Concept explainers
A dual-fluid heat exchanger has
Want to see the full answer?
Check out a sample textbook solutionChapter 4 Solutions
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
Additional Engineering Textbook Solutions
Manufacturing Engineering & Technology
Engineering Mechanics: Statics
Statics and Mechanics of Materials (5th Edition)
Applied Fluid Mechanics (7th Edition)
Mechanics of Materials
Fox and McDonald's Introduction to Fluid Mechanics
- A heat exchanger uses medium pressure steam at 10 bar and 350 C to heat cyclohexane vapor from 100 C up to 275 C as shown in the figure below. The steam is available at a flowrate of 32 kg/h and it condenses completely in the heat exchanger and exits as saturated liquid condensate at 10 bar. a) How much heat (in kW) can be provided by the steam? b) How much cyclohexane can be processed in kg/h? Vapor Cyclohexane T = 100 C P = 1 atm Steam T = 350 C = 10 bar Condensate P Vapor Cyclohexane T = 275 C P = 1 atm P = 10 bararrow_forwardan air flow is brought from 20 degree celsius, 100 kPa to 1000 kPa, 330 degree celsius by an adiabatic compressor driven by 50 kW motor. what are the mass flow rate and the exit volume flow rate of air?arrow_forwardNitrogen at a flow rate of 0.1 kg / s enters a heat exchanger at a temperature of 450 K and 320 It comes out at K temperature. The other fluid of the heat exchanger is water, it enters at 20 ° C and leaves at 35 ° C. a) Calculate the flow of water. b) Calculate the entropy generation in this heat exchanger. (Take the average specific heating heat for nitrogen as 1.042 kJ / kgK.)arrow_forward
- The radiator of an air-water cooled Diesel engine has a surface area of 10 m. Water at 90°C enters at 1 kg/s rate and leaves at 60 °C. Air at 30 C is forced through the radiator by an air fan and leaves the radiator at 45 C. Find: 5. a. Amount of heat transferred b. The value of overall heat transfer coefficient, U с. Amount of air forced through the radiator Cwater 4.18 kJ/kg.K, Cair= 1.007 kJ/kg.Karrow_forward(b) Velocity ratio of a machine is 72. The law of machine is P=1/48 W+30 N. Find the maximum MA, efficiency and state whether machine is reversible.arrow_forwardA heat exchanger as shown in the below figure is used for an air conditioning system through a chilled water. Hot air at bar and 37 °C enters the heat exchanger at a volume flowrate of 1 m3/s leaving at 20 °C. The chilled water enters the heat exchanger at 5 °C and 1.5 bar and leaves as warm water at 12 °C and same pressure. The heat transfer from the outer surface of the heat exchanger is neglected. Similarly, the kinetic and potential energy difference in both the air a water at the inlet and exit is negligible. Assume constant specific heats for water and for air. At steady state operation, determine: (a) The mass flowrate of the water, and (b) The rate of heat transfer between the water and the air in kW. Hot Air P3=1 bar T3 V3 Chilled Water P,=1.5 bar T1 warm Water P,=1.5 bar T2 Conditioned Air P=1 bararrow_forward
- Ammonia exits the stream of a process as saturated liquid at a pressure of 11bar, and is reduced to 2.5bar in a throttle valve, said current is fed to a heat exchanger exiting at 30°C, When countercurrent contact with water at 0.9869atm and, 18°C the mass flow is 1kg/s and decreases 8°C. Determine: a)the refrigerant mass flow rate (kg/s) b) the coolant temperature at the valve outlet in °Carrow_forwardSteam to a turbine at a mass flow rate of 1.4 kg/s, 700 kPa pressure and 400 °C enters the temperature. Steam at 100 kPa pressure and 1.4 m3/kg specific volume exits the turbine. Heat transfer from turbine to environment 50 kW, with turbine Since the boundary temperature between the environment is 70 °C, a) Find the power produced by the turbine, entropy produced in the turbine and isentropic efficiency of the turbine. Note: The changes in kinetic and potential energies will be neglected and T (K) = 273 + °C will be taken.arrow_forwardHeat exchangers exchange only heat and not mass (fluid does not mix).The working fluid is water vapor that comes from a boiler and serves to heat cold water.Suppose that in this hypothetical application above, the water vapor enters at 500 kPa and 300 °C through the “pipe inlet” (see figure) and so is used to heat the cold water, which enters in the opposite direction through the “hull inlet” ” at 15 °C and goes to the “hull exit” exiting at 75 °C. How much steam per kg of liquid water is needed as long as the steam does not condense?arrow_forward
- The power of a steam turbine in a thermal power plant is 60 MW. Water vapor enters the turbine at 3MPa pressure, 4000C temperature and 50 m / s speed, 10 kPa pressure, 0.9 dry degree and 200 m / s speed leaves the turbine. Considering the turbine as adiabatic; 1-Find the mass flow of steam 2-Find the turbine outlet cross-sectional area, its ratio (A2 / A1) to the inlet cross-sectional area.arrow_forwardSaturated water vapor at 85 ° C comes out of a turbine and condenses on the outer surface of a cooling pipe 2 in diameter and 20 m long at a rate of 90 kg / hr. Find the rate of heat transfer from the steam to the cooling pipe.arrow_forwardA turbine operating in a continuous flow works adiabatically. The water vapor enters the turbine at a temperature of 650 C and comes out with 20 kPa pressure and 85% dryness. Find the mass flow rate (kg / sec) required to generate 10 MW of power from the system (ignore KE and PE changes)arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY