Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 31, Problem 4SA
What is the difference between the pulse width and the duty cycle of an injector?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
List five advantages the use of piezoelectric injectorshas over solenoid-based injectors.
How does a servo valve work?
Name the parts of a fuel injector.
Chapter 31 Solutions
Automotive Technology
Ch. 31 - List four service precautions for working on the...Ch. 31 - What is indicated by a LTFT reading of 24 percent?Ch. 31 - Describe how testing GDI fuel systems differs from...Ch. 31 - What is the difference between the pulse width and...Ch. 31 - How can you use a dual trace scope to make sure...Ch. 31 - What are three possible problems that can allow...Ch. 31 - What is the purpose of having two accelerator...Ch. 31 - What is indicated by a negative LTFT value?Ch. 31 - What problem may result from dirt buildup on an...Ch. 31 - What is the difference between STFT and LTFT?
Ch. 31 - True or False? The signals from an air-fuel ratio...Ch. 31 - Prob. 2TFCh. 31 - Which of the following is the most likely cause of...Ch. 31 - The PCM checks for a closed throttle plate each...Ch. 31 - Which of the following would not cause a...Ch. 31 - While discussing the causes of...Ch. 31 - While discussing IAC valve diagnosis: Technician A...Ch. 31 - While discussing IAC motor removal, service, and...Ch. 31 - While discussing injector testing: Technician A...Ch. 31 - While discussing airflow sensors: Technician A...Ch. 31 - While discussing scan tool diagnosis of fuel...Ch. 31 - While discussing a high idle speed problem:...Ch. 31 - While discussing the causes of a rich air-fuel...Ch. 31 - While diagnosing an idle speed problem: Technician...Ch. 31 - While looking at fuel trim values: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is meant by sequential firing of fuel injectors?arrow_forward1: List the safety mechanisms that contrast medium injection devices are equipped with. 2: What are the five factor that affect injector flow rate?arrow_forwardWhile discussing central port injection systems: Technician A says that CPI systems use one injector and several injector nozzles. Technician B says that CPI systems open each injector sequentially. Who is correct? A.Technician A B.Technician B C.Both A and B D.Neither A nor Barrow_forward
- The injector pulse width is the __________ ___ ________ the injector opens and sprays fuel.arrow_forward1. The purpose of running this injector balance test is to determine which injector is restricted, inoperative, or delivering fuel differently than the other injectors. Replacing a complete set of injectors can be expensive. a. Describe the step involve in conducting injector balance test. b. Based on the recorded data on the power balance test in Table 1. Explain the condition on each injector. Table 1 Data collected from power balance test. Injector 1 2 3 Initial pressure (psi) 45 45 45 Second pressure 32 36 25 (psi)arrow_forwardTechnician A says that air-fuel ratios can be regulated by controlling the “on time” of the injectors. Technician B says that the air-fuel ratio can be regulated by controlling the pressure applied to the individual injectors. Who is correct?arrow_forward
- What is the advantage of using an injector-type mixing chamber?arrow_forwardAn engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole, but it doesn't not start when fuel is added to the carburetor throat. Tech a says that the problem may be that the exhaust valve is not closing completely due to carbon buildup. Tech b says it may be due to a defective carburetor mounting gasket. Who is correct?arrow_forwardHow can you use a dual trace scope to make sure that the injectors are firing at the correct time?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY