Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 46, Problem 7ASRQ
When the front wheels are turned on a vehicle equipped with front struts, the left front coil spring provides a chattering action and noise: Technician A says that the strut has internal defects and strut replacement is necessary Technician B says that the upper strut bearing and mount are defective. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
When reviewing the service procedures for CV joints and drive axles,
Technician A says that the axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle.
Technician B says that a drive axle should never be allowed to hang by its own weight during removal or installation.
Who is correct?
O a. A only
Ob.B only
O c. Both A and B
O d. Neither A nor B
TRUE OR FALSE1. The primary and secondary suspensions are designed to achieve very poor ride quality, not safe performance during curve negotiation and bad dynamic behavior on a tangent track.
2. Each bogie frame is connected to car body through side bearings.
3. the wheel sets are located within a frame, either a bogie or directly in the vehicle, and are restrained by a large yaw stiffness.
4. When considering maintenance for railways, often the consequences can easily be changed.
5. Maintenance can only have positive effects.
6. Corrective maintenance also called as down systems.
7. the disadvantage of this system is the relatively low frequency of maintenance.
Technician A says that leaf spring type suspensions are subject to wheel tramp. Technician B says that anti sway bars are designed to limit wheel tramp. Who is correct?
Chapter 46 Solutions
Automotive Technology
Ch. 46 - Prob. 1SACh. 46 - Explain the difference between sprung and unsprung...Ch. 46 - What are two reasons for using an air spring?Ch. 46 - Explain the action of the conventional shock...Ch. 46 - Prob. 5SACh. 46 - Describe the common complaints caused by faulty...Ch. 46 - Prob. 7SACh. 46 - What occurs when a wheel hits a dip or hole and...Ch. 46 - Which of the following is part of the sprung...Ch. 46 - What occurs when a wheel hits a dip or hole and...
Ch. 46 - The modified MacPherson rear strut suspension is...Ch. 46 - What is used to control the movement of a vehicle...Ch. 46 - The coil springs of the vehicle_. a. support the...Ch. 46 - SLA systems in common use today are used in the...Ch. 46 - A multilink front suspension contains which of the...Ch. 46 - Technician A says that the use of firmer, urethane...Ch. 46 - Prob. 2ASRQCh. 46 - Technician A says that a weak suspension spring...Ch. 46 - Technician A says that leaf spring-type rear...Ch. 46 - Technician A says that shock absorbers should be...Ch. 46 - While discussing types of coil springs: Technician...Ch. 46 - When the front wheels are turned on a vehicle...Ch. 46 - Technician A says that the suspension switch must...Ch. 46 - While conducting a bounce test: Technician A says...Ch. 46 - Technician A says that rattling on road...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A multilink front suspension contains which of the following? a. Strut b. Control arms c. Ball joints d. All of the abovearrow_forwardExplain the difference between sprung and unsprung weight.arrow_forwardWhile conducting a bounce test: Technician A says that the bumper should be pushed two or three times downward with considerable weight applied on each corner of the vehicle. The bumper should be released after each push and the vehicle should oscillate about 1½ cycles and then settle. Technician B says that one free upward bounce should stop the vertical chassis movement if the shock absorber or strut provides proper spring control. If the vehicle’s bumper does more than 1½ free upward bounces, the shock absorber or strut is defective. Who is correct?arrow_forward
- When reviewing the procedure for replacing an axle boot, Technician A says that the position of the old boot should be marked on the shaft before removing it. Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardThe worm wheel rim is made of copper forA.Easy to manufacture B.Stable transmissionC.High precision D.Wear reductionarrow_forwardWhen the clutch is disengauged, where does the power flow stop? Select one: a. the transmission input shaft b. the driven hub c. the pressure plate and flywheel d. the torsion springsarrow_forward
- When discussing CV joint diagnosis, Technician A says that the complete failure of a CV joint may cause the vehicle not to hold in Park. Technician B says that a worn axle dampener assembly can cause a vibration while driving. Who is correct? O a. A only O b. B only c. Both A and B O d. Neither A nor Barrow_forwardFrom the following identify a true statement regarding the adjustment of drive belt tension. а. More than 6 mm should be the correct a deflection for each belt which is under tension O b. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension. c. More than 8 mm should be the correct a deflection for each belt which is under tension. O d. Less than 8 mm should be the correct a deflection for each belt which is under tensionarrow_forwardTech A says that caster can be adjusted on nearly all front suspensions. Tech B says that toe can only be adjusted on front suspension. Who is correctarrow_forward
- The modified MacPherson rear strut suspension is common in _______. a. FWD vehicles b. RWD vehicles c. pickup trucks d. station wagonsarrow_forwardFrom the following identify a true statement regarding the adjustment of drive belt tension. a. Less than 8 mm should be the correct a deflection for each belt which is under tension b. More than 6 mm should be the correct a deflection for each belt which is under tension c. More than 8 mm should be the correct a deflection for each belt which is under tension. d. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension.arrow_forwardWhat type of ball joint is used on the lower control arm of an SLA suspension when the coil spring is placed between the lower control arm and the frame, and the control arm is beneath the knuckle?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License