A heat exchanger uses medium pressure steam at 10 bar and 350 C to heatcyclohexane vapor from 100 C up to 275 C as shown in the figure below. Thesteam is available at a flowrate of 32 kg/h and it condenses completely in theheat exchanger and exits as saturated liquid condensate at 10 bar.a) How much heat (in kW) can be provided by the steam?b) How much cyclohexane can be processed in kg/h?VaporCyclohexaneT = 100 CP = 1 atmSteam T = 350 C= 10 barCondensatePVaporCyclohexaneT = 275 CP = 1 atmP = 10 bar A heat exchanger uses medium pressure steam at 10 bar and 350 C to heatcyclohexane vapor from 100 C up to 275 C as shown in the figure below. Thesteam is available at a flowrate of 32 kg/h and it condenses completely in theheat exchanger and exits as saturated liquid condensate at 10 bar.a) How much heat (in kW) can be provided by the steam?b) How much cyclohexane can be processed in kg/h?VaporCyclohexaneT = 100 CP = 1 atmSteam T = 350 C= 10 barCondensatePVaporCyclohexaneT = 275 CP = 1 atmP = 10 bar

Answered: Image /qna-images/answer/f39cf06a-889b-4f37-89b8-7ccba5030d33.jpg

A heat exchanger uses medium pressure steam at 10 bar and 350 C to heat cyclohexane vapor from 100 C up to 275 C as shown in the figure below. The steam is available at a flowrate of 32 kg/h and it condenses completely in the heat exchanger and exits as saturated liquid condensate at 10 bar. a) How much heat (in kW) can be provided by the steam? b) How much cyclohexane can be processed in kg/h?

A heat exchanger uses medium pressure steam at 10 bar and 350 C to heat cyclohexane vapor from 100 C up to 275 C as shown in the figure below. The steam is available at a flowrate of 32 kg/h and it condenses completely in the heat exchanger and exits as saturated liquid condensate at 10 bar. a) How much heat (in kW) can be provided by the steam? b) How much cyclohexane can be processed in kg/h?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. Air to H20 heat exchanger: Air enters a heat exchanger at (2000 F, 15 psia) and exits at (500 F, 15 psia). Saturated liquid H20 enters the heat exchanger at 300 F. The H20 is heated at a constant pressure and exits as a saturated vapor. The outer shell of the heat exchangers is insulated. The flow rate of the H20 is 100,000 Ibm/hr. Deterimine a. The volumetric flow rate of the air at the inlet (cfm) b. The rate of entropy generation within the heat exchanger (Btu/R/s)
) An open type heat exchanger (feed water heater) operates at 7 bar pressure. Compressed liquid water and superheated steam at 35°C enter heat exchanger and exits as saturated liquid. As the ratio of mass flow rates of compressed liquid and superheated steam flows is 4.5/1, determine a) The temperature of superheated steam b) Entropy generation during this process in kJ/kg.pthund stam K KARIŞIM ODASI 7 bar T35°C Pe7 bar su Kızgın buhar P-7 bar su P7 bar ve x0 su n, = m, + ih, -0.222 c)
In a surface condenser, O cooling water and steam passes over the tubes. steam and cooling water never mix to give condensate. steam and cooling water mix to give condensate O steam and cooling water passes inside the tubes .
2) Water vapor enters a continuous flow adiabatic turbine at 15 MPa pressure, 500 °C temperature and 90 m/s velocity, and exits at 20 kPa pressure, 92% dryness and 80 m/s speed. Since the mass flow rate of the steam is 43.2 tons/h, a) The power produced in the turbine (in MW, HP, ton.km/h), b) Find the turbine inlet and outlet cross-sectional areas (in m2, cm2).
Use the given values Air as an ideal gas flows through the turbine and heat exchanger arrangement. Steady-state data are given on the figure and on the table. Stray heat transfer and kinetic and potential energy effects can be ignored. a) Determine the power developed, ? ̇ in Turbine 2 Find the rates of entropy production, ?̇ each in kW/K, for b) Turbine 1 and c) Heat exchanger d) Which component contributes more to inefficient operation of the overall system? How do you know?
A heat exchanger has the objective of condensing 5 kg/s of water vapor and taking it from a pressure of 1.0 MPa and 300 °C to atmospheric pressure and 60 °C. Liquid water is used as refrigerant (Cp= 4.22 kJ/kgK), it enters at 1 °C and leaves the exchanger at 50 °C. a) What is the mass flow rate of the cold water stream? b) If the water is exchanged for another refrigerant substance whose specific heat is 2.0 kJ/kgK, what will be its outlet temperature if the same mass flow is maintained?
Heat Exchangers & Boilers are examples of heating units. true of fulse
Steam enters the steam-generating unit at a pressure of 20 bar and dryness of 0.96 and leaves at the same pressure at a temperature of 350°C. Mass flow rate of steam is 5 kg/s. Find the percentage increase in volume (%) due to drying and superheating.
A factory uses superheated steam (P = 15 bar, T = 250 oC) for heating purposes of 20,000 tons/month. Steam is made in a boiler-furnace using 2 (two) types of fuel, namely coal fuel (LHV = 5500 kcal/kg) and heavy fuel oil (137129 Btu/ft3, density = 0.98 m3/kg) Question: a. How much coal fuel is needed to produce steam with the above specifications if the overall efficiency of the system (boiler-furnace = 75%)! b. How much heavy fuel oil is needed to produce steam with the above specifications (boiler-furnace = 75%)! answer every month... Help pleasee.. fast please
P.2 (Application on Reversible process) Please answer is Why the Engineers are considered the reversible processes is very important to study?n0t written in (Application on Thermochemical Data for Q, U, H, Cv, and Cp) related words P.3 Calculate the internal-energy and enthalpy changes that occur when air is changed from an initial state of 277K and 10 bar, where is molar volume is 2.28 m³/Kmole, to a final state of 333K and 1 atm. Assume for air that PV/T is a constant and that C, = 21 and C, = 29.3 kJ/kgmole K.
3.24 You want to cool air from 150°C to 60°C but you cannot afford a custom-built heat exchanger. You find a used cross-flow exchanger (both fluids unmixed) in storage. It was previously used to cool 136 kg/min of NH3 vapor from 200°C to 100°C using 320 kg/min of water at 7°C; U was previously 480 W/m²K. How much air can you cool with this exchanger, using the same water supply, if U is approximately unchanged? (Actually, you would have to modify U using the methods of Chapters 6 and 7 once you had the new air flow rate, but that is beyond our present scope.)
A reheater cycle with two stages of reheating is executed with steam expanding initially from 20.356 Mpa and 540 oC. The pressures of two reheaters are 3.2356 Mpa and 0.85356 Mpa, and the steam leaves each reheater at 540oC. Condensation occurs at 70oC. Calculate W, ec and ee.