AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
7th Edition
ISBN: 9780357096789
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 39, Problem 4ASRQ
A car jumps out of gear into neutral, particularly when decelerating or going down hills: Technician A checks the shift lever and external gearshift linkage first. Technician B says that the clutch pilot bearing could be the problem. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
When discussing the possible causes for a shudder during acceleration,
Technician A says that a worn inner CV joint could be the cause.
Technician B says that insufficient differential gear backlash could be the cause of the problem.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
While discussing the possible causes for damage to the surface of a pressure plate.Technician A says a worn clutch disc can score the surface. Technician B saysinsufficient pedal free travel can cause it to overheat. Who is correct?a. Technician Ac. Both A and Bb. Technician Bd. Neither A nor B
When discussing shift problems,
Technician A says that worn or broken engine and
transaxle mounts can cause a transaxle to have
shifting problems.
Technician B that poor shift boot alignment
can cause a transaxle to jump out of gear.
says
Who is correct?
A. A only
C. Both A and B
B. B only
D. Neither A nor B
Chapter 39 Solutions
AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is too muchclearance, there will be a high pitch while the enginecranks. Technician B says that if there is too littleclearance, there will be a high pitch noise after theengine is started. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forwardTechnician A says a sticking inboard joint can cause the car to shimmy during acceleration. Technician B says a worn inboard joint can cause a clunking during acceleration and deceleration. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardThe clutch friction disc always rotates with thearrow_forward
- What can too much clutch pedal free play cause? a.hard gear shifting b.fast release bearing wear c.release fork wear d.clutch slippingarrow_forwardTechnician A says that if the shift for all forward gears is delayed, a slipping forward clutch is normally indicated. Technician B says that a bad forward clutch is indicated when there is a slip when the transmission shifts into any forward gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following components is replaced as an assembly?a. The transfer caseb. the viscous clutchc. The interaxle differentiald. all wheel drive transaxlesarrow_forward
- Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?arrow_forwardA vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced. Technician A says that the left inner CV joint may be the source of the noise. Technician B says that the left outer CV joint may be causing the noise. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forwardA discussion concerning CV joint testing is being held. Technician A says that a recommended method to check CV joints is to raise the vehícle so that the lower control arms are hanging freely; at this point the engine can be accelerated while noise checks can be performed. Technician B says that the vehicle should be road tested so that the CV joints can be checked under load. Who is correct? O a. A only O b. B only c. Both A and B d. Neither A nor Barrow_forward
- What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to improve mobility when driving conditions become difficultc. to drive both rear driving wheels when vehicle is stuck.d. to drive the rear axle assemblyarrow_forwardA hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this condition will cause the engine to stall as soon as you put the transmission into gear. Technician B says that this condition will cause the transmission to shift late. Who is correct?arrow_forwardList three possible causes of a noisy bearing during clutch operation.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License