HEAT+MASS TRANSFER:FUND.+APPL.
6th Edition
ISBN: 9780073398198
Author: CENGEL
Publisher: RENT MCG
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 4, Problem 35P
Oxy-fuel combustion power plants use pulverized coal particles as fuel to burn in a pure oxygen environment to generate electricity. Before entering the furnace, pulverized spherical coal particles with an average diameter of 300 tm are transported at 2 m/s through a 3-m-long heated tube while suspended in hot air. The air temperature in the tube is 900°C, and the average convection heat transfer coefficient is 250 W/m2 K. Determine the temperature of the coal particles at the exit of the heated tube if the initial temperature of the particles is 20°C.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Combustion gases passing through a 3-cminternal- diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 115 kPa and 250°C at a mean velocity of 5 m/s, and leave at 150°C. If the average heat transfer coefficient is 120 W/m2?K and the inner surface temperature of the tube is 110°C, determine (a) the tube length and (b) the rate of evaporation of water.
Pulverized coal particles are used in oxy-fuel combustion power plants for electricity generation. Consider a situation where coal particles are suspended in hot air flowing through a heated tube, where the convection heat transfer coefficient is 100 W/m2·K. If the average surface area and volume of the coal particles are 3.1 mm2 and 0.5 mm3, respectively, determine how much time it would take to heat the coal particles to two-thirds of the initial temperature difference.
Inside a condenser, there is a bank of seven copper tubes with cooling water flowing in them. Steam
condenses at a rate of 0.5 kg/s on the outer surfaces of the tubes that are at a constant temperature of
70°C. Each copper tube is 6-m long and has an inner diameter of 20 mm. Cooling water (Cp=4120 J/kgK)
enters each tube at 5°C and exits at 60°C. Determine the average heat transfer coefficient of the cooling
water flowing inside each tube and the cooling water mean velocity needed to achieve the indicated heat
.transfer rate in the condenser
Steam
Cooling
water flow
Chapter 4 Solutions
HEAT+MASS TRANSFER:FUND.+APPL.
Ch. 4 - What is the physical significance of the Biot...Ch. 4 - What is lumped system analysis? When is it...Ch. 4 - In what medium is the lumped system analysis more...Ch. 4 - For which solid is the lumped system analysis more...Ch. 4 - For which kinds of bodies made of the same...Ch. 4 - Consider heat transfer between two identical hot...Ch. 4 - Consider heat transfer between two identical hot...Ch. 4 - Consider a hot baked potato on a plate. The...Ch. 4 - Consider a potato being baked in an oven that is...Ch. 4 - Consider two identical 4-kg pieces of roast beef....
Ch. 4 - Consider a sphere and a cylinder of equal volume...Ch. 4 - Obtain relations for the characteristic lengths of...Ch. 4 - Obtain a relation for the time required for a...Ch. 4 - A brick of 20310257mm in dimension is being burned...Ch. 4 - Prob. 15PCh. 4 - Prob. 16PCh. 4 - Prob. 17PCh. 4 - Metal plates...Ch. 4 - Prob. 19PCh. 4 - Prob. 20PCh. 4 - Prob. 21PCh. 4 - A 6-mm-thick stainless steel strip...Ch. 4 - After heat treatment, the 2-cm-thick metal plates...Ch. 4 - A long copper rod of diameter 2.0 cm is initially...Ch. 4 - Prob. 25PCh. 4 - Steel rods...Ch. 4 - Prob. 27PCh. 4 - Prob. 28PCh. 4 - To warm up some milk for a baby, a mother pours...Ch. 4 - A person is found dead at 5 p.m. in a room whose...Ch. 4 - Prob. 31PCh. 4 - In an experiment, the temperature of a hot gas...Ch. 4 - Prob. 33PCh. 4 - Pulverized coal particles are used in oxy-fuel...Ch. 4 - Oxy-fuel combustion power plants use pulverized...Ch. 4 - Plasma spraying is a process used for coating a...Ch. 4 - Consider a spherical shell satellite with outer...Ch. 4 - Prob. 38PCh. 4 - Prob. 39PCh. 4 - Prob. 40EPCh. 4 - Consider a sphere of diameter 5 cm, a cube of side...Ch. 4 - Prob. 42PCh. 4 - An egg is to be cooked to a certain level of...Ch. 4 - What is an infinitely long cylinder? When is it...Ch. 4 - What is the physical significance of the Fourier...Ch. 4 - Prob. 46CPCh. 4 - Prob. 47CPCh. 4 - The Biot number during a heat transfer process...Ch. 4 - A body at an initial temperature of Ti, is brought...Ch. 4 - Prob. 50PCh. 4 - In a meat processing plant, 2-cm-thick steaks...Ch. 4 - Prob. 52PCh. 4 - Prob. 53PCh. 4 - Prob. 54PCh. 4 - Prob. 55PCh. 4 - Layers of 23-cm-thick meat slabs...Ch. 4 - Prob. 57PCh. 4 - Prob. 58PCh. 4 - Prob. 59PCh. 4 - Prob. 60PCh. 4 - Prob. 61PCh. 4 - Prob. 62EPCh. 4 - Prob. 63PCh. 4 - Prob. 64PCh. 4 - Prob. 65PCh. 4 - Prob. 66PCh. 4 - A 30-cm-diameter, 4-m-high cylindrical column of a...Ch. 4 - Prob. 68PCh. 4 - Prob. 69PCh. 4 - Prob. 70PCh. 4 - For heat transfer purposes, an egg can be...Ch. 4 - Citrus fruits are very susceptible to cold...Ch. 4 - Chickens with an average mass of 1.7 kg...Ch. 4 - Prob. 74PCh. 4 - Prob. 75PCh. 4 - Prob. 76PCh. 4 - Oranges of 2.5-in-diameter...Ch. 4 - Prob. 78PCh. 4 - Prob. 79PCh. 4 - Prob. 80PCh. 4 - Prob. 81PCh. 4 - A 9-cm-diameter potato...Ch. 4 - In Betty Crocker s Cookbook, it is stated that it...Ch. 4 - Prob. 84PCh. 4 - Under what conditions can a plane wall be treated...Ch. 4 - What is a semi-infinite medium? Give examples of...Ch. 4 - Consider a hot semi-infinite solid at an initial...Ch. 4 - Prob. 88EPCh. 4 - Prob. 89PCh. 4 - In areas where the air temperature remains below...Ch. 4 - Prob. 91PCh. 4 - A highway made of asphalt is initially at a...Ch. 4 - A thick aluminum block initially at 20C is...Ch. 4 - Prob. 94PCh. 4 - A thick wall made of refractory bricks...Ch. 4 - Prob. 96PCh. 4 - Prob. 97PCh. 4 - A thick wood slab (k=0.17W/m.K,=1.2810-7m2/s) and...Ch. 4 - Prob. 99PCh. 4 - Prob. 100PCh. 4 - Prob. 101PCh. 4 - Prob. 102PCh. 4 - Prob. 103PCh. 4 - Prob. 104PCh. 4 - Prob. 105PCh. 4 - A barefooted person whose feet are at 32C steps on...Ch. 4 - What is the product solution method? How is it...Ch. 4 - How is the product solution used to determine the...Ch. 4 - Prob. 109CPCh. 4 - Consider a short cylinder whose top and bottom...Ch. 4 - Prob. 111PCh. 4 - Prob. 112PCh. 4 - Prob. 113PCh. 4 - A hot dog can be considered to be a cylinder 5 in...Ch. 4 - Prob. 115PCh. 4 - Prob. 116PCh. 4 - A 2-cm-high cylindrical ice block...Ch. 4 - Prob. 118PCh. 4 - Prob. 119PCh. 4 - Prob. 120PCh. 4 - Prob. 121PCh. 4 - Prob. 122PCh. 4 - Prob. 123PCh. 4 - Prob. 124CPCh. 4 - How does refrigeration prevent or delay the...Ch. 4 - What are the environmental factors that affect the...Ch. 4 - What is the effect of cooking on the...Ch. 4 - Prob. 128CPCh. 4 - Prob. 129CPCh. 4 - Prob. 130CPCh. 4 - Prob. 131CPCh. 4 - How does the rate of freezing affect the...Ch. 4 - Prob. 133CPCh. 4 - Prob. 134CPCh. 4 - Prob. 135CPCh. 4 - Prob. 136CPCh. 4 - Prob. 137CPCh. 4 - Prob. 138PCh. 4 - Chickens with an average mass of 2.2 kg and...Ch. 4 - Prob. 140EPCh. 4 - Prob. 141PCh. 4 - Prob. 142PCh. 4 - A long roll of 2-m-wide and 0.5-cm-thick 1-Mn...Ch. 4 - Prob. 144PCh. 4 - Prob. 145PCh. 4 - Prob. 146PCh. 4 - During a picnic on a hot summer day, the only...Ch. 4 - Two metal rods are being heated in an oven with...Ch. 4 - Stainless steel ball bearings...Ch. 4 - Prob. 150PCh. 4 - Prob. 151PCh. 4 - In Betty crockers Cookbook, it is stated that it...Ch. 4 - A watermelon initially at 35C is to be cooled by...Ch. 4 - Prob. 154PCh. 4 - Prob. 155PCh. 4 - Prob. 156PCh. 4 - Prob. 157PCh. 4 - Prob. 158PCh. 4 - Prob. 159PCh. 4 - Prob. 160PCh. 4 - Prob. 161PCh. 4 - Prob. 162PCh. 4 - Prob. 163PCh. 4 - Lumped system analysis of transient heat...Ch. 4 - Prob. 165PCh. 4 - Prob. 166PCh. 4 - An 18-cm-long, 16-cm-wide, and 12-cm-high hot iron...Ch. 4 - Prob. 168PCh. 4 - Prob. 169PCh. 4 - Prob. 170PCh. 4 - Prob. 171PCh. 4 - Prob. 172PCh. 4 - A long 18-cm-diameter bar made of hardwood...Ch. 4 - Consider a 7.6-cm-long and 3-cm-diameter...Ch. 4 - Consider a 7.6-cm-diameter cylindrical lamb meat...Ch. 4 - Prob. 176PCh. 4 - A small chicken (k=0.45W/m.K,=0.1510-6m2/s) and...Ch. 4 - A potato may be approximated as a 5.7-cm-diameter...Ch. 4 - When water, as in a pond or lake, is heated by...Ch. 4 - A large chunk of tissue at 35C with a thermal...Ch. 4 - Prob. 181PCh. 4 - Citrus trees are very susceptible to cold weather,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An average man has a body surface area of 1.8 m2 and a skin temperature of 330C. The convective