Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 29, Problem 9CQ
Technician A says that engine parts should be cleaned before a thorough test can be done to detect cracks. Technician B says that pressure testing can be used to find cracks in blocks or cylinder heads. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A vehicle has had several radiator
replacements, and each time there has been
pinhole leaks in the aluminum. Technician A
states that the engine coolant may need to be
exchanged more often. Technician B states
that the engine grounds should be inspected
closely since this could be the cause. Who is
correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Technician A says that if the oil pressure
shows low on the vehicle's gauge, engine
oil pressure should be verified using a
manual test gauge. Technician B says that
if a vehicle's oil pressure gauge reads too
high, engine oil pressure should be
verified using a manual test gauge. Who is
correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
1.Name type of failures in engine blocks
Chapter 29 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 29 - What are the five methods that could be used to...Ch. 29 - Explain magnetic crack inspection, dye-penetrant...Ch. 29 - How can engine block and cylinder heads be...Ch. 29 - What precautions need to be followed when cleaning...Ch. 29 - What is the purpose of stop drilling?Ch. 29 - Abrasive pads or discs should be used __________....Ch. 29 - What actually does the cleaning when using steam?...Ch. 29 - Aqueous-based cleaning means __________. a. water...Ch. 29 - A pyrolytic oven is used to clean parts; however,...Ch. 29 - Which media is best to use for cleaning parts, as...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Find the change in length of side AB.
Mechanics of Materials, 7th Edition
A nozzle at A discharges water with an initial velocity of 36 ft/s at an angle with the horizontal. Determine ...
Vector Mechanics for Engineers: Dynamics
Three rigid bodies, 2,3, and 4, are connected by four springs as shown in the figure. A horizontal force of 1,0...
Introduction To Finite Element Analysis And Design
For the beam loading of Figure P334, draw the complete shearing force and bending moment diagrams, and determin...
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
A 20-lb force is applied to the control rod AB as shown. Knowing that the length of the rod is 9 in. and that t...
Statics and Mechanics of Materials
Describe the structural changes that take place when a plain-carbon eutectoid steel is slowly cooled from the a...
Foundations of Materials Science and Engineering
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe the proper procedure to seal a puncture in a tire.arrow_forwardThe CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart. Technician A says that one or more of the engine/transaxle's mounts may be broken. Technician B says that one or more of the engine/transaxle's subframe mounts may be broken. Who is correct? O a. A only O b.B only C. Both A and B O d. Neither A nor Barrow_forwardWhich of the following statement is correct Select one: Friction causes objects to slip down Friction causes objects to slow down Friction causes objects to break down Friction causes objects to move at small forcearrow_forward
- Given two oil According to the standard by Society Automotive Engineers the oil , by comparing the 5W-30 with the 10W-30, a. The 5W-30 has lower viscosity than 10W-30 at low temperature. O b. The 5W-30 has higher viscosity at the high temperature. c. Both of the oils are suitable for cold weather O d. All of the above are true.arrow_forwardWhich of the following would NOT be cause for rejection when checking the tire condition? Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame. Any tire tread or recap is separated or any tire is flat. All of the statements shown are cause for rejection. Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.arrow_forwardTechnician A says that the engine oil drain plug typically needs to be replaced with a new one at each oil change. Technician B says that engine oil drain plugs must be tightened with a torque wrench when they are installed. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Which of the following is not a common way to identify the location of cracks in the engine block or cylinder head? Pressure checks Vacuum test Magnetic particle inspection Penetrativearrow_forwardTrue or False? An oil with the classification of 5W-30 has the viscosity of both a 5- and 30-weight oil. The 5W means the oil has a viscosity of 5 when warm and a 30 rating when it is cold.arrow_forwardWhile discussing the causes of extreme engine bearing damage Technician A says that contaminated and old engine oil could be the cause. Technician B says that a leaking radiator could be the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- FGI and FKJ correct but incorrect afterwards.arrow_forwardA technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling system pulled into a vacuum when cold. Technician A states that a leak in the surge tank could be the cause. Technician B states that the radiator cap is most likely defective. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardWhich of the following would NOT be cause for rejection when checking the windshield and other glass? Any window is broken or has sharp or jagged edges. Any window other than the windshield is cracked, starred, scratched, or discolored so as to obstruct the driver’s view. The vehicle is not equipped with approved safety glass or is not equipped with a windshield. The windshield has a 2 inch diameter“star”.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY