A hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this condition will cause the engine to stall as soon as you put the transmission into gear. Technician B says that this condition will cause the transmission to shift late. Who is correct?

A hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this condition will cause the engine to stall as soon as you put the transmission into gear. Technician B says that this condition will cause the transmission to shift late. Who is correct?

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter39: Manual Transmission/transaxle Service

Section: Chapter Questions

Problem 8ASRQ: During a test drive, a noise that appears to be transmission related disappears when the driver...

See similar textbooks

Related questions

Q: when adjusting a heavy-duty pull type manual adjusting clutch what is used to compensate for normal…

A: There are two types of clutch adjustment mechanisms: 1) Manually adjusted clutch 2) Self-adjusting…

Q: Describe the purpose of a viscous clutch.

A: Viscous clutch The clutch is part of the machine that is used to operate for the transmission's…

Q: The component used to ensure that the mainshaft (output shaft) and main (speed) gear locked to it…

A: The component used to ensure that the mainshaft (output shaft) and main (speed) gear locked to it…

Q: Explain the benefits of dynamic testing of automatic transmission fluid

A: Automatic transmission fluid: It is a type of fluid which is used in vehicle for self-shifting and…

Q: Technician A says when removing a transmission, the rear of the engine will usually need to be…

A: Answer

Q: Name the three drive configurations that a greatset can transfer torque.

A: Given data : Drive configurations

Q: Among the following, which drive transmits exact velocity ratio during power transmission. Gear…

A: Gear drive

Q: Technician A says that some systems use a special modulated shift control solenoid. Technician B…

A: In automobile the transmission system uses shift control solenoid which shift the gear…

Q: Explain the difference between rotary and vortex fluid flow in a torque converter.

A: Inside the torque converter, there are two types of fluid flow. The vortex flow is the first, and…

Q: Technician A says that the proper fluid level for a manual transmission is normally to the bottom of…

A: Solution:

Q: crankshaft

A: Statement is true

Q: When discussing the various gear positions of a transfer case, Technician A says that when the…

A: Transfer case is used to switch from two wheel drive to four wheel drive and vice versa. It also…

Q: in an automatic transmission or transaxle, the torque converter is used to

A: The Torque Converter A torque converter is a device that is used to transmit the rotating power of…

Q: While discussing the various types of transmissions found on today’s vehicles: Technician A says…

A: Sliding collar transmission-In sliding collar transmission we must move a fork which engage or…

Q: Technician A says that double-cone synchronizers have friction material on both sides of the…

A: Technician A says that double-cone synchronizers have friction material on both sides of the…

Q: What is power transmission?

A: Anwser :- Power Transmission :- In mechanical terms, to transmit the kinetic power from one rotating…

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: Technician A says hydraulic pressure affects transmission shift points. Technician B says hydraulic…

A: Affects of hydraulic Pressure : When hydraulic fluid enters into the bore of the cylinder it forces…

Q: Technician A says that throttle position is an important input in most electronic shift control…

A: In electronically controlled automatic transmission, the most appropriate gear ratio for the power…

Q: Among the following, which drive is least reliable in power transmission. O Gear drive O Rope drive

A: The transfer of energy from its place of generation to a place where it is used to do useful work is…

Q: airborne transmission 2. common vehicle transmission

Q: Technician A says the torque converter uses engine oil to provide a fluid link between engine and…

A: Given data, Torque converter and its main work and use.

Q: the number one cause of clutch disc failure

A: Clutch :- The function of a clutch is to transmit the power from rotating shaft or motor or engine…

Q: Make a Drive Shaft in SINUMERIK (ste

A: A drive shaft is a vehicle shaft that transmits power from the transmission to the wheels. The…

Q: Shift linkage enclosed within the transmission or transaxle case is called as 1) external linkage 2)…

A: Column Shift: In a column shift there is a rod which connects the handle with the lever attached at…

Q: when discussing shift problems, technician A says that worn or broken engine and transaxle mounts…

A: The explanation of technician A is correct because the shifting problems may cause due to worn or…

Q: Which of the following is NOT true about the initial tension in a flat belt drive? OA. It should be…

A: A spherical joint is also known as ball and socket joint, allows three relatives rotation between…

Q: While discussing transmission adaptive learning: Technician A says that the transmission learns to…

A: Transmission Adaptive learning:-The automatic transmission is designed in such a way that it has a…

