Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 45, Problem 5RQ
Describe the proper procedure to seal a puncture in a tire.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following would NOT be cause for rejection when checking the tire condition?
Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame.
Any tire tread or recap is separated or any tire is flat.
All of the statements shown are cause for rejection.
Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.
what is the formula to measure gas from tire interior?
Which of the following statement is correct
Select one:
Friction causes objects to slip down
Friction causes objects to slow down
Friction causes objects to break down
Friction causes objects to move at small force
Chapter 45 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 45 - List five things that could cause premature...Ch. 45 - Define lateral and radial runout.Ch. 45 - Prob. 3RQCh. 45 - Define dynamic and static wheel balance.Ch. 45 - Describe the proper procedure to seal a puncture...Ch. 45 - The rim offset is the vertical distance between...Ch. 45 - Prob. 7RQCh. 45 - True or False? All TPMS have a pressure sensor...Ch. 45 - A tire that wobbles from side-to-side is said to...Ch. 45 - A front tire has excessive wear on both edges of...
Ch. 45 - All of the following statements are correct...Ch. 45 - All of the following statements are correct...Ch. 45 - Which of the following statements about sidewall...Ch. 45 - All of these statements about improper wheel...Ch. 45 - Prob. 15RQCh. 45 - Technician A says that the front wheel bearings on...Ch. 45 - Technician A says that dynamic wheel imbalance...Ch. 45 - Technician A says that front bearing assembly...Ch. 45 - Technician A says that replacement wheel rims...Ch. 45 - Prob. 5ASRQCh. 45 - While choosing the correct tire for a vehicle:...Ch. 45 - Technician A says that on most vehicles, the...Ch. 45 - Prob. 8ASRQCh. 45 - Prob. 9ASRQCh. 45 - Prob. 10ASRQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How does a technician determine the proper inflation for a vehicle's tires?arrow_forwardWhich of the following statements about sidewall markings is correct? a. The load index is given as a letter. b. The traction and temperature ratings are based on the speed rating of the tire. c. The tires recommended inflation pressure and load are indicated. d. The DOT code indicates when and where the tire was made.arrow_forwardAll of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tirearrow_forward
- An indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forwardAll of the following statements are correct except? a. Tire inflation pressure directly affects traction. b. The recommended tire pressure for front and rear tires may be different. c. The recommended tire pressures are often lower than maximum pressures. d. The recommended tire pressure is molded into the sidewall of the tire.arrow_forwardAll of the following statements are correct except? a. Belts are reinforcing materials that encircle the tire under the tread. b. The carcass of a tire is made up of plies, layers of cloth, and rubber. c. Most tread patterns are designed to work well on both wet and dry roads. d. The bead is the decorative pattern at the outer edge of the tread.arrow_forward
- While discussing the common causes for cracks developing in a cylinder block or head: Technician A says that the chilling of a hot engine by a sudden rush of cold water or air over the surf ace may cause cracking. Technician B says that excessive overheating is a common cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following would NOT be cause for rejection when checking the windshield and other glass? Any window is broken or has sharp or jagged edges. Any window other than the windshield is cracked, starred, scratched, or discolored so as to obstruct the driver’s view. The vehicle is not equipped with approved safety glass or is not equipped with a windshield. The windshield has a 2 inch diameter“star”.arrow_forwardA P195/75R14 tire classification includes both metric and English standard measurements. True Falsearrow_forward
- what is ASTM D566 Dropping point tester for Lubricating Grease? own words ALL THE BESTarrow_forwardReplacing the tyre after it burst is example of breakdown maintenance. an Select one: O True O Falsearrow_forwardWhile discussing the causes of extreme engine bearing damage Technician A says that contaminated and old engine oil could be the cause. Technician B says that a leaking radiator could be the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License