DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 31, Problem 3P
A gear-broaching machine can complete the gear in 15 s (about 240 part/hr). How many additional gears per year are needed to cover the broaching tooling cost if each broach on the machine cost $250? Do you think the broach tool life is sufficient to handle that number of parts? What about TiN coating the broaches (cost $10.00/broach)?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
wing
(3) You are to produce a machine part (a shaft) with different diameters
S0mm.35mm and 30mm with thread and keyway at
the end of the shaft
(a) How many machines and cutting tools will you use to produce
this part
1
The end of a large tubular workpart is to be faced on a NC vertical boring mill.
The part has an outside diameter of 38.0 in and an inside diameter of 24.0
in. If the facing operation is performed at a rotational speed of 40.0 rev/min,
feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting
time to complete the facing operation and the cutting speeds and metal
removal rates at the beginning and end of the cut.
A cylindrical mild steel work piece of Ø55 X 200mm undergoes a turning operation on a lathe machine to
reduce the diameter to Ø 45mm. The cutting parameters are 23 m/minute, 0.3 mm/ revolution and 0.5
mm are cutting speed, feed and depth of cut respectively.
Determine the following.
i) Time for single pass (minutes).
ii) Find number of passes required to reduce the diameter from Ø55 to Ø45mm.
iii) Total time required to complete the turning operation in minutes (Tfinal).
Chapter 31 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 31 - How does the pitch diameter differ from the major...Ch. 31 - Prob. 2RQCh. 31 - Prob. 3RQCh. 31 - Prob. 4RQCh. 31 - Prob. 5RQCh. 31 - Explain the meaning of 14 -20 UNC-3A.Ch. 31 - Prob. 7RQCh. 31 - Prob. 8RQCh. 31 - Prob. 9RQCh. 31 - Prob. 10RQ
Ch. 31 - Prob. 11RQCh. 31 - Prob. 12RQCh. 31 - Prob. 13RQCh. 31 - What is the reason for using a taper tap before a...Ch. 31 - Prob. 15RQCh. 31 - Can a fluteless tap be used for threading a hole...Ch. 31 - What provisions should a designer make so that a...Ch. 31 - What is the major advantage of a spiral-point tap?Ch. 31 - Prob. 19RQCh. 31 - Is it desirable for a tapping fluid to have...Ch. 31 - How does thread milling differ from thread...Ch. 31 - What are the advantages of making threads by...Ch. 31 - Prob. 23RQCh. 31 - Prob. 24RQCh. 31 - What is a fluteless tap?Ch. 31 - Why is the involute form used for gear teeth?Ch. 31 - What is the diametral pitch of a gear?Ch. 31 - What is the relationship between the diametral...Ch. 31 - On a sketch of a gear, indicate the pitch circle,...Ch. 31 - What five requirements must be met for gears to...Ch. 31 - What are the advantages of helical gears compared...Ch. 31 - Prob. 32RQCh. 31 - What difficulty would be encountered in bobbing a...Ch. 31 - What is the only type of machine on which...Ch. 31 - Prob. 35RQCh. 31 - Why arent more gears made by broaching?Ch. 31 - What is the most important property of a crown...Ch. 31 - What are three basic processes for machining...Ch. 31 - Which basic gear-machining process is utilized in...Ch. 31 - When a helical gear is machined on a milling...Ch. 31 - Why is a gear-hobbing machine much more productive...Ch. 31 - Prob. 42RQCh. 31 - What are the advantages of cold-roll forming for...Ch. 31 - Prob. 44RQCh. 31 - Under what conditions should shaving not be used...Ch. 31 - Prob. 46RQCh. 31 - Can lapping be used to finish cast iron gears?Ch. 31 - What factors are usually checked in inspecting...Ch. 31 - What are the basic methods for gear finishing?Ch. 31 - A hob that has a pitch diameter of 76.2 mm is used...Ch. 31 - In Figure 31.17, a form-milling operation and...Ch. 31 - A gear-broaching machine can complete the gear in...Ch. 31 - Prob. 4PCh. 31 - If only three gears described in Problem 4 were to...Ch. 31 - Based on the size and shape of the product,...Ch. 31 - What type of engineering materials might be able...Ch. 31 - Prob. 3CS
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Determine the tension developed in each cable for equilibrium of the 300-lb crate.
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
If they are at the positions shown when t = 0, determine the time when the cars are side by side, and the time ...
Engineering Mechanics: Dynamics (14th Edition)
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
The special-purpose milling cutter is subjected to the force of 1200 N and a couple of 240Nm as shown. Determin...
Engineering Mechanics: Statics
the internal loading at point B.
Engineering Mechanics: Statics & Dynamics (14th Edition)
For the manometer shown in Fig. 3.30, calculate (pA - Pb) Figure 3.30
Applied Fluid Mechanics (7th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q24. For the below figure please write its part program. The depth of the cut is 0.25 inches (Finishing operation), while the tool's diameter is 0.5 inches. Consider the speed and feed. -0.75- - - 1.0 60⁰ RO.25 (0, 0) 0.75-arrow_forwardExercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a multi-tool centre lathe having eight tools in operation. The feed is 0-3 mm/rev, the specific cutting pressure/tool is 2 000N/mm and the total power consumed for the operation is 14 kW. If the depth of cut is to be kept the same for each tool, calculate the depth of cut/tool in mm.arrow_forwardThe workpiece of size 50 mm x 90 mm length is to be reduced to 0 42 mm x 85 mm. If the depth of cut is 0.5 mm, feed is 0.25 mm/rev and cutting speed is 45 m/min find the time taken to complete one job and production rate at the end of 8 hr shift.arrow_forward
- Exercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a multi-tool centre lathe having eight tools in operation. The feed is 0-3 mm/rev, the specific cutting pressure/tool is 2 000N/mm2 and the total power consumed for the operation is 14 kW. If the depth of cut is to be kept the same for each tool, calculate the depth of cut/tool in mm. (Ans. 3-8 mm)arrow_forwardQuestion 3. A cemented carbide tool is used to turn a part with length = 18.0 in and diameter = 3.0 in. The parameters in the Taylor equation are: n= 0.27 and C = 1200. The rate for the operator and machine tool = $33.00/hr, and the tooling cost per cutting edge = $2.00. It takes 3.0 min to load and unload the workpart and 1.50 min to change tools. The feed = 0.013 in/rev. Determine: a) Cutting speed for maximum production rate, b) Tool life in min of cutting, and c) Cycle time and cost per unit of product.arrow_forwardA Ø1.0” piece of titanium needs to be turned on a lathe using a carbide cutting tool. The surface speed is 170 ft/min and the chip load is .015 in/rev. What is the recommended feed for the turning operation above?arrow_forward
- Q1\ a) The operation of drilling is to be done with a 25.4 mm ( diameter) twist drill in a brass workpiece. The hole is a blind-hole with the point angle = 118°, and a depth of 50 mm . The speed of 25 m/min, feed of 0.25 mm/rev. Calculate: (1) the time of cutting to complete the drilling operation, and (2) metal removal rate during the operation.arrow_forwardA mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 48 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.1 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 48.8 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm ( (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpmarrow_forwardA number of through holes with 10-mm-diameter have been drilled through 30-mm thick cast iron plate. At a cutting speed of 25 m/min, the high-speed steel drill tool lasted for 44 holes. But, when the cutting speed increased to 35 m/min, the drill tool lasted for only five holes. The feed used in the both cases is 0.08 mm/rev. Determine the values of n and Cin the Taylor tool life equation for the data, where cutting speed v is expressed in m/min, and tool life T is expressed in min.arrow_forward
- A cylindrical rod is machined using turning processes. It is given that the cutting speed is 120min ¹, and feed per tooth is 0.0025 m/min. The outer diameter is 35mm, the length of the rod is 130m and the inner diameter is 22mm. The number of teeth is 6. Find Rotational speed, Feed rate, Machining time, and Depth of cut.arrow_forwardA mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutesarrow_forwardA mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License