Q: (B) Choose the correct answer for the following statements:- 1- For a faster response time, a spool…

A: Given question: For a faster response time, a spool type of directional control valve use a-…

Q: In a V-belt drive, which of the following is true about the groove angles of the sheaves, given the…

A: We can answer first question since the exact one is not specified. Please resubmit the question by…

Q: The four common configurations used as the finaldrives on FWD vehicles are the __ gear, __ gear,__…

A: The four often utilized final drive designs for FWD cars are chain drive, hypoid gear, planetary…

Q: While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts…

A: Technician A is right as blackened pinion is a sign of overloading and are used as indicators of…

Q: Question 1: (answer must be handwritten) What is special about timing belts compared to classic flat…

Q: On an electronically controlled transmission list 5 things that could cause incorrect shift times…

A: In and electronically transmission system is the best transmission system as it gives proper engine…

Q: Tech A says that the weight of the flywheel smoothes out the engine’s power pulses. Tech B says that…

A: Flywheel: A flywheel is a mechanical device having higher value of moment of inertia. This high…

Q: Is minor pulsation a normal condition in typical clutch operation?

A: When the clutch pedal is disengaged ,the movement felt on clutch is known as clutch pulsation.theses…

Q: If an actuator fails to move, name five possible causes.f an actuator has slow or erratic motion,…

A: Actuator is a component of a machine which capable in moving in a controlled mechanism.It consist of…

Q: Design some devices that replaces the clutch in semi or fully automatic systems and transmits engine…

A: The purpose of a clutch in an automobile is to transmit power from the engine to the transmission.…

Q: - Name the parts of the engine lubrication system shown in the figure below:

A: we are required to name the different parts of lub. system

Q: True or False? In most transmissions and transaxles,there is one synchronizer assembly for each…

A: Given Synchronizer for gear speed To find Verify the statement

Q: Which of the following is not a base Sl unit?

A: Explanation 27 As we know that there are only seven fundamental unit which can we written as 1.…

Q: List five things that could cause incorrect shift times and poor shifting quality

Q: What is the importance of studying how to perform assemble/disassemble manual transmission?

A: Manual transmission is also known as multi-speed transmission which involves in gear change in the…

Q: frequency of the system.

A: GIVEN; Mass of two identical springs is; m=12 kgEach of stiffness,k=50 kN/m=50×103 N/mIt is under…

Q: Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the…

A: The basic function of shift solenoids is to control the pressures within fluid system and they don’t…

Q: List at least three causes of noise that are not transmission related but may appear to be

A: In the transmission systems, noise is one of the biggest concern. Noise is used to identify the…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

When discussing the possible causes for a shudder during acceleration, Technician A says that a worn inner CV joint could be the cause. Technician B says that insufficient differential gear backlash could be the cause of the problem. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor B
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
Technician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?
Technician A says that some manual transmissions use 85/90 weight gear oil or synchromesh transmission fluid.Technician B says that some manual transmissions use automatic transmission fluid.Who is correct?
Technician A says that limited- slip differential clutch packs are designed to slip when the vehicle turns a corner. Technician B says that a special additive is placed in the hypoid gear lubricant to promote clutch pack slippage on corners. Who is correct?
Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?
When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?
While diagnosing the cause of TCC shudder: Technician A checks the fluid pressure sent to the clutch. Technician B says that because the shudder occurs only after the clutch is engaged, the problem is the engine, transmission, or another component of the driveline. Who is correct?
Technician A says that some systems use a special modulated shift control solenoid. Technician B says that some systems use a special modulated converter clutch control solenoid. Who is correct? Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct? Technician A says that throttle position is an important input in most electronic shift control systems. Technician B says that vehicle speed is an important input for most electronic shift control systems. Who is correct? Technician A says that a faulty TP sensor can cause delayed shifts. Technician B says that delayed shifts can be caused by an open shift solenoid. Who is correct? Technician A says that some shift solenoids can be activated by providing a ground for the solenoid. Technician B says that some shift solenoids can be activated by…
Three factors to consider before deciding to apply a transmission of gear drives
A car jumps out of gear into neutral, particularly when decelerating or going down hills: Technician A checks the shift lever and external gearshift linkage first. Technician B says that the clutch pilot bearing could be the problem. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
While discussing a pressure test: Technician A says that this test is the most valuable diagnostic check for slippage when a gear is engaged. Technician B says that the test can identify the cause of late or harsh shifting. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B