Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 31, Problem 8R
What is meant by regulator creep?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
How to answer Number 3 of the problem? Thank you
Why isnt the temprature used in this equation?
Give an example of the Resistance Factor?
Chapter 31 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 31 - What is the purpose of a pressure regulator?Ch. 31 - What may result if a pressure regulator is not...Ch. 31 - Describe how a single-stage regulator operates.Ch. 31 - Is the torch pressure always the same as the...Ch. 31 - Why does the high-pressure gauge on a regulator...Ch. 31 - How does the operation of a safety release valve...Ch. 31 - Describe the difference between an argon cylinder...Ch. 31 - What is meant by regulator creep?Ch. 31 - Who can repair regulators?Ch. 31 - Why must the pressure be released from a regulator...
Ch. 31 - Why are combination welding and cutting torches...Ch. 31 - What is the advantage of using an injector-type...Ch. 31 - What should be done to the valve packing if the...Ch. 31 - What may happen to a tip seat if it is incorrectly...Ch. 31 - What can happen to a tip if it is excessively...Ch. 31 - What is the difference between a reverse flow...Ch. 31 - What are Siamese hoses?Ch. 31 - Why must the pressure be bled off hoses when work...Ch. 31 - What is the difference between a backfire and a...Ch. 31 - Why is a neutral flame the most commonly used...Ch. 31 - What properties should a good leak-detecting...Ch. 31 - Why must the oxygen cylinder valve be opened all...Ch. 31 - How long should hoses be purged?Ch. 31 - What should be done with cylinders that have...Ch. 31 - How should the spark lighter be held to light a...Ch. 31 - Once the torch is lit, why must the acetylene flow...Ch. 31 - What type of piping can be used for a manifold...Ch. 31 - What elements make up all hydrocarbons?Ch. 31 - What are the separate parts that make up an...Ch. 31 - Use Table 31-3 to determine which fuel gas...Ch. 31 - Approximately how long would it take a 50/50...Ch. 31 - Use Table 31-4 to determine which fuel gas has the...Ch. 31 - How is acetylene produced?Ch. 31 - Why is it not safe to use acetylene above 15 psig...Ch. 31 - Use Table 31-5 to determine the largest tip...Ch. 31 - Where is the highest temperature and where is the...Ch. 31 - Use Table 31-6 to determine what would be the...Ch. 31 - What are methylacetylene-propadiene fuel gases...Ch. 31 - Use Table 31-7 to determine which oxygen fuel-gas...Ch. 31 - Which fuel gas has the strongest odor and is...Ch. 31 - What is the major advantage of using propane or...Ch. 31 - Use Table 31-8 to determine which fuel gas would...Ch. 31 - What two major safety problems does hydrogen...Ch. 31 - Why should coat hangers not be used as gas welding...Ch. 31 - Explain the significance of the AWS filler metal...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is a thermopile?arrow_forwardTHERMO-DYNAMIC PROBLEM,solve it correctlyarrow_forwardA compressor that has been in service for 20 years has finally broken down beyond repair, and now must be replaced. The old 180hp machine cost $1200 and its cost index at that time was 144.5. The new machine will be 400hp. How much will the new machine cost, given that today's compressor index is 252.4 and the power-sizing exponent for compressor sizing is 0.32? A: $929 B: $2706 C: $1434 D: $2096 E: $1549arrow_forward
- what is second law of thermo dynamic?arrow_forwardWhy are the young modulus not used?arrow_forwardI have three parts that need to be answered pertaining to the print provided below. What size paper was used for the original version of this print? (Multiple Choice)ABCD What is the total quantity of subassemblies required for this assembly? (Multiple Choice)A: twoB: threeC: fourD: five What term describes the relationship of the axis of the 1/2″ pipe plug with the main,longer axis of the bottom assembly? (Multiple Choice)A: PerpendicularB: ParallelC: VerticalD: X shapedarrow_forward
- A calliper brake is required for the front wheels of a van with a braking capacity of 900 Nm for each brake. Preliminary design estimates have set the brake geometry as ri=100 mm, To=160 mm and 0=45°. A pad with a coefficient of friction of 0,3 has been selected.arrow_forwardwhy does classical mechanisms failedarrow_forwardWhat is the final temperature of block M ?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Relationship Between Elastic Constants and Connecting Equations; Author: Engineers Academy;https://www.youtube.com/watch?v=whW5PnM7Pug;License: Standard Youtube License