Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 46, Problem 2ASRQ
To determine
The correct technician among the two, i.e., A and B who are discussing the play in the load-carrying ball joint and follower ball joint respectively.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
When reviewing the procedure for replacing an axle boot,
Technician A says that the position of the old boot should be marked on the shaft before removing it.
Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
Technician A says a sticking inboard joint can cause the car to shimmy during acceleration.
Technician B says a worn inboard joint can cause a clunking during acceleration and deceleration.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
A vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced.
Technician A says that the left inner CV joint may be the source of the noise.
Technician B says that the left outer CV joint may be causing the noise.
Who is correct?
O a. A only
Ob.B only
O c. Both A and B
O d. Neither A nor B
Chapter 46 Solutions
Automotive Technology
Ch. 46 - Prob. 1SACh. 46 - Explain the difference between sprung and unsprung...Ch. 46 - What are two reasons for using an air spring?Ch. 46 - Explain the action of the conventional shock...Ch. 46 - Prob. 5SACh. 46 - Describe the common complaints caused by faulty...Ch. 46 - Prob. 7SACh. 46 - What occurs when a wheel hits a dip or hole and...Ch. 46 - Which of the following is part of the sprung...Ch. 46 - What occurs when a wheel hits a dip or hole and...
Ch. 46 - The modified MacPherson rear strut suspension is...Ch. 46 - What is used to control the movement of a vehicle...Ch. 46 - The coil springs of the vehicle_. a. support the...Ch. 46 - SLA systems in common use today are used in the...Ch. 46 - A multilink front suspension contains which of the...Ch. 46 - Technician A says that the use of firmer, urethane...Ch. 46 - Prob. 2ASRQCh. 46 - Technician A says that a weak suspension spring...Ch. 46 - Technician A says that leaf spring-type rear...Ch. 46 - Technician A says that shock absorbers should be...Ch. 46 - While discussing types of coil springs: Technician...Ch. 46 - When the front wheels are turned on a vehicle...Ch. 46 - Technician A says that the suspension switch must...Ch. 46 - While conducting a bounce test: Technician A says...Ch. 46 - Technician A says that rattling on road...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When installing a new release bearing, Technician A says the outer surface of thetransmission's front bearing retainer should be lubricated. Technician B says the release lever and pivot shuold be lubricated who is correct? a. techincian A b. Technician B c. both A and B d. Neither A or Barrow_forwardTechnician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. Falsearrow_forwardTechnician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. False Rusted-through brake lines are uncommon. a. True b. False A technician is diagnosing a vehicle with…arrow_forward
- When discussing shift problems, Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. Technician B that poor shift boot alignment can cause a transaxle to jump out of gear. says Who is correct? A. A only C. Both A and B B. B only D. Neither A nor Barrow_forwardonly use revolute jointsarrow_forwardTechnician A says that the piston seal retracts the caliper piston when hydraulic pressure is released. Technician B says that a return spring is used to retract a caliper piston. Who is correct?arrow_forward
- Technician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt may become fatigued if it is under tightened. Who is correct?arrow_forwardThe CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart. Technician A says that one or more of the engine/transaxle's mounts may be broken. Technician B says that one or more of the engine/transaxle's subframe mounts may be broken. Who is correct? O a. A only O b.B only C. Both A and B O d. Neither A nor Barrow_forward2. Technician A says that the purpose of the steering wheel holder is to make sure that the steeringwheel is centered after the alignment. Technician B says that if the steering wheel is not centered after an alignment, it should be pulled offthe column and positioned correctly. Who iscorrect?a. Technician A c. Both A and B b. Technician B d. Neither A nor Barrow_forward
- A link which transmits the motion with negligible deformation is called as a. rigid link. b. flexible link. c. fluid link. d. resistant body.arrow_forwardWhen reviewing the service procedures for CV joints and drive axles, Technician A says that the axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle. Technician B says that a drive axle should never be allowed to hang by its own weight during removal or installation. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forwardDraw FBD of Bicycle axle (Thru axle)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning