Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 35, Problem 10RQ
What are dimensional tolerances? Why is their control important?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Research and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing.
Explain how this tolerance is defined
What is the tolerance zone (and Material Boundary) for a non-cylindrical feature such as a slot or groove?
What is notch sensitivity?
Chapter 35 Solutions
Manufacturing Engineering & Technology
Ch. 35 - What is metrology?Ch. 35 - Explain how a meter is defined and measured.Ch. 35 - Explain what is meant by standards for...Ch. 35 - What is the basic difference between...Ch. 35 - What is meant by comparative length measurement?Ch. 35 - Explain how flatness is measured. What is an...Ch. 35 - Describe the principle of an optical comparator.Ch. 35 - Why have coordinate measuring machines...Ch. 35 - What is the difference between a plug gage and...Ch. 35 - What are dimensional tolerances? Why is their...
Ch. 35 - Prob. 11RQCh. 35 - Explain the difference between tolerance and...Ch. 35 - What is the difference between bilateral and...Ch. 35 - How is straightness measured?Ch. 35 - When is a clearance fit desirable? An interference...Ch. 35 - What factors contribute to deviations in the...Ch. 35 - Why are the words accuracy and precision...Ch. 35 - Prob. 18QLPCh. 35 - Prob. 19QLPCh. 35 - Prob. 20QLPCh. 35 - Dimensional tolerances for nonmetallic parts...Ch. 35 - Prob. 22QLPCh. 35 - Review Fig. 35.20, and comment on the range...Ch. 35 - In the game of darts, is it better to be accurate...Ch. 35 - What are the advantages and limitations of GO...Ch. 35 - Comment on your observations regarding Fig. 35.19.Ch. 35 - What are gage blocks? Explain three methods...Ch. 35 - Why is it important to control temperature during...Ch. 35 - Describe the characteristics of electronic gages.Ch. 35 - What method would you use to measure the...Ch. 35 - Prob. 31QLPCh. 35 - Review Fig. 35.21 and give reasons that there is a...Ch. 35 - Assume that a steel rule expands by 0.07% due to...Ch. 35 - If the same steel rule as in Problem 35.33 is used...Ch. 35 - A shaft must meet a design requirement of being at...Ch. 35 - Describe your thoughts on the merits and...Ch. 35 - Take an ordinary vernier micrometer (see Fig....Ch. 35 - Obtain a digital micrometer and a steel ball of,...Ch. 35 - Prob. 41SDPCh. 35 - Prob. 42SDPCh. 35 - Inspect various parts and components in...Ch. 35 - Prob. 45SDPCh. 35 - Prob. 46SDPCh. 35 - Prob. 47SDPCh. 35 - Conduct an Internet search, and make a list of...Ch. 35 - Prob. 49SDP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What happens if you add a small imperfection to a system that has a saddle-node bifurcation?arrow_forwardWhat are the significance of tolerance and allowance in production process? Diagram?arrow_forwardResearch and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing. Discuss a specific feature in a specific product/design case where calling out this geometric tolerance would be relevant for performance, assembly, or general operation.arrow_forward
- What is the relation between product tolerance and product variation?arrow_forwardWhy it is necessary to perform calibration on a standard prior to performing a Nano indentation performance?arrow_forwardI need help with number 15. How much would the tolerance be? And where would the Level part go? I've attached the question and my sketch for reference.arrow_forward
- What is a coordinate measuring machine (CMM)? Explain the working with some applications.arrow_forwardIndicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle cylinder is Odh7, use Envelope requirement; b) Cylindricity tolerance of d is 0.009mm, straightness of axis of od is $0.012mm; c) Total run-out tolerance of right end surfaces related to axis of Pd is 0.01 mm; d) The surface of od cylinder is obtained by the method of removing material, and the maximum allowable value of Rz is 0.4µm. All surfaces are obtained by the method of removing material, and all the roughness Ra allowable value is 6.4 pm.arrow_forward(USCS units) A GO/NO-GO plug gage is needed to inspect a 1.000 ± 0.020 in diameter hole. A wear allowance is applied to the GO side of the gage. The allowance = 2% of the total tolerance band. Determine the nominal sizes of (a) the GO gage and (b) the NO-GO gage.arrow_forward
- The design specification on the part is that the diameter = 45.000 ± 0.150 mm. (a) What proportion of parts fall outside the tolerance limits? (b) If the process is adjusted so that its mean diameter = 45.000 mm and the standard deviation remains the same, what proportion of parts fall outside the tolerance limits?arrow_forwardWhat precisely do we mean when we say that the standards need to be wide and consistent when we talk about them?arrow_forwardIn the context of our teaching, which one of the below statements is mostly correct about in detailed design of a component? In the reporting, I do not need to include the reasoning for my design decision for a good quality report. I cannot use appendix, so I am struck with the word limit for reporting. For a good clarity, I should not explicitly report what are the key dimensions and their tolerances in the drawing and in the body of text. The word count limit for detailed design report is 160O.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
What is Metrology in Mechanical Engineering? | Terminologies & Measurement; Author: GaugeHow;https://www.youtube.com/watch?v=_KhMhFRehy8;License: Standard YouTube License, CC-BY