A helium balloon is to lift a payload to an altitude of 40 km, where the atmospheric pressure and temperature are 3.0 mbar and − 25°C, respectively. The balloon skin is polyester with specific gravity of 1.28 and thickness of 0.015 mm. To maintain a spherical shape, the balloon is pressurized to a gage pressure of 0.45 mbar. Determine the maximum balloon diameter if the allowable tensile stress in the skin is limited to 62 MN/m2. What payload can be carried?
Want to see the full answer?
Check out a sample textbook solutionChapter 3 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Additional Engineering Textbook Solutions
Engineering Mechanics: Statics & Dynamics (14th Edition)
Introduction To Finite Element Analysis And Design
Applied Statics and Strength of Materials (6th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Manufacturing Engineering & Technology
- An unbendingly held tie bar in a warming chamber has a width of 60 mm and is tensioned to a heap of 150 kN at a temperature of 15°C. What is the underlying pressure in the bar and what will be the resultant pressure when the temperature in the chamber has ascended to 50°C?arrow_forwardThe cabin pressure in a spacecraft is maintained at 14.3 psia. What will be the force in N on a window 2.9ft wide and 1.7ft high when the craft is in outer space?arrow_forwardThe manhole cover of an ammonia storage tank is to be held by 25 stud bolts. If the pressure inside the storage tank will remain constant at 12.5 kg/cm2 and the manhole diameter is 508 mm, what should be the stress area of the carbon steel bolts?arrow_forward
- What is the altitude an airplane is flying if the measured air pressure is 640.12471304150 psf? Assume standard condition.arrow_forwardLiquid manometers measure differential pressure by balancing the weight of a liquid between two pressures. Light liquids such as water can measure small pressure differences; mercury or other heavy liquids are used for large pressure differences. A 15° inclined manometer containing mercury is connected to two taps A an B containing water. Tap B is 5 ft vertically higher than Tap A. When the pressure in Tap B is 5 psi, the manometer reads 4 inches along the inclined tube. Calculate the new manometer reading (in inches) if the pressure in Tap A is increased by 3 psi.arrow_forwardA spherical research balloon is filled with 420 m3 of atmospheric air at a temperature of 10°C. If the air inside the balloon is heated to 80°C according to PVn =C, where n = 0. What will be the final diameter of the balloon? show cancellation of units and formula usedarrow_forward
- 4. A structure is attached to the ocean floor as shown in the figure below. A 2-m-diameter hatch is located in an inclined wall and hinged on one edge. Determine the minimum air pressure, pı, within the container that will open the hatch. Neglect the weight of the hatch and friction in the hinge. Take y = 10. 1x10³ N/m³. Free surface Seawater 10 m 30 Hatch - Hinge Air pressure, P1arrow_forwardAtmospheric pressure is used to lift a part with a surface area of 0.008m^2. The piece is placed in a chamber from which the air has been extracted. Atmospheric pressure is given by 100kPa. For this configuration answer the following: a) If it is desired that the piece rise only h = 2m in the cylinder, determine what its weight would have to be (kN). b) If the cylinder opens to the atmosphere above the piece, determine the force necessary to achieve the 2m rise with the piece. Patm TESE harrow_forwardA cylindrical water tank is 8m in diameter and 12m high. If the tank is to be completely filled, determine the minimum thickness of the tank plating if the stress is limited to 40 MPa. Hint: The water pressure at a certain level is a product of its weight and depth. (p=yH) 13.18 mm O 5.89 mm 10.25 mm O 12.6 mm 11.77 mm 14.13 mm O 21 mm 26 mm 28.25 mm O 24.5 mmarrow_forward
- What is the pressure in an altitude where the density is 1.011626576 kg/m? Assume standard condition.arrow_forwardA vertical, cylindrical tank, 6 ft in diameter and 12 ft high, is held together by means of two steel hoops, one at the top and one at the bottom. Molasses (SGmalasses = 1.50) stands to a depth of 9 ft in the tank. The cross-sectional area of each hoop is 0.5 in?. The tank is open at the top. Let T1 and T2 be the tensile forces in the top and bottom hoops, respectively, and oi and o2, the stresses in the top and bottom hoops, respectively. Determine the following: Parameter Unit (a) FTOTAL (b) T1 Ib Ib (c) T2 Ib (d) 01 psi (e) 02 psiarrow_forwardThe pressure inside a competion grade tennis ball is 1.6 times higher than the atmospheric pressure. The diameter and wall thicknwess of the tennis is 66 mm and 2.8 mm, respectively. Considering the atmospheric pressure as 100,000 Pa, determine the stress in the tennis ball at rest. Express the result in MPa with 2 decimal points.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY