Heat and Mass Transfer: Fundamentals and Applications
5th Edition
ISBN: 9780073398181
Author: Yunus A. Cengel Dr., Afshin J. Ghajar
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Question
Chapter 4, Problem 125CP
To determine
The given proposal to reduce the time.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is the cooling duty to freeze water from 50°C to ice at 0°C, at the rate of 10 t/day?
Problem #2:
A mass of ice at -4°C is needed to cool 115 kg of vegetables in a bunker for 24
hours. The initial temperature of the vegetables is assumed to be 29°C. It is also
assumed that, within the 24-hr period, the average temperature inside the
bunker is 7°C. If the heat gained per hour in the bunker is 30% of the heat
removed to cool the vegetables from 29°C to 7°C, what would be the required
mass of ice in kg?
Use:
Specific heat of water 4.2292 kJ/kg-°C
• Specific heat of ice 1.9387 kJ/kg-°C
Specific heat of vegetables 3.35 kJ/kg-°C
Calculate the amount of heat required (in kJ) to raise the temperature of 23.4 g of ice at -11°C to steam at 135°C.
ΔHvap = 40.67 kJ/mol, ΔHfus = 6.008 kJ/mol, Cice = 2.092 J/g°C, Cwater = 4.184 J/g°C, Csteam = 1.841 J/g°C, Melting point = 0.00°C, Boiling Point = 100.0°C
Chapter 4 Solutions
Heat and Mass Transfer: Fundamentals and Applications
Ch. 4 - What is the physical significance of the Biot...Ch. 4 - What is lumped system analysis? When is it...Ch. 4 - In what medium is the lumped system analysis more...Ch. 4 - For which solid is the lumped system analysis more...Ch. 4 - For which kinds of bodies made of the same...Ch. 4 - Consider heat transfer between two identical hot...Ch. 4 - Consider heat transfer between two identical hot...Ch. 4 - Consider a hot baked potato on a plate. The...Ch. 4 - Consider a potato being baked in an oven that is...Ch. 4 - Consider two identical 4-kg pieces of roast beef....
Ch. 4 - Consider a sphere and a cylinder of equal volume...Ch. 4 - Obtain relations for the characteristic lengths of...Ch. 4 - Obtain a relation for the time required for a...Ch. 4 - A brick of 20310257mm in dimension is being burned...Ch. 4 - Prob. 15PCh. 4 - Prob. 16PCh. 4 - Metal plates...Ch. 4 - Prob. 18PCh. 4 - Prob. 19PCh. 4 - A 6-mm-thick stainless steel strip...Ch. 4 - After heat treatment, the 2-cm-thick metal plates...Ch. 4 - A long copper rod of diameter 2.0 cm is initially...Ch. 4 - Prob. 23PCh. 4 - Steel rods...Ch. 4 - To warm up some milk for a baby, a mother pours...Ch. 4 - A person is found dead at 5 p.m. in a room whose...Ch. 4 - Prob. 27PCh. 4 - In an experiment, the temperature of a hot gas...Ch. 4 - Prob. 29PCh. 4 - Pulverized coal particles are used in oxy-fuel...Ch. 4 - Oxy-fuel combustion power plants use pulverized...Ch. 4 - Plasma spraying is a process used for coating a...Ch. 4 - Consider a spherical shell satellite with outer...Ch. 4 - Prob. 34PCh. 4 - Prob. 35PCh. 4 - Prob. 36EPCh. 4 - Consider a sphere of diameter 5 cm, a cube of side...Ch. 4 - Prob. 38PCh. 4 - An egg is to be cooked to a certain level of...Ch. 4 - What is an infinitely long cylinder? When is it...Ch. 4 - What is the physical significance of the Fourier...Ch. 4 - Prob. 42CPCh. 4 - Prob. 43CPCh. 4 - Prob. 44CPCh. 4 - The Biot number during a heat transfer process...Ch. 4 - A body at an initial temperature of Ti, is brought...Ch. 4 - Prob. 47PCh. 4 - In a meat processing plant, 2-cm-thick steaks...Ch. 4 - Prob. 49PCh. 4 - Prob. 50PCh. 4 - Prob. 51PCh. 4 - Layers of 23-cm-thick meat slabs...Ch. 4 - Prob. 53PCh. 4 - Prob. 54PCh. 4 - Prob. 55EPCh. 4 - Prob. 56PCh. 4 - Prob. 57EPCh. 4 - Prob. 58PCh. 4 - A 30-cm-diameter, 4-m-high cylindrical column of a...Ch. 4 - Prob. 60PCh. 4 - Prob. 61PCh. 4 - Prob. 62PCh. 4 - Prob. 63PCh. 4 - Prob. 64PCh. 4 - Prob. 65PCh. 4 - Prob. 66PCh. 4 - Prob. 67PCh. 4 - Prob. 68PCh. 4 - Prob. 69PCh. 4 - For heat transfer purposes, an egg can be...Ch. 4 - Citrus fruits are very susceptible to cold...Ch. 4 - Prob. 72PCh. 4 - Prob. 73PCh. 4 - A 9-cm-diameter potato...Ch. 4 - Chickens with an average mass of 1.7 kg...Ch. 4 - Prob. 76PCh. 4 - In Betty Crocker s Cookbook, it is stated that it...Ch. 4 - Prob. 78PCh. 4 - Prob. 79PCh. 4 - Oranges of 2.5-in-diameter...Ch. 4 - Prob. 81EPCh. 4 - Under what conditions can a plane wall be treated...Ch. 4 - What is a semi-infinite medium? Give examples of...Ch. 4 - Consider a hot semi-infinite solid at an initial...Ch. 4 - Prob. 85EPCh. 4 - Prob. 86PCh. 4 - In areas where the air temperature remains below...Ch. 4 - Prob. 88PCh. 4 - A highway made of asphalt is initially at a...Ch. 4 - A thick aluminum block initially at 20C is...Ch. 4 - Prob. 91PCh. 4 - A thick wall made of refractory bricks...Ch. 4 - Prob. 93PCh. 4 - Prob. 94PCh. 4 - A thick wood slab (k=0.17W/m.K,=1.2810-7m2/s) and...Ch. 4 - Prob. 96PCh. 4 - Prob. 97PCh. 4 - Prob. 98PCh. 4 - Prob. 99PCh. 4 - Prob. 100PCh. 4 - Prob. 101PCh. 4 - A barefooted person whose feet are at 32C steps on...Ch. 4 - What is the product solution method? How is it...Ch. 4 - How is the product solution used to determine the...Ch. 4 - Prob. 105CPCh. 4 - Consider a short cylinder whose top and bottom...Ch. 4 - Prob. 107PCh. 4 - Prob. 108PCh. 4 - A hot dog can be considered to be a cylinder 5 in...Ch. 4 - Prob. 110PCh. 4 - Prob. 111PCh. 4 - A 2-cm-high cylindrical ice block...Ch. 4 - Prob. 113PCh. 4 - Prob. 114PCh. 4 - Prob. 115PCh. 4 - Prob. 116PCh. 4 - Prob. 117PCh. 4 - Prob. 118PCh. 4 - Prob. 119CPCh. 4 - How does refrigeration prevent or delay the...Ch. 4 - What are the environmental factors that affect the...Ch. 4 - What is the effect of cooking on the...Ch. 4 - Prob. 123CPCh. 4 - Prob. 124CPCh. 4 - Prob. 125CPCh. 4 - Prob. 126CPCh. 4 - How does the rate of freezing affect the...Ch. 4 - Prob. 128CPCh. 4 - Prob. 129CPCh. 4 - Prob. 130CPCh. 4 - Prob. 131CPCh. 4 - Prob. 132CPCh. 4 - Prob. 133PCh. 4 - Prob. 134PCh. 4 - Chickens with an average mass of 2.2 kg and...Ch. 4 - Prob. 136EPCh. 4 - Prob. 137PCh. 4 - Prob. 138PCh. 4 - A long roll of 2-m-wide and 0.5-cm-thick 1-Mn...Ch. 4 - Prob. 140PCh. 4 - Prob. 141PCh. 4 - Prob. 142PCh. 4 - During a picnic on a hot summer day, the only...Ch. 4 - Two metal rods are being heated in an oven with...Ch. 4 - Stainless steel ball bearings...Ch. 4 - Prob. 146PCh. 4 - Prob. 147PCh. 4 - In Betty crockers Cookbook, it is stated that it...Ch. 4 - A watermelon initially at 35C is to be cooled by...Ch. 4 - Prob. 150PCh. 4 - Prob. 151PCh. 4 - Prob. 152PCh. 4 - Prob. 153PCh. 4 - Prob. 154PCh. 4 - Prob. 155PCh. 4 - Prob. 156PCh. 4 - Prob. 157PCh. 4 - Prob. 158PCh. 4 - Prob. 159PCh. 4 - Lumped system analysis of transient heat...Ch. 4 - Prob. 161PCh. 4 - Prob. 162PCh. 4 - An 18-cm-long, 16-cm-wide, and 12-cm-high hot iron...Ch. 4 - Prob. 164PCh. 4 - Prob. 165PCh. 4 - Prob. 166PCh. 4 - Prob. 167PCh. 4 - Prob. 168PCh. 4 - A long 18-cm-diameter bar made of hardwood...Ch. 4 - Consider a 7.6-cm-long and 3-cm-diameter...Ch. 4 - Consider a 7.6-cm-diameter cylindrical lamb meat...Ch. 4 - Prob. 172PCh. 4 - A small chicken (k=0.45W/m.K,=0.1510-6m2/s) and...Ch. 4 - A potato may be approximated as a 5.7-cm-diameter...Ch. 4 - When water, as in a pond or lake, is heated by...Ch. 4 - A large chunk of tissue at 35C with a thermal...Ch. 4 - Prob. 177PCh. 4 - Citrus trees are very susceptible to cold weather,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 10 kg of frozen chicken at an initial temperature of -20°C is to be thawed and raised to a temperature of 10°C before cooking. The freezing point of the meat is -1.7°C and the specific heats above and below the freezing point are 3.1 kJ/kg-K and 1.6 kJ/kg-K, respectively. The heat of fusion (the amount of heat needed per unit mass to thaw chicken at the freezing point) is 233 kJ/kg. Find the total amount of heat that must be transferred to complete this the process.arrow_forwardLayers of 6-in-thick meat slabs (k = 0.26 Btu/h·ft·°F and a = 1.4 * 1026 ft2/s) initially at a uniform temperature of 50°F are cooled by refrigerated air at 23°F to a temperature of 36°F at their center in 12 h. Estimate the average heat transfer coefficient during this cooling process. Solve this problem using the Heisler charts.arrow_forwardIn determining the average rate of heating of a tank of 20% sugar syrup, thetemperature at the beginning was 20°C and it took 30 min to heat to 80°C. Thevolume of the sugar syrup was 50 ft3 and its density 66.9 lb/ft3. The specific heat ofthe sugar syrup is 0.9 Btu lb-1°F-1.(a) Convert the specific heat to kJ kg-1°C-1.(b) Determine the rate of heating, that is the heat energy transferred in unit time, in SI units (kJ s-1)arrow_forward
- Most automobiles have a coolant reservoir to catch radiator fluid that may overflow when the engine is hot. Such a radiator, made of copper, is filled to its 12-L capacity when at 10.0°C. -What volume of radiator fluid, in liters, will overflow when the radiator and fluid reach their 99.5°C operating temperature, given that the fluid’s thermal coefficient of volume expansion is 400.0 × 10-6 / °C? The coefficient of volume expansion for copper is 5.1 × 10-5 /°C.arrow_forwardSample Problem • Four metric tons of pork are to be stored at a temperature of -12°C in 8 hours. The product enters the chiller at a temperature of 21°C and the specific heats above and below freezing are 0.86 kCal/kg-°C and 0.51 kcal/kg-°C, respectively, and its latent heat of fusion is 48 kCal/kg. If the freezing temperature of the product is -5°C, determine the product load in kCal/hr. TCLarrow_forwardHumans are able to control their rates of heat production and heat loss to maintain a nearly constant core temperature of Tc = 37°C under a wide range of environmental conditions. This process is called thermoregulation. From the perspective of calculating heat transfer between a human body and its surroundings, we focus on a layer of skin and fat, with its outer surface exposed to the environment and its inner surface at a temperature slightly less than the core temperature, Ti = 35°C = 308 K. Consider a person with a skin/fat layer of thickness L = 2 mm and effective thermal conductivity k = 0.3 Wm ⋅ K. The person has a surface area A = 1.8 m2 and is dressed in a bathing suit. The emissivity of the skin is ε = 0.95.a). When the person is in still air at T∞ = 308 K, what is the skin surface temperature and rate of heat loss to the environment? Convection heat transfer to the air is characterized by a free convection coefficient of h = 2 W?2 ⋅ Kb). When the person is in water at T∞ =…arrow_forward
- If heated at the same rate and in the same manner, which would have a more even heat distribution during heating, a copper pan or a cast iron one? Why?arrow_forwardA jacketted-agitated vessel, fitted with a turbine agitator, is used for heating a water stream from 10°C to 54°C. The average heat transfer coefficient for water at the vessel’s inner-wall can be estimated from Nu = 0.76Re2/3Pr1/3. Saturated steam at 100°C condenses in the jacket, for which the average heat transfer coefficient in kW/m2·K is ho=5 13.1(Tg - Tw)20.25. The vessel dimensions are Dt = 0.6 m, H = 0.6 m and Da = 0.2 m. The agitator speed is 60 rpm. Calculate the mass rate of water that can be heated in this agitated vessel steadily.arrow_forwardA cylindrical can of pea puree has a diameter of 68.1 mm and a height of 101.6 mm. The can is initially at 29.4°C. 68.1 mm 101.6 mm The cans are vertically stacked in a retort, and steam at 115.6°C is admitted. The heat capacity of the metal wall of the can will be neglected. The properties of pea puree and steam are provided in the following Table: PHYSICAL PROPERTIES OF PEA PUREE STEAM PROPERTIES Thermal Conductivity = k=0.830 W/m- K Temperature = 115.6°C Thermal Diffusivity =a=2.007x107 m/s Heat-transfer coefficient of steam = h, = 4540 W/mKarrow_forward
- A fabricated food, in the form of small spherical pellets, is to be frozen in an air-blast freezer. The air-blast freezer is operating with air at -30°C. The initial product temperature is 25°C. The pellets have a diameter of 1.2 cm, and the density of the product is 980 kg/m³ . The initial freezing temperature is -2.5°C. The latent heat of fusion for this product is 280 kJ/kg. The thermal conductivity of the frozen product is 1.9 W/(m°C). The convective heat transfer coefficient is 50 W/(m² °C). Calculate the freezing time (h)arrow_forwardA fabricated food, in the form of small spherical pellets, is to be frozen in an air-blast freezer. The air-blast freezer is operating with air at -30°C. The initial product temperature is 25°C. The pellets have a diameter of 1.2 cm, and the density of the product is 980 kg/m3 . The initial freezing temperature is -2.5°C. The latent heat of fusion for this product is 280 kJ/kg. The thermal conductivity of the frozen product is 1.9 W/(m°C). The convective heat transfer coefficient is 50 W/(m2°C). Calculate the freezing time.arrow_forwardSteel balls (diameter = 21 mm, p = 7833 kg/m , k = 54 W/m•°C, Cp = 0.465 kJ/kg.°C, and a = 1.474x10 m /s) are annealed by heating them first to 870°C in a furnace and then allowing them to cool slowly to 85°C in ambient air at 27°C. What is the total rate of heat %3D transfer from the balls to the ambient air, when 2367 balls are to be annealed per hour (kW)? Select one: A. 11.15 B. 9.12 C. 9.85 D. 8.38 E. 10.50arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license