heat transfer coefficient for a clothed person walking in still air is expressed as h= 8.6V0.53 where V is the walking velocity in m/s. Assuming the average surface temperature of the clothed person to be 300C, determine the rate of heat lost by convection from an average man walking in still air at 100C at a walking velocity of 1.2 m/s.arrow_forwardThe boiling temperature of oxygen at atmospheric pressure at sea level (1 atm) is -183ºC. Therefore, oxygen is used in low temperature scientific studies since the temperature of liquid oxygen in a tank open to the atmosphere remains constant at -183ºC until the liquid oxygen in the tank is depleted. Any heat transfer to the tank results in the evaporation of some liquid oxygen, which has a heat of vaporization of 213 kJ/kg and a density of 1140 kg/m3at 1 atm. Consider a 4 m diameter spherical tank initially filled with liquid oxygen at 1 atm and -183ºC. The tank is exosed to 20ºC ambient ait with a heat transfer coefficient of 25 W/m2. ºC. The temperature of the thin-shelled spherical tank is observed to be almost the same as the temperature of the oxygen inside. Disregarding any radiation heat exchange, determine the rate of evaporation of the liquid oxygen in the tank as a result of the heat transfer from the ambient airarrow_forwardIn a gas-fired boiler, water is being boiled at 120°C by hot air flowing through a 5-m-long, 5-cm-diameter tube submerged in water. Hot air enters the tube at 1 atm and 300°C at a mean velocity of 7 m/s and leaves at 150°C. If the surface temperature of the tube is 120°C, determine the average convection heat transfer coefficient of the air and the rate of water evaporation, in kg/h.arrow_forward
- Using EES (or other) software, investigate the effect of the exhaust gas inlet temperature on the rate of heat transfer, the exit temperature of exhaust gases, and the rate of evaporation of water. Let the temperature of exhaust gases vary from 300°C to 600°C. Plot the rate of heat transfer, the exit temperature of exhaust gases, and the rate of evaporation of water as a function of the temperature of the exhaust gases, and discuss the results.arrow_forwardCombustion gases passing through a 5-cm-internal-diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 225 kPa and 250°C at a mean velocity of 2.5 m/s, and leave at 150°C. If the average heat transfer coefficient is 150 W/m²K and the inner surface temperature of the tube is 110°C, determine (a) the tube length and (b) the rate of evaporation of water.arrow_forwardPlasma spraying is a process used to coat the surface of a material with a protective layer to prevent material degradation. In a plasma spray process, the protective coating in powder form is injected into a plasma jet. The powder is then heated until the droplets coalesce and are propelled over the surface of the material. Once deposited on the surface of the material, the molten droplets solidify and form a protective coating layer. Consider a plasma spray process using alumina (k = 30 W/m K, ρ = 3970 kg/m³ and cp = 800 J/kg K) powder that is injected into a plasma jet at T∞ = 15,000 ° C and h = 10,000 W/m²·K. Alumina powder is made up of spherical-shaped particles with a mean diameter of 60 μm and a melting point of 2300 °C.Solving, the amount of time it would take for the particles, with an initial temperature of 20 °C, to reach their melting point from the time they are injected into the plasma jet is 5,25x10 -4 s. Explain how the heat flow behaves in the system, using the…arrow_forward
- Plasma spraying is a process used to coat the surface of a material with a protective layer to prevent material degradation. In a plasma spray process, the protective coating in powder form is injected into a plasma jet. The powder is then heated until the droplets coalesce and are propelled over the surface of the material. Once deposited on the surface of the material, the molten droplets solidify and form a protective coating layer. Consider a plasma spray process using alumina (k = 30 W/m K, ρ = 3970 kg/m³ and cp = 800 J/kg K) powder that is injected into a plasma jet at T∞ = 15,000 ° C and h = 10,000 W/m²·K. Alumina powder is made up of spherically shaped