Principles of Instrumental Analysis
7th Edition
ISBN: 9781305577213
Author: Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 31, Problem 31.7QAP
Interpretation Introduction
Interpretation:
The physical changes associated with endothermic or exothermic peaks in differential scanning calorimetry and differential thermal analysis are to be listed.
Concept introduction:
Determination properties of materials are done on the basis of change of temperature and it is known as thermal analysis. Many methods are there as example DSC or DTA etc.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
What structural features of Hydroxypropyl Acrylate (HPA) allow it to be detected by HPLC?
Quantitative Analysis by External Standard Method
Calcium in a juice sample is determined by atomic absorption spectrophotometry.
A stock solution of calcium is prepared by dissolving 1.834 g of CaCl, 2H20 in water and diluting to 1000.0 mL.
A substock calcium solution was prepared by transferring 10.00 mL of the stock to a 100.00 mL volumetric
flask and diluting to the mark. Three standard solutions of calcium were prepared by transferring 2.500 mL.
5.00 mL and 10.00 mL of substock to 50.00 mL volumetric flasks and diluting to the mark.
The sample is prepared by transferring 1.000 mL of fruit juice from the original bottle to a 25.00 mL flask and
diluting to the mark.
Strontium chloride is added to all solutions before dilution to avoid phosphate interference. Instrumental
response of the standards is measured against the blank, and the following readings are recorded: 9.10, 18.6
and 37.0. The sampie reading is 28.1.
Using the multipoint method, find the concentration of calcium in…
What is the significance of the max of a
spectrum?
What are the other uses of the
spectrophotometer?
Chapter 31 Solutions
Principles of Instrumental Analysis
Knowledge Booster
Similar questions
- What does a refractometer reading of 2 mean when distilling ethanol?arrow_forwardWhy chromatography is an important tool for analysis of organic compounds?arrow_forward5. Draw and label a box diagram for a double-beam spectrophotometer. What advantages does a double beam spectrophotometer have over a single beam spectrophotometer?arrow_forward
- After creating her standard curve for absorption versus the concentration (M) of FD&C Red 40, a student found that her best fit linear line for FD&C Red 40 was y = 2,681x + -0.002. Her Kool-Aid sample had an absorbance of 0.337. If 0.55 grams of Kool-Aid powder was used to prepare an 8-fl oz cup of her assigned flavor, what is the percent by mass of FD&C Red 40 in her 8-fl oz cup?arrow_forwardA student performs this and records the following data from the complted chromatogram. the solvent has moved 7.30 cm Component A produces a blue spot that has moved 5.80 cm. Component B produces a pink spot that has moved 2.45 cm. Component C produces a tan spot that has moved 4.10cm. Calculate the Rf values for component.arrow_forwardIf all of the SCN-was not converted completely to FeNCS^2+ when the calibration curve was prepared, would this raise or lower the value of Keq? Explain.arrow_forward
- Gas Chromatography (GC) is one of the useful techniques in analytical chemistry. Give two important components in GC.arrow_forwardOne method for quantitative determination of the concentration of constituents in a sample analyzed by gas chromatography is the area normalization method. In this method, complete elution of all of the sample constituents is necessary. The area of each peak is then measured and corrected for differences in detector response to the different eluates. This correction is accomplished by dividing the area by an empirically determined correction factor. The concentration of the analyte is found from the ratio of its corrected area to the total corrected area of all peaks. For a chromatogram containing three peaks, the relative areas were found to be 16.4, 45.2, and 30.2 in the order of increasing retention time. Calculate the percentage of each compound if the relative detector responses were 0.60, 0.78, and 0.88, respectivelyarrow_forwardWhat types of samples can be analyzed by IR?How are substances that are opaque (nottransparent) handled using this technique?arrow_forward
- What is the importance of the following analytical methods in chemical analysis? i. UV-vis spectrophotometry ii. HPLC iii. GCarrow_forwardIn a TLC experiment, how do you identify the components of an unknown mixture? Select one: Combine the mixture with multiple known compounds and look for the largest spots. Compare the color of the mixture spots to the colors of pure known compounds. Combine the mixture with a series of known compounds and observe the color of the dots. O Compare the Rf values of the mixture components to the Rf values of pure known compounds.arrow_forwardA 5.3 × 10-2 M solution is to be used to prepare a series of five 100 mL solutions of varying concentration for use in creating a calibration curve for a spectrophotometric experiment. Determine the concentrations of each of the five dilutions if 10 mL aliquots of the current solution is used for V1.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning