A says that a recommended method to check CV joints is to raise the vehícle so that the lower control arms are hanging freely; at this point the engine can be accelerated while noise checks can be performed. Technician B says that the vehicle should be road tested so that the CV joints can be checked under load. Who is correct? O a. A only O b. B only c. Both A and B d. Neither A nor B
When installing a new release bearing, Technician A says the outer surface of thetransmission's front bearing retainer should be lubricated. Technician B says the release lever and pivot shuold be lubricated who is correct? a. techincian A b. Technician B c. both A and B d. Neither A or B
When does expansion of spring and retraction of cylinder take place in spring type single acting cylinde Select one: a. oil pressure exerted and spring compression pressure are not same. b. oil pressure exerted and spring compression pressure are same. c. oil pressure exerted is more than spring compression pressure. O d. oil pressure exerted is less than spring compression pressure.
A car jumps out of gear into neutral, particularlywhen decelerating or going down hills: Technician Achecks the shift lever and external gearshift linkagefirst. Technician B says that the clutch pilot bearingcould be the problem. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B
Describe uncontrolled spring action without a shock absorber.
30. Which of the following is NOT a spring type used in pressure plate assemblies?A. Belleville B. CoilC. Diaphragm D. Torsional
The output shaft of a reducer is bearing in bearings A and B. From deep groove ball bearings, bed A is fixed and bed B is free-formed. Which of the following is true for the inner and Outer Ring of the bearing in bearing B?Please select one: a. Because the FG force acts on the shaft, there are no forces coming to the bracelets.b. the inner ring has a point, and the Outer Ring has an environmental load.c. Environmental load affects the outer ring.d. environmental load acts on the inner ring and point load acts on the outer ring.e. both environmental and point load affect the inner ring.
What is the name of this part? a. coil spring b. butterfly valve c. none of the choices d. governor Show proof. Please answer honestly and do not just guess. Thank you.
14.A. What type of seal system is constructed of a hard brittle material and is often used in a pump to sealbetween the pump and the motor?A. SteelB. CeramicC. Glass 14.B. When a pneumatic solenoid fails, the failure is normally due to aA. weak pilot.B. bad spool.C. ripped seal. 14.C. When you're dealing with a PM task for a drive-belt form of conveyor, and you must make trackingadjustments to the belt, you shouldA. pull the belt back with pliers or a belt puller and see if it returns to the previous tracking marks. B. perform tracking adjustments at both ends of the belt.C. make a small adjustment, then continue with small adjustments as needed.