Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 35, Problem 29QLP
Describe the characteristics of electronic gages.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
I want to solve the required squares and their units of measurement in regularity, please
2. Form tolerances are independent of all other
Features
O Size Limits
Datums
O Tolerances
?
Which is a more precise (or exact) measuring tool, the top-loading balance or the graduated cylinder?
Chapter 35 Solutions
Manufacturing Engineering & Technology
Ch. 35 - What is metrology?Ch. 35 - Explain how a meter is defined and measured.Ch. 35 - Explain what is meant by standards for...Ch. 35 - What is the basic difference between...Ch. 35 - What is meant by comparative length measurement?Ch. 35 - Explain how flatness is measured. What is an...Ch. 35 - Describe the principle of an optical comparator.Ch. 35 - Why have coordinate measuring machines...Ch. 35 - What is the difference between a plug gage and...Ch. 35 - What are dimensional tolerances? Why is their...
Ch. 35 - Prob. 11RQCh. 35 - Explain the difference between tolerance and...Ch. 35 - What is the difference between bilateral and...Ch. 35 - How is straightness measured?Ch. 35 - When is a clearance fit desirable? An interference...Ch. 35 - What factors contribute to deviations in the...Ch. 35 - Why are the words accuracy and precision...Ch. 35 - Prob. 18QLPCh. 35 - Prob. 19QLPCh. 35 - Prob. 20QLPCh. 35 - Dimensional tolerances for nonmetallic parts...Ch. 35 - Prob. 22QLPCh. 35 - Review Fig. 35.20, and comment on the range...Ch. 35 - In the game of darts, is it better to be accurate...Ch. 35 - What are the advantages and limitations of GO...Ch. 35 - Comment on your observations regarding Fig. 35.19.Ch. 35 - What are gage blocks? Explain three methods...Ch. 35 - Why is it important to control temperature during...Ch. 35 - Describe the characteristics of electronic gages.Ch. 35 - What method would you use to measure the...Ch. 35 - Prob. 31QLPCh. 35 - Review Fig. 35.21 and give reasons that there is a...Ch. 35 - Assume that a steel rule expands by 0.07% due to...Ch. 35 - If the same steel rule as in Problem 35.33 is used...Ch. 35 - A shaft must meet a design requirement of being at...Ch. 35 - Describe your thoughts on the merits and...Ch. 35 - Take an ordinary vernier micrometer (see Fig....Ch. 35 - Obtain a digital micrometer and a steel ball of,...Ch. 35 - Prob. 41SDPCh. 35 - Prob. 42SDPCh. 35 - Inspect various parts and components in...Ch. 35 - Prob. 45SDPCh. 35 - Prob. 46SDPCh. 35 - Prob. 47SDPCh. 35 - Conduct an Internet search, and make a list of...Ch. 35 - Prob. 49SDP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is a dimensioning tolerance?arrow_forwardTooling Design ☐ Device need to be placed by Pick and place with accuracy of +/- 50um into nest. • Device size = 1.0 xo.8xo.6mm (Tolerance = +/-0.05mm all sides) 0.8 mm Y mm Z mm Y= Z= _mm, Explain mm, Explainarrow_forwardWhat is calibration and why is it important?arrow_forward
- Explain Precision & Accuracy with the help of industrial applications.arrow_forwardCan someone explain how to read a mm drum dial micrometer and check my work please?arrow_forwardWhy might a 50 division vernier caliper not be more advantageous, in terms of measurement accuracy, than a 10 division vernier caliper?arrow_forward
- 2There are two different indicated drawings in Fig.1. (1) Judge the tolerance principle they used respectively; (2) Calculate their allowed perpendicularity tolerance in MMS respectively; (3) Calculate their allowed perpendicularity tolerance in LMS respectively (4) If the actual size is 17.9 mm, the actual perpendicularity error is 00.009mm, judge whether it is qualified according to Fig.1 (a) or Fig.1 (b) respectively. ( ¢18 8 00.01 (M) A 0.1 -0.1 I ø0.01 |4 (a) (b)arrow_forwardPlease provide complete solution with units of measurement.arrow_forwardDescribe a situation where you might use a Vernier caliper or micrometer. Explain why you would use this measurement tool in the situation you described.arrow_forward
- 7. What is a tolerance?arrow_forwardIndicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle cylinder is Odh7, use Envelope requirement; b) Cylindricity tolerance of d is 0.009mm, straightness of axis of od is $0.012mm; c) Total run-out tolerance of right end surfaces related to axis of Pd is 0.01 mm; d) The surface of od cylinder is obtained by the method of removing material, and the maximum allowable value of Rz is 0.4µm. All surfaces are obtained by the method of removing material, and all the roughness Ra allowable value is 6.4 pm.arrow_forwardRefer to the Ø.8740 ± .0005 dimension.A) Where is the tolerance specified ? ____________________________ B) Is its tolerance unilateral or bilaterial ? _________________________ C) What is its tolerance ? _____________________________________ D) What is the MMC, ? ________________________________ E) What is the LMC,? _________________________________arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY