Mathematics For Machine Technology
8th Edition
ISBN: 9781337798310
Author: Peterson, John.
Publisher: Cengage Learning,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 31, Problem 17A
In Exercises 17 and 18, refer to the following sentence and to the following given vernier caliper settings to find values A, B, and C. "The zero vernier scale graduation lies between A and B on the main scale, and the vernier graduation Ccoincides with the main scale graduation." The answer to the first part of Exercise 17 is given.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Chapter 31 Solutions
Mathematics For Machine Technology
Ch. 31 - Measure this line segment to the nearest 164.Ch. 31 - A hole has a diameter of 13.741 mm 0.002mm+0.005mm...Ch. 31 - For the measurement 74.38 mm, find (a) the degree...Ch. 31 - Express 87.6 inches as feet.Ch. 31 - If 1450 parts can be produced in 15.35 hours, how...Ch. 31 - Prob. 6ACh. 31 - Read the decimal-inch vernier caliper measurements...Ch. 31 - Read the decimal-inch vernier caliper measurements...Ch. 31 - Read the decimal-inch vernier caliper measurements...Ch. 31 - Read the decimal-inch vernier caliper measurements...
Ch. 31 - Read the decimal-inch vernier caliper measurements...Ch. 31 - Prob. 12ACh. 31 - Read the decimal-inch vernier caliper measurements...Ch. 31 - Read the decimal-inch vernier caliper measurements...Ch. 31 - Prob. 15ACh. 31 - The tables for Exercises 15 and 16 give the...Ch. 31 - In Exercises 17 and 18, refer to the following...Ch. 31 - In Exercises 17 and 18, refer to the following...Ch. 31 - The distance between the centers of two holes can...Ch. 31 - The distance between the centers of two holes can...Ch. 31 - Prob. 21ACh. 31 - Prob. 22ACh. 31 - The distance between the centers of two holes can...Ch. 31 - Read height gage measurement settings in Exercises...Ch. 31 - Read height gage measurement settings in Exercises...Ch. 31 - The hole locations of the block in Figure 31-11...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, advanced-math and related others by exploring similar questions and additional content below.Similar questions
- Note: For Exercises 13 through 62 that follow, round the answers to 3 decimal places wherever necessary. In Exercises 13 through 16, add the following signed numbers as indicated. 14. a. +12 + (-5) b. +18 + (—26) c. -20 + (+ 19) d. -23 + 17 e. -25+3arrow_forwardThe distance between the centers of two holes can be checked with a vernier caliper. The position of the caliper in measuring the inside distance between two holes is shown in Figure 29-10. To determine the setting on the caliper, subtract the radius of each hole (one-half the diameter) from the center distance. In Exercises 19 through 23, give the hole diameters and the distances between centers. For each, determine (1) the main scale setting and (2) the vernier scale setting. All dimensions are in inches.arrow_forwardThe distance between the centers of two holes can be checked with a vernier caliper. The position of the caliper in measuring the inside distance between two holes is shown in Figure 29-10. To determine the setting on the caliper, subtract the radius of each hole (one-half the diameter) from the center distance. In Exercises 19 through 23, give the hole diameters and the distances between centers. For each, determine (1) the main scale setting and (2) the vernier scale setting. All dimensions are in inches 23. Note: Hole tolerances and center distance tolerances are shown. Maximum and minimum vernier scale settings are required.arrow_forward
- In Exercises 41 and 42, round to two decimal places. A goat is tethered to a barn by a 12-ft chain. If the chain is connected to the barn at a point 6 ft from one end of the barn, what is the area of the pasture that the goat is able to graze?arrow_forwardConsidering that the consecutive dials on the natural gas meter rotate in opposite directions, what is the current reading in cubic feet of usage? The initial direction is clockwise.arrow_forwardThe hole locations of the block in Figure 31-11 are checked by placing the block on a surface plate and indicating the bottom of each hole using a height gage with an indicator attachment. Determine the height gage settings from the bottom of the part to the bottom of the holes. Assume that the actual hole diameters and locations are the same as the given dimensions. The setting for Hole Number 1 is given.arrow_forward
- The length, L, of the point on any standard 118° included angle drill, as shown in Figure 12-5, can be calculated using the formula L=0.3 O where represents the diameter of the drill. Determine the lengths of the following drill points with the given diameters. Round to 3 decimal places for inches and 1 decimal place for millimeters. a. 12 b. 14 c. 38 d. 10 mm e. 25 mm f. 45 mmarrow_forwardThe following problem is based on the Parallelogram Law. In the scaled drawing, each unit corresponds to 50 mph. A small airplane travels due east at 250 mph. The wind is blowing at 50 mph in the direction due north. Using the indicated diagonal and use it to determine the speed of the airplane in miles per hour.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Mathematics For Machine TechnologyAdvanced MathISBN:9781337798310Author:Peterson, John.Publisher:Cengage Learning,
Elementary Geometry For College Students, 7eGeometryISBN:9781337614085Author:Alexander, Daniel C.; Koeberlein, Geralyn M.Publisher:Cengage,
Elementary Geometry for College StudentsGeometryISBN:9781285195698Author:Daniel C. Alexander, Geralyn M. KoeberleinPublisher:Cengage Learning 
Trigonometry (MindTap Course List)TrigonometryISBN:9781305652224Author:Charles P. McKeague, Mark D. TurnerPublisher:Cengage Learning
Functions and Change: A Modeling Approach to Coll...AlgebraISBN:9781337111348Author:Bruce Crauder, Benny Evans, Alan NoellPublisher:Cengage Learning
Algebra: Structure And Method, Book 1AlgebraISBN:9780395977224Author:Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. ColePublisher:McDougal Littell
Mathematics For Machine Technology
Advanced Math
ISBN:9781337798310
Author:Peterson, John.
Publisher:Cengage Learning,
Elementary Geometry For College Students, 7e
Geometry
ISBN:9781337614085
Author:Alexander, Daniel C.; Koeberlein, Geralyn M.
Publisher:Cengage,
Elementary Geometry for College Students
Geometry
ISBN:9781285195698
Author:Daniel C. Alexander, Geralyn M. Koeberlein
Publisher:Cengage Learning
Trigonometry (MindTap Course List)
Trigonometry
ISBN:9781305652224
Author:Charles P. McKeague, Mark D. Turner
Publisher:Cengage Learning
Functions and Change: A Modeling Approach to Coll...
Algebra
ISBN:9781337111348
Author:Bruce Crauder, Benny Evans, Alan Noell
Publisher:Cengage Learning
Algebra: Structure And Method, Book 1
Algebra
ISBN:9780395977224
Author:Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole
Publisher:McDougal Littell
Propositional Logic, Propositional Variables & Compound Propositions; Author: Neso Academy;https://www.youtube.com/watch?v=Ib5njCwNMdk;License: Standard YouTube License, CC-BY
Propositional Logic - Discrete math; Author: Charles Edeki - Math Computer Science Programming;https://www.youtube.com/watch?v=rL_8y2v1Guw;License: Standard YouTube License, CC-BY
DM-12-Propositional Logic-Basics; Author: GATEBOOK VIDEO LECTURES;https://www.youtube.com/watch?v=pzUBrJLIESU;License: Standard Youtube License
Lecture 1 - Propositional Logic; Author: nptelhrd;https://www.youtube.com/watch?v=xlUFkMKSB3Y;License: Standard YouTube License, CC-BY
MFCS unit-1 || Part:1 || JNTU || Well formed formula || propositional calculus || truth tables; Author: Learn with Smily;https://www.youtube.com/watch?v=XV15Q4mCcHc;License: Standard YouTube License, CC-BY