Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 32, Problem 6CQ
Hydraulic lifters or hydraulic lash adjusters (HLA) may not bleed down property and cause an engine to miss if ___________.
- a. the engine oil is one quart low
- b. the wrong API-rated engine oil is used
- c. the wrong SAE-rated engine oil is used
- d. both a and b
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that the engine oil drain
plug typically needs to be replaced with a
new one at each oil change. Technician B
says that engine oil drain plugs must be
tightened with a torque wrench when they
are installed. Who is correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
1.Name type of failures in engine blocks
Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?
Chapter 32 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 32 - How is the camshaft driven by the crankshaft?Ch. 32 - What drives the high-pressure fuel pump on a GDI...Ch. 32 - What is meant by an interference engine?Ch. 32 - How does variable valve timing help improve engine...Ch. 32 - The camshaft makes __________ for every revolution...Ch. 32 - A DOHC V-6 has how many camshafts? a. 4 b. 2 c. 3...Ch. 32 - Which timing chain type is also called a silent...Ch. 32 - Many technicians always use new pushrods because...Ch. 32 - Hydraulic valve lifters can make a ticking noise...Ch. 32 - Hydraulic lifters or hydraulic lash adjusters...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
CONCEPT QUESTIONS
15.CQ3 The ball rolls without slipping on the fixed surface as shown. What is the direction ...
Vector Mechanics for Engineers: Statics and Dynamics
Select a mechanical component from Part 3 of this book (roller bearings, springs, etc.), go to the Internet, an...
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
Locate the centroid of the area. Prob. 9-17
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
The spring of k and unstretched length 1.5R is attached to the disk at a radial distance of 0.75R from the cent...
Engineering Mechanics: Statics
23.23 A highly oxidized and uneven round bar is being turned on a lathe. Would you recommend a small or a large...
Manufacturing Engineering & Technology
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pumparrow_forwardIf the oil on the dipstick looks milky gray, it is possible that there is water (or coolant) being mixed into the oil. This could have been caused by any of the following EXCEPΤ: Select one: a. a bad head gasket. b. a cracked head. C. a leaky oil cooler. d. a leaky fuel injector.arrow_forwardExplain briefly 1. Valve lag 2. intake lagarrow_forward
- The misfiring exceeds ____________ to ____________ percent in a ____________ rpm period if Type B engine misfires are excessive.arrow_forwardA vehicle has had several radiator replacements, and each time there has been pinhole leaks in the aluminum. Technician A states that the engine coolant may need to be exchanged more often. Technician B states that the engine grounds should be inspected closely since this could be the cause. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardTechnician A says that when draining the engine oil, the engine should be fully cold for best results. Technician B says that the engine should be running when checking the engine oil level. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- what are the two tune up methods used for a variety of big bore cummins enginesarrow_forwardTrue or False? The camshaft is always locatedin the engine block.arrow_forwardThe gas/oil mixture used in a two stroke engine has been properly mixed. The carburetor high speed & cruise circuit is adjusted to lean. Tech a says that the lean adjustment may cause the engine to fail due to improper lubrication: tech b says that it may cause the engine to fail because of overheating. Who is correct?arrow_forward
- What provisions are usually included on tractor engines to aid in the correct timing of the camshaft?arrow_forward__________ pump is prepared for oil production and fuel transfer a. Vane b. Screw c. Lobe d. Geararrow_forwardWhich of the following statements about EVAP systems is not true? a. If the system is purging vapors from the charcoal canister when the engine is running at high speeds, rough engine operation will occur. b. Cracked hoses or a canister saturated with gasoline may allow gasoline vapors to escape to the atmosphere, resulting in gasoline odor in and around the vehicle. c. Rough idle, flooding, and other similar conditions can indicate a saturated canister. d. A vacuum leak in the system can cause starting and performance problems.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY