Welding: Principles and Applications (MindTap Course List)
Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
bartleby

Videos

Textbook Question
Book Icon
Chapter 31, Problem 31R

Approximately how long would it take a 50/50 mixture of oxygen and acetylene to flash back through a 21-ft-(7.62-m) long hose?

Blurred answer
Students have asked these similar questions
5670 mm The apartment in the ground floor of three floors building in Fig. in Baghdad city. The details of walls, roof, windows and door are shown. The window is a double glazing and air space thickness is 1.3cm Poorly Fitted-with Storm Sash with wood strip and storm window of 0.6 cm glass thickness. The thickness of door is 2.5 cm. The door is Poor Installation. There are two peoples in each room. The height of room is 280 cm. assume the indoor design conditions are 25°C DBT and 50 RH, and moisture content of 8 gw/kga. The moisture content of outdoor is 10.5 gw/kga. Calculate heat gain for living room : الشقة في الطابق الأرضي من مبنى ثلاثة طوابق في مدينة بغداد يظهر في مخطط الشقة تفاصيل الجدران والسقف والنوافذ والباب. النافذة عبارة عن زجاج مزدوج وسمك الفراغ الهوائي 1.3 سم ضعيف الاحكام مع ساتر حماية مع إطار خشبي والنافذة بسماكة زجاج 0.6 سم سماكة الباب 2.5 سم. الباب هو تركيب ضعيف هناك شخصان في كل غرفة. ارتفاع الغرفة 280 سم. افترض أن ظروف التصميم الداخلي هي DBT25 و R50 ، ومحتوى الرطوبة 8…
How do i solve this problem?
Q4/ A compressor is driven motor by mean of a flat belt of thickness 10 mm and a width of 250 mm. The motor pulley is 300 mm diameter and run at 900 rpm and the compressor pulley is 1500 mm diameter. The shaft center distance is 1.5 m. The angle of contact of the smaller pulley is 220° and on the larger pulley is 270°. The coefficient of friction between the belt and the small pulley is 0.3, and between the belt and the large pulley is 0.25. The maximum allowable belt stress is 2 MPa and the belt density is 970 kg/m³. (a) What is the power capacity of the drive and (b) If the small pulley replaced by V-grooved pulley of diameter 300 mm, grooved angle of 34° and the coefficient of friction between belt and grooved pulley is 0.35. What will be the power capacity in this case, assuming that the diameter of the large pulley remain the same of 1500 mm.

Chapter 31 Solutions

Welding: Principles and Applications (MindTap Course List)

Ch. 31 - Why are combination welding and cutting torches...Ch. 31 - What is the advantage of using an injector-type...Ch. 31 - What should be done to the valve packing if the...Ch. 31 - What may happen to a tip seat if it is incorrectly...Ch. 31 - What can happen to a tip if it is excessively...Ch. 31 - What is the difference between a reverse flow...Ch. 31 - What are Siamese hoses?Ch. 31 - Why must the pressure be bled off hoses when work...Ch. 31 - What is the difference between a backfire and a...Ch. 31 - Why is a neutral flame the most commonly used...Ch. 31 - What properties should a good leak-detecting...Ch. 31 - Why must the oxygen cylinder valve be opened all...Ch. 31 - How long should hoses be purged?Ch. 31 - What should be done with cylinders that have...Ch. 31 - How should the spark lighter be held to light a...Ch. 31 - Once the torch is lit, why must the acetylene flow...Ch. 31 - What type of piping can be used for a manifold...Ch. 31 - What elements make up all hydrocarbons?Ch. 31 - What are the separate parts that make up an...Ch. 31 - Use Table 31-3 to determine which fuel gas...Ch. 31 - Approximately how long would it take a 50/50...Ch. 31 - Use Table 31-4 to determine which fuel gas has the...Ch. 31 - How is acetylene produced?Ch. 31 - Why is it not safe to use acetylene above 15 psig...Ch. 31 - Use Table 31-5 to determine the largest tip...Ch. 31 - Where is the highest temperature and where is the...Ch. 31 - Use Table 31-6 to determine what would be the...Ch. 31 - What are methylacetylene-propadiene fuel gases...Ch. 31 - Use Table 31-7 to determine which oxygen fuel-gas...Ch. 31 - Which fuel gas has the strongest odor and is...Ch. 31 - What is the major advantage of using propane or...Ch. 31 - Use Table 31-8 to determine which fuel gas would...Ch. 31 - What two major safety problems does hydrogen...Ch. 31 - Why should coat hangers not be used as gas welding...Ch. 31 - Explain the significance of the AWS filler metal...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Text book image
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Extent of Reaction; Author: LearnChemE;https://www.youtube.com/watch?v=__stMf3OLP4;License: Standard Youtube License