Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 45, Problem 8ASRQ
To determine
The correct technician among the two, i.e., A and B who are discussing run-flat tires.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician a says radial ply tires are more rigid in the sidewall area than bias ply tires. Technician b says the belts in a radial tire restrict tread motion during contact with the road thus improving tread life in traction. who is correct
i need the answer quickly
Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight . Technician B says that low unsprung weight makes the vehicle handle better on irreg ular surfaces. Who is correct?
Chapter 45 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 45 - List five things that could cause premature...Ch. 45 - Define lateral and radial runout.Ch. 45 - Prob. 3RQCh. 45 - Define dynamic and static wheel balance.Ch. 45 - Describe the proper procedure to seal a puncture...Ch. 45 - The rim offset is the vertical distance between...Ch. 45 - Prob. 7RQCh. 45 - True or False? All TPMS have a pressure sensor...Ch. 45 - A tire that wobbles from side-to-side is said to...Ch. 45 - A front tire has excessive wear on both edges of...
Ch. 45 - All of the following statements are correct...Ch. 45 - All of the following statements are correct...Ch. 45 - Which of the following statements about sidewall...Ch. 45 - All of these statements about improper wheel...Ch. 45 - Prob. 15RQCh. 45 - Technician A says that the front wheel bearings on...Ch. 45 - Technician A says that dynamic wheel imbalance...Ch. 45 - Technician A says that front bearing assembly...Ch. 45 - Technician A says that replacement wheel rims...Ch. 45 - Prob. 5ASRQCh. 45 - While choosing the correct tire for a vehicle:...Ch. 45 - Technician A says that on most vehicles, the...Ch. 45 - Prob. 8ASRQCh. 45 - Prob. 9ASRQCh. 45 - Prob. 10ASRQ
Knowledge Booster
Similar questions
- During the useful life of a set of new tires (including the spare), it is necessary to rotate them at intervals of about-------- for rear drive vehicles and- for front drive vehicles to get the most mileage out of them. 3000 km,2000 mile 3330 km,2225 mile 3000 mile,2500 mile 3000mile,2000 mile Skip In diesel engines, re-calibrate injectors and pumps (This should be done by the authorized agencies and preferably in air- conditioned rooms). * fitness certificate work Daily Maintenance Monthly Maintenance Quarterly Maintenancearrow_forwardWhat is the principle of the balancing act in tires?arrow_forwardWhile discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- Technician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicles wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct? a. Technician A only b. Technician B only c. Both A and B Neither A nor Barrow_forwardAn indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forwardTechnician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forward
- Replacing the tyre after it burst is example of breakdown maintenance. an Select one: O True O Falsearrow_forwardWhen replacing brake pads on a vehicle: Tech-nician A works on one wheel before beginning work on another. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardA tire that wobbles from side-to-side is said to have -----· a.radial runout b.lateral runout c.static imbalance d.none of the abovearrow_forward
- While diagnosing the problems that can be caused by worn tie-rod ends: Technician A says that they can cause scalloped and scuffed tires. Technician B says that they can cause the vehicle to pull to one side. Who is correct?arrow_forwardAll of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tirearrow_forwardTechnician A says a sticking inboard joint can cause the car to shimmy during acceleration. Technician B says a worn inboard joint can cause a clunking during acceleration and deceleration. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,