particles with a mean diameter of 60 μm and a melting point of 2300 °C. Determine the amount of time it would take for the particles, with an initial temperature of 20 °C, to reach their melting point from the time they are injected into the plasma jet. Note: Give the solution from fundamental concepts of how the heat flow…arrow_forwardPlasma spraying is a process used to coat the surface of a material with a protective layer to prevent material degradation. In a plasma spray process, the protective coating in powder form is injected into a plasma jet. The powder is then heated until the droplets coalesce and are propelled over the surface of the material. Once deposited on the surface of the material, the molten droplets solidify and form a protective coating layer. Consider a plasma spray process using alumina (k = 30 W/m K, ρ = 3970 kg/m³ and cp = 800 J/kg K) powder that is injected into a plasma jet at T∞ = 15,000 ° C and h = 10,000 W/m²·K. Alumina powder is made up of spherical-shaped particles with a mean diameter of 60 μm and a melting point of 2300 °C.Solving, the amount of time it would take for the particles, with an initial temperature of 20 °C, to reach their melting point from the time they are injected into the plasma jet is 5,25x10 -4 s. Give a solution from fundamental concepts of how the heat flow…arrow_forwardA hot liquid (cp = 1000 J/kg∙K) flows at a flow rate of 0.05 kg/s inside a copper pipe with an inner diameter of 45 mm and a wall thickness of 5 mm. At the pipe exit, the liquid temperature decreases by 10°C from its temperature at the inlet. The outer surface of the 5-m-long copper pipe is black oxidized, which subjects the outer surface to radiation heat transfer. The air temperature surrounding the pipe is 10°C. Assuming that the properties of air can be evaluated at 35°C and 1 atm pressure, determine the outer surface temperature of the pipe. Is 35°C an appropriate film temperature for evaluation of the air properties?arrow_forward
- A 15-ft long strip of sheet metal is being transported on a conveyor at a velocity of 16 ft/s. To cure the coating on the upper surface of the sheet metal, infrared lamps providing a constant radiant flux of 1500 Btu/h?ft2 are used. The coating on the upper surface of the metal strip has an absorptivity of 0.6 and an emissivity of 0.7, while the surrounding ambient air temperature is 77°F. Radiation heat transfer occurs only on the upper surface, while convection heat transfer occurs on both upper and lower surfaces of the sheet metal. Determine the surface temperature of the sheet metal. Evaluate the properties of air at 180°F.arrow_forwardCooling water available at 10°C is used to condense steam at 30°C in the condenser of a power plant at a rate of 0.15 kg/s by circulating the cooling water through a bank of 5-m-long 1.2-cm-internal-diameter thin copper tubes. Water enters the tubes at a mean velocity of 4 m/s and leaves at a temperature of 24°C. The tubes are nearly isothermal at 30°C. Determine the average heat transfer coefficient between the water, the tubes, and the number of tubes needed to achieve the indicated heat transfer rate in the condenser.arrow_forwardLiquid water flows in a circular tube at a mass flow rate of 0.006 kg/s. The water enters the tube at 5°C, and the average convection heat transfer coefficient for the internal flow is 20 W/ m2⋅K. The tube is 3 m long and has an inner diameter of 25 mm. The tube surface is maintained at a constant temperature. The inner surface of the tube is lined with polyvinylidene chloride (PVDC) lining. According to the ASME Code for Process Piping, the recommended maximum temperature for PVDC lining is 79°C. If the water exits the tube at 15°C, determine the heat rate transferred to the water. Would the inner surface temperature of the tube exceed the recommended maximum temperature for PVDC lining? The specific heat of water at the bulk mean temperature of Tb = (Ti + Te)/2 = (5 + 15)°C/2 = 10°C is cp = 4194 J/kg·K. The heat transfer rate to the water is ______ W. The inner surface temperature of the tube is _____ (above/below) the maximum temperature for PVDC lining